Card Reader User Manual
Card Reader User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Card Reader User Manual Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of our devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
Card Reader User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Card Reader User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Card Reader User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
Card Reader User Manual • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. • Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. • Please keep all wrappers after unpack them for future use.
Card Reader User Manual Available Models Product Name: Card Reader Use only power supplies listed in the user instructions: Model TS-A018-120015Ec Manufacturer Shenzhen Transin Technologies CEE Co.
Card Reader User Manual Contents Chapter 1 Overview .................................................................................................................... 1 Chapter 2 Appearance ................................................................................................................ 2 2.1 Front View .............................................................................................................................. 2 2.2 Side View ..............................................
Card Reader User Manual Chapter 1 Overview The card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment.
Card Reader User Manual Chapter 2 Appearance 2.1 Front View The front view of the card reader is shown below: Figure 2-1 Front View 2.
Card Reader User Manual Figure 2-2 Side View 2.
Card Reader User Manual Table 2-1 Description of Rear View No. Name 1 Cable Interface of RS-485, Power, LED Control, etc.
Card Reader User Manual Chapter 3 Installation 3.1 Installing PSAM Card Note PSAM card slot is only available for CPU card reader. Insert the PSAM card into the slot according to the direction shown below. Figure 3-1 PSAM Card Slot 3.2 DIP Switch Description The DIP switch module is shown below. The No. of DIP switch from left to right is 1 to 8. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off.
Card Reader User Manual No. Description DIP Switch Status recognition function, disable door open via NFC card. 6 Wiegand protocol or RS-485 protocol. 1: Wiegand protocol 0: RS-485 protocol 7 Wiegand Protocol (available when No. 6 is 1) 1: Wiegand protocol of 26-bit 0: Wiegand protocol of 34-bit 8 Matched Resistance (available for RS-485 protocol) 1: Enable 0: Disable 3.3 Wiring Cables Wire the cables between controller and card reader, thus to establish the communication between them. 3.3.
Card Reader User Manual 3.3.2 Set RS-485 Communication Mode Steps 1. Set the DIP switch of No. 6 as 0. 2. Set the DIP switch of No. 1 ~ 5 for RS-485 address and reading card mode. For details, refers to DIP Switch Description . 3. Wire the cable between controller and card reader as shown below. Figure 3-2 Wiring for RS-485 Communication Mode 3.3.3 Set Wiegand Communication Mode Steps 1. Set the DIP switch of No. 6 as 1.
Card Reader User Manual 2. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, refers to DIP Switch Description . 3. Wiring the cable between controller and card reader as shown below. Figure 3-3 Wiring for Wiegand Communication Mode 3.4 Install Card Reader Before You Start Set the DIP switch. For details, refer to DIP Switch Description . Steps 1. Fix the plate on the wall or other place.
Card Reader User Manual Figure 3-4 Install Mounting Plate 2. Connect the cables between controller and card reader. For details, refer to Wiring Cables . 3. Push the card reader to match the fixed plate. 4. Fasten the screw to keep the components together.
Card Reader User Manual Chapter 4 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn blue and blink for 1 time. Then it will turn red and flash for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator on it will have different statuses. You can refer to tables below for detailed information.
Card Reader User Manual Appendix A. Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. • If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100 m, you are advised to power the card reader by external 12 V (range: -%10 to +%10) DC power supply, which is non-switched and linear.
UD18871N
