Walk-Through Metal Detector User Manual
Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/).
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Note Provides additional information to emphasize or supplement important points of the main text.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations ● Use of the product must be in strict compliance with the local electrical safety regulations. Transportation ● Keep the device in original or similar packaging while transporting it. ● Keep all wrappers after unpacking them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper.
Contents Chapter 1 Over View .................................................................................................................. 6 System Description................................................................................................................... 6 Functions .................................................................................................................................. 7 Key Features ..........................................................................
5.5.1 Set Motion Detection .................................................................................................... 32 5.5.2 Set Video Tampering Alarm........................................................................................... 33 5.5.3 Set Alarm Input ............................................................................................................. 34 5.5.4 Set Exception Alarm ..............................................................................................
5.11.9 Time and Date ............................................................................................................. 68 5.11.10 Set RS-232 ................................................................................................................. 69 5.11.11 Set RS-485 ................................................................................................................. 69 5.11.12 Set Same Unit ....................................................................................
Factory: anti-theft; · Hotels, restaurants, entertainment venues, dance halls: visitors check There is no health hazard will be caused to the pregnant woman, people wearing a pacemaker, or to any other person passing through the metal detector when the procedure is followed. Functions Non-contact temperature measurement: skin-surface temperature screening with accurately personnel matching. Temperature accuracy:±0.5 ℃ , detection distance: 0.5 to 1.5 m, target height: 1.45 m to 1.
Supports AGC4.0, DDE, and 3DNR Supports dual-light fusion image Supports visible light and thermal imaging frame over lay 15 pseudo colors: white, black, red, etc. Visible Light Functions 4 MP, 1/2.7 “ CMOS, Max.
Chapter 2 Installation Installation Environment In order to ensure the optimal operation of the detector and the maximum flow of people, the following important factors are taken into account to minimize the impacts made by different interference sources. Large fixed or immovable metal objects should be at least 10cm (4in) away from the detector (to detect large metal objects). This has less impact on the sensitivity, but may make the detector more susceptible to vibration.
The maximum distance between the electronic interference source and the receiving coil should be maximum. The recommended minimum distance is 0.5-4m (20-157in). However, the actual distance should vary according to the specific situation. The Interference may be caused by electronic control panel, radio equipment and computer, image display, high-power motor and transformer, AC wire, transistor control circuit, flash fluorescent lamp, ARC welding equipment, etc.
Note: Make the Receiving Coil (RX) away from the interference source. Make sure the interference level displayed on the environment inspection indicator is less than 2. Security Check Point Layout The performance of the check point may be impacted by the following causes: Arrange the line of the waiting people. Make sure there is only one person in the detector for every check. Make sure the metal detector not interfere the operation of the detector.
the two launch panels as long as possible) as close as possible. Install the launch panel close to the interference sources. Use the frequency combination of lowest interference level Installation and Wiring 1. Take out the device and accessories.
2. Install the door planks, beam, and main control panel. Tighten the screws to fix all the components. 3. Connect the detection cables. 4. 5. Take out the camera and mounting bracket. Rotate and remove the enclosure. 6. Route the cables through the cable hole, and fix the bracket on the camera with three screws.
7. 8. Rotate and install the enclosure. Hang the camera (with mounting bracket) onto the beam. 9. Secure the mounting bracket with four screws. 10. 11. Adjust the camera to make it forward the people flow direction. Upend the device.
Chapter 3 Calibration The purpose of the calibration is to enable the operational characteristics of the detector to meet the requirements of the security level. Calibration the detector before the security checkpoint starts work. Prior to calibration, probe requirements should be determined, for example, what is most dangerous goods likely to be detected. The detector should be calibrated with a reference representing the danger level. Principle 1.
Sensitivity settings will also affect the anti-interference of the detector. It is not recommended to use a sensitivity that is too high for the operation place. In order to adjust the detection sensitivity, the test object should be placed in different positions on the body in different ways and carried through the detector. Steps: 1. Define the overall sensitivity, which can be adjusted manually(except for ankle height). 2. Define ankle height sensitivity (zone sensitivity).
III. Test Daily inspection: - Calibration with test objects calibration - Detective door mechanical fixation Chapter 4 Metal Detector Local Configuration Before use, the frequency of the detection gate (50/60hz) should be set according to the power frequency of different countries. The frequency setting will affect the performance of the detection gate detector.
1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Home: standby interface/alarm interface/working environment monitoring Security level: with 1 0 0 levels can be adjusted, the higher the level, the higher the sensitivity/mode selection. Zone sensitivity: the highest sensitivity is 255, and the lowest is 0. There are two kinds of sensitivity Settings: automatic and manual.
Chapter 5 Thermal Camera Configuration Description of Thermal Camera Thermal & Optical Bi-spectrum network camera equipped with built-in GPU which supports intelligent behavior analysis algorithm, can realize high-precision VCA detection and real-time alarm. It is applied to perimeter defense and fire-prevention purposes in critical infrastructures such as community, villa, construction site, factory, 4S stores, and so on.
Device Activation and Accessing To protect the security and privacy of the user account and data, you should set a login password to activate the device when access the device via network. Note Refer to the user manual of the software client for the detailed information about the client software activation. Search and activate the online devices via SADP software. Before You Start Access www.hikvision.com to get SADP software to install. Steps 1. Connect the device to network using the network cable. 2.
Caution We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 5. Click OK. 6.
Temperature Measurement When you enable this function, the device measures the actual temperature of the scene. It alarms when temperature exceeds the temperature threshold value. This part introduces the notices of configuring temperature measurement function. ● The target surface should be as vertical to the optical axis as possible. It is recommended that the angle of oblique image plane should be less than 45°. ● The target image pixels should be more than 5 × 5.
● Top Left: display the information on the top left of screen. Add Original Data on Capture Check to add data on alarm triggered capture of thermal channel. Add Original Data on Stream Check to add original data on thermal view. Data Refresh Interval It means the refresh interval of temperature information. Unit Display temperature with Degree Celsius (°C)/Degree Fahrenheit (°F)/Degree Kelvin (K). Temperature Range Select the temperature measurement range. Version View the version of current algorithm. 4.
III. Set Expert Mode Select the temperature measurement rules from Point, Line, or Area and configure parameters, the device alarms if the alarm rules are met. Steps 1. Go to Configuration → Temperature Measurement → Basic Settings, check Enable Temperature Measurement. 2. Refer to Set Thermography Parameters to set the parameters. 3. Go to Configuration → Temperature Measurement → Advanced Settings, select Expert. 4. Select and enable the temperature measurement rules.
Set the tolerance temperature to prevent the constant temperature change to affect the alarm. E.g., set tolerance temperature as 3°C, set alarm temperature as 55°C, and set pre-alarm temperature as 50°C. The device sends pre-alarm when its temperature reaches 50°C and it alarms when its temperature reaches 55°C and only when the device temperature is lower than 52°C will the alarm be cancelled.
2. Click . 3. Drag the mouse in the live view to draw the area. You can drag the corners of the red rectangle area to change its shape and size. 4. Right click the mouse to stop drawing. 5. Optional: Select one area and click to delete it. 6. Click Save. After enable the manual thermography function of the device, you can click any position on the live view to show the real temperature. Steps 1. Go toConfiguration → Local and select Display Temperature Info. as Yes. 2.
27
Body Thermography Body Thermography function can detect temperature of human face or body in the scene, and output alarm if the temperature is higher than the setting value. Configure the parameters of body temperature measurement. Before You Start Go to Configuration → System → Maintenance → VCA Resource Type, select Body Thermography. Steps 1. Go to Configuration → Temperature Measurement → Basic Settings to configure parameters.
I. Measure Body Temperature in Thermal Channel Steps: 1. 2. 3. 4. Go to Configuration → Body Thermography → Body Thermography Configuration. Select thermal channel. Click Draw Area, then click the mouse on the black body in live view and save it. Set the black body parameters. Emissivity: Set the emissivity of black body. Note Refer to the emissivity table for reference in the manual or online. Distance: The straight-line distance between the black body and the device.
6. 7. Check Display Face Temperature Position to show a cursor on the position of max. temperature. Select Configuration mode. Targeting refers to measure the temperatures for all the targets in the scene, and output alarm if the target temperature is higher than the alarm threshold. Note If temperatures of multiple targets are higher than the alarm threshold, then multiple alarms will be triggered. 8. Set the face detection parameters.
II. Set Shield Region The shield region allows you to set the specific region in which the face capture does not work. Steps: 1. 2. Click to draw shield area by left click end-points in the live view window, and right click to finish the area drawing. Optional: Click to delete the drawn areas. Note You are allowed to draw up to 4 areas on the same image, and each area can be set with 3-10 points 3. Click Save. III.
Event and Alarm This part introduces the configuration of events. The device takes certain response to triggered alarm. It helps to detect the moving objects in the detection region and trigger the linkage actions. Steps 1. Go to Configuration → Event → Basic Event → Motion Detection. 2. Select the channel No. 3. Check Enable Motion Detection. 4. Optional: Highlight to display the moving object in the image in green. 1) Check Enable Dynamic Analysis for Motion. 2) Go to Configuration → Local.
4. Optional: You can set the parameters of multiple areas by repeating the above steps. II. Expert Mode You can configure the motion detection parameters of day/night switch according to the actual needs. Steps 1. Select expert mode in Configuration. 2. Set parameters of expert mode. Day/Night Switch OFF: Day/night switch is disabled. Day/Night Auto-Switch: The system switches day/night mode automatically according to environment. It displays colored image at day and black and white image at night.
4. Set the Sensitivity. The higher the value is, the easier to detect the area covering. 5. Click Draw Area and drag the mouse in the live view to draw the area. Stop Drawing Finish drawing. Clear All Delete all the drawn areas. Figure 6-3 Set Video Tampering Area 6. Refer to Set Arming Schedule for setting scheduled time. Refer to Linkage Method Settings for setting linkage method. 7. Click Save. Alarm signal from the external device triggers the corresponding actions of the current device.
Exception such as network disconnection can trigger the device to take corresponding action. Steps 1. Go to Configuration → Event → Basic Event → Exception. 2. Select Exception Type. HDD Full The HDD storage is full. HDD Error Error occurs in HDD. Network Disconnected The device is offline. IP Address Conflicted The IP address of current device is same as that of other device in the network. Illegal Login Incorrect user name or password is entered. 3.
Arming Schedule and Alarm Linkage Arming schedule is a customized time period in which the device performs certain tasks. Alarm linkage is the response to the detected certain incident or target during the scheduled time. Set the valid time of the device tasks. Steps 1. Click Arming Schedule. 2. Drag the time bar to draw desired valid time. Note Up to 8 periods can be configured for one day. 3. Adjust the time period. – Click on the selected time period, and enter the desired value. Click Save.
Delay Select Manual. 2. Click Manual Alarm to enable manual alarm output. 3. Optional: Click Clear Alarm to disable manual alarm output. Automatic Alarm Set the automatic alarm parameters, then the device triggers an alarm output automatically in the set arming schedule. Steps 1. Set automatic alarm parameters. Alarm Output No. Select the alarm output No. according to the alarm interface connected to the external alarm device. Alarm Name Custom a name for the alarm output.
Note If you want to use STARTTLS, make sure that the protocol is supported by your email server. If you check the Enable STARTTLS while the protocol is not supported by your email sever, your email is sent with no encryption. 4) Optional: If you want to receive notification with alarm pictures, check Attached Image. The notification email has 3 attached alarm pictures about the event with configurable image capturing interval. 5) Input the receiver's information, including the receiver's name and address.
The brightness of the light. 3. Edit the arming schedule. 4. Click Save. Note Only certain camera models support the function.
Live View It introduces the live view parameters, function icons and transmission parameters settings. Note For multichannel devices, select the desired channel first before live view settings. I. Window Division ● ● ● ● refers to 1 × 1 window division. refers to 2 × 2 window division. refers to 3 × 3 window division. refers to 4 × 4 window division. II. Live View Stream Type Select the live view stream type according to your needs.
VI. Full Screen This function is used to view the image in full screen mode. Click to start full screen mode and press ESC button to exit. VII. Light Click to turn on or turn off the illuminator. VIII. Wiper For the device that has a wiper, you can control the wiper via web browser. Click on live view page. The wiper wipes the window one time. IX. Lens Initialization Lens initialization is used on the device equipped with motorized lens.
XII. Lens Parameters Adjustment It is used to adjust the lens focus, zoom and iris. Zoom ● Click ● Click , and the lens zooms in. , and the lens zooms out. Focus ● Click ● Click , then the lens focuses far and the distant object gets clear. , then the lens focuses near and the nearby object gets clear. PTZ Speed Slide to adjust the speed of the pan/tilt movement. Iris ● When the image is too dark, click ● When the image is too bright, click to enlarge the iris. to stop down the iris.
The device ensures both the real-time video image and the fluency. Fluent The device takes the video fluency as the priority over teal-time. In poor network environment, the device cannot ensures video fluency even the fluency is enabled. Custom You can set the frame rate manually. In poor network environment, you can reduce the frame rate to get a fluent live view. But the rule information may cannot display. Auto Start Live View ● Yes means the live view is started automatically.
Video and Audio This part introduces the configuration of video and audio related parameters. This part introduces the settings of video parameters, such as, stream type, video encoding, and resolution. Go to setting page: Configuration → Video/Audio → Video. Note For device with multiple camera channels, select a channel before other settings. I. Stream Type For device supports more than one stream, you can specify parameters for each stream type.
Variable Bitrate It means that the device automatically adjust the bitrate under the set Max. Bitrate. The compression speed is slower than that of the constant bitrate. But it guarantees the image quality of complex scenes. V. Video Quality When Bitrate Type is set as Variable, video quality is configurable. Select a video quality according to actual needs. Note that higher video quality requires higher bandwidth. VI.
Scalable Video Coding (SVC) is the name for the Annex G extension of the H.264 or H.265 video compression standard. The objective of the SVC standardization has been to enable the encoding of a high-quality video bitstream that contains one or more subset bitstreams that can themselves be decoded with a complexity and reconstruction quality similar to that achieved using the existing H.264 or H.265 design with the same quantity of data as in the subset bitstream.
Set it as OFF or ON. When the function is enabled, the noise in the environment can be filtered to some extent. XI. Two-way Audio It is used to realize the two-way audio function between the monitoring center and the target in the monitoring screen. Before You Start ● Make sure the audio input device (pick-up or microphone) and audio output device (speaker) connected to the device is working properly. Refer to specifications of audio input and output devices for device connection.
I. Image Adjustment By adjusting the Brightness, Saturation, Contrast and Sharpness, the image can be best displayed. II. Image Adjustment (Thermal Channel) You can optimize the image display effect of thermal channel by setting background correction and manual correction. Background Correction Fully cover the lens with an object of uniform temperature in front of the lens, such as foam board or paperboard.
Note Day/Night Switch function varies according to models. V. Set Supplement Light Steps 1. Go to Configuration → Maintenance → System Service. 2. Check Enable Supplement Light. 3. Click Save. 4. Go to Configuration → Image → Display Settings → Day/Night Switch to set supplement light parameters. Smart Supplement Light This feature uses smart image processing technology to reduce overexposure caused by supplement light.
Expert Set the DNR level for both space DNR and time DNR to control the noise reduction degree. The higher level means stronger reduction degree. X. Set Palette You can select the palette mode to display the thermal grayscale image to colored image. Steps 1. Go to Configuration → Image → Display Settings. 2. Select the thermal channel. 3. Select a palette mode in Image Enhancement according to your need. Result The live view displays the image with palette. XI.
Figure 9-1 Set the Temperature and Color of Target Above (be colored) When the target of high temperature needs to be colored, you can set the high temperature color. Target above the setting temperature will be displayed in setting color. Between (be colored) When the target of an interval temperature needs to be colored, you can set the interval temperature color. Target between the minimum and the maximum temperatures will be displayed in setting color.
XII. DDE Digital Detail Enhancement is used to adjust the details of the image. OFF and Normal modes are selectable. OFF Disable this function. Normal Set the DDE level to control the details of the image. The higher the level is, the more details shows, but the higher the noise is. XIII. Brightness Sudden Change When the brightness of target and the background is hugely different (the temperature difference of target and background is huge), the system reduces the difference for viewing. XIV.
You can customize OSD (On-screen Display) information such as device name, time/date, font, color, and text overlay displayed on video stream. Go to OSD setting page: Configuration → Image → OSD Settings. Set the corresponding parameters, and click Save to take effect. Displayed Information Set camera name, date, week, and their related display format. Text Overlay Set customized overlay text on image. OSD Parameters Set OSD parameters, such as Display Mode, OSD Size, and Font Color.
If the amount of defective pixels in the image is comparatively small and accurate correction is needed, you can correct these pixels manually. Steps 1. Go to Configuration → Image → DPC. 2. Select the thermal channel. 3. Select manual mode. 4. Click the defective pixel on the image, then a cursor shows on the live view. 5. Click Up, Down, Left, Right to adjust the cursor position to the defective pixel position. 6. Click , then click to correct defective pixel.
Video Recording and Picture Capture This part introduces the operations of capturing video clips and snapshots, playback, and downloading captured files. This part introduces the configuration of several common storage paths. I. Set Memory Card If you choose to store the files to memory card, make sure you insert and format the memory card in advance. Before You Start Insert the memory card to the camera. For detailed installation, refer to Quick Start Guide of the camera. Steps 1.
Steps 1. Go to Configuration → Network → Advanced Settings → FTP. 2. Configure FTP settings. Server Address and Port The FTP server address and corresponding port. User Name and Password The FTP user should have the permission to upload pictures. If the FTP server supports picture uploading by anonymous users, you can check Anonymous to hide your device information during uploading. Directory Structure The saving path of snapshots in the FTP server. 3.
This part introduces the operations of manual and scheduled recording, playback, and downloading recorded files. I. Record Automatically This function can record video automatically during configured time periods. Before You Start Select Trigger Recording in event settings for each record type except Continuous. See Event and Alarm for details. Steps 1. Go to Configuration → Storage → Schedule Settings → Record Schedule. 2. Select channel No. 3. Check Enable. 4. Select a record type.
Note When you select the stream type with higher bitrate, the actual time of the pre-record and post-record may be less than the set value. 7. Click Save. II. Record Manually Steps 1. Go to Configuration → Local. 2. Set the Record File Size and saving path to for recorded files. 3. Click Save. 4. Click to start recording. Click to stop recording. III. Playback and Download Video You can search, playback and download the videos stored in the local storage or network storage. Steps 1. Click Playback. 2.
the snapshots. I. Capture Automatically This function can capture pictures automatically during configured time periods. Before You Start If event-triggered capture is required, you should configure related linkage methods in event settings. Refer to Event and Alarm for event settings. Steps 1. Go to Configuration → Storage → Schedule Settings → Capture → Capture Parameters. 2. Set the capture type. Timing Capture a picture at the configured time interval.
Network Settings TCP/IP settings must be properly configured before you operate the device over network. IPv4 and IPv6 are both supported. Both versions can be configured simultaneously without conflicting to each other. Go to Configuration → Basic Configuration → Network → TCP/IP for parameter settings. NIC Type Select a NIC (Network Interface Card) type according to your network condition. IPv4 Two IPv4 modes are available.
The device port can be modified when the device cannot access the network due to port conflicts. Caution Do not modify the default port parameters at will, otherwise the device may be unaccessible. Go to Configuration → Network → Basic Settings → Port for port settings. HTTP Port It refers to the port that access the device through the browser. You should enter the port No. after the IP address. For example, when the HTTP port is modified to 81, you need to enter http://192.168.1.
II. Set Manual Port Mapping Steps 1. Check Enable UPnP™, and choose a friendly name for the device, or you can use the default name. 2. Select the port mapping mode to Manual, and set the external port to be the same as the internal port. 3. Click Save. What to do next Go to the router port mapping settings interface and set the port number and IP address to be the same as those on the device. For more information, refer to the router user manual.
resolution server to realize the network access via domain name. Before You Start Registration on the DDNS server is required before configuring the DDNS settings of the device. Steps 1. Refer to TCP/IP to set DNS parameters. 2. Go to the DDNS settings page: Configuration → Network → Basic Settings → DDNS. 3. Check Enable DDNS and select DDNS type. DynDNS Dynamic DNS server is used for domain name resolution. NO-IP NO-IP server is used for domain name resolution. 4.
Note The obtained IP address is dynamically assigned via PPPoE, so the IP address always changes after rebooting the camera. To solve the inconvenience of the dynamic IP, you need to get a domain name from the DDNS provider (e.g. DynDns.com). Refer to Access to Device via Domain Name for detail information. Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or Web browser. I.
III. Access Camera via Hik-Connect Hik-Connect is an application for mobile devices. Using the App, you can view live image, receive alarm notification and so on. Steps 1. Download and install the Hik-Connect app by searching "Hik-Connect" in App Store or Google Play(TM) 2. Launch the app and register for a Hik-Connect user account. 3. Log in after registration. 4. In the app, tap "+" on the upper-right corner and then scan the QR code of the camera to add the camera.
Note Click Default to reset the destination IP or host name. 4. Click Save.
System and Security It introduces system maintenance, system settings and security management, and explains how to configure relevant parameters. You can view device information, such as Device No., Model, Serial No. and Firmware Version. Enter Configuration → System → System Settings → Basic Information to view the device information. Log helps locate and troubleshoot problems. Steps 1. Go to Configuration → System → Maintenance → Log. 2.
2. Click Restore or Default according to your needs. Restore Reset device parameters, except user information, IP parameters and video format to the default settings. Default Reset all the parameters to the factory default. Note Be careful when using this function. After resetting to the factory default, all the parameters are reset to the default settings. Before You Start You need to obtain the correct upgrade package.
5. Click Save. II. Set NTP Server You can use NTP server when accurate and reliable time source is required. Before You Start Set up a NTP server or obtain NTP server information. Steps 1. Go to Configuration → System → System Settings → Time Settings. 2. Select Time Zone. 3. Click NTP. 4. Set Server Address, NTP Port and Interval. Note Server Address is NTP server IP address. 5. Click Test to test server connection. 6. Click Save. III.
Steps 1. Go to Configuration → System → System Settings → RS-485. 2. Set the RS-485 parameters. Note You should keep the parameters of the device and the computer or terminal all the same. 3. Click Save. Set the same temperature unit and distance unit. When you enable this function, the unit cannot be configured separately in other setting pages Steps 1. Go to Configuration → System → System Settings → Unit Settings. 2. Check Use Same Unit. 3. Set the temperature unit and distance unit. 4. Click Save.
II. Security Audit Log The security audit logs refer to the security operation logs. You can search and analyze the security log files of the device so as to find out the illegal intrusion and troubleshoot the security events. Security audit logs can be saved on device internal storage. The log will be saved every half hour after device booting. Due to limited storage space, you can also save the logs on a log server.
IV. Set SSH SSH is a protocol to ensure security of remote login. This setting is reserved for professional maintenance personnel only. Steps 1. Go to Configuration → System → Security → Security Service. 2. Check Enable SSH. 3. Click Save. V. Set HTTPS HTTPS is a network protocol that enables encrypted transmission and identity authentication, which improves the security of remote access. Steps 1. Go to Configuration → Network → Advanced Settings → HTTPS. 2. Check Enable. 3.
VI. Set QoS QoS (Quality of Service) can help improve the network delay and network congestion by setting the priority of data sending. Note QoS needs support from network device such as router and switch. Steps 1. Go to Configuration → Network → Advanced Configuration → QoS. 2. Set Video/Audio DSCP, Alarm DSCP and Management DSCP. Note Network can identify the priority of data transmission. The bigger the DSCP value is, the higher the priority is.
Modify Select a user and click Modify to change the password and permission. Delete Select a user and click Delete. Note The administrator can add up to 31 user accounts. 3. Click OK.
Appendix No. 1 Symptom Description Unable to Boot The device cannot be normally started after installation 2 Screen off The LCD screen or digital board are off 3 No people counting The number of people displayed as 0001 or 0000. False Alarm The alarm is triggered when there is no people walk through 4 5 Omitting alarm No alarm when walk through the detector with metal Possible Reason 1.
Material Emissivity Wood 0.85 Pitch 0.96 Brick 0.95 Sand 0.90 Soil 0.92 Cloth 0.98 Hard Paperboard 0.90 White Paper 0.90 Water 0.
18 Zones 77
The smaller the histogram, the lower the sensitivity level required.
79
80
Detection Program PRG 01 USA PRG 02 USA HD PRG 03 CAN PRG 04 CAN HD Description Performance Optimizing High Pass Detection x x x x Distinguishability High U.S. airport security requirements x Canadian airport security x requirements PRG 05 GER German airport x PRG 06 GER HD security x x requirements PRG 07 UK The UK airport x PRG 08 UK HD security x x requirements PRG 09 USG U.S.
Thermal Imaging Sensor Max. Resolution Pixel Interval Response Waveband NETD Lens (Focal Length) MRAD Field of View Min. Focusing Distance Aperture Pseudo Color Visible Light Image frame Sensor Resolution Min.
Alarm input Alarm output Audio input （96/86/77/76）I series NVR Supports live view/playback, rule display, alarm report, and remote configuration Visible light: 50Hz: 25fps (1920 × 1080), 25fps (1280 × 960), 25fps (1280 × 720) Visible light: 60Hz: 30fps (1920 × 1080), 30fps (1280 × 960), 30fps (1280 × 720) Thermal Imaging: 25fps (160 × 120 (output320 × 240)) Visible light: 50Hz: 25fps (704 × 576), 25fps (640 × 480) Visible light: 60Hz: 30fps (704 × 480), 30fps (640 × 480) Thermal Imaging: 25fps (160 × 120 (
