DS-K1109 Series Card Reader User Manual
DS-K1109 Series Card Reader User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1109 Series Card Reader User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1109 Series Card Reader User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1109 Series Card Reader User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
DS-K1109 Series Card Reader User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1109 Series Card Reader User Manual ● ● ● ● ● ● ● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
DS-K1109 Series Card Reader User Manual Available Models Product Name Card Reader Model Wireless DS-K1109DB 13.56 MHz Card Presenting Frequency, Bluetooth DS-K1109DKFB 13.56 MHz Card Presenting Frequency, Bluetooth DS-K1109DKFB-QR 13.56 MHz Card Presenting Frequency, Bluetooth DS-K1109DKB 13.56 MHz Card Presenting Frequency, Bluetooth DS-K1109DKB-QR 13.
DS-K1109 Series Card Reader User Manual Contents Chapter 1 Overview .................................................................................................................... 1 Chapter 2 Appearance ................................................................................................................ 2 2.1 Front View .............................................................................................................................. 2 2.2 Rear View ..............................
DS-K1109 Series Card Reader User Manual Chapter 1 Overview The card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment.
DS-K1109 Series Card Reader User Manual Chapter 2 Appearance 2.1 Front View The front view of card reader is shown below: Figure 2-1 Front View 2.
DS-K1109 Series Card Reader User Manual Figure 2-2 Rear View 3
DS-K1109 Series Card Reader User Manual Chapter 3 Installation 3.1 DIP Switch Description The DIP switch module is shown below. The No. of DIP switch from left to right is 1 to 8. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12. Table 3-1 Description of DIP Switch No.
DS-K1109 Series Card Reader User Manual 3.2 Wiring Cables Wire the cables between controller and card reader, thus to establish the communication between them. 3.2.1 Description of Cable The description of 10 cables is shown below.
DS-K1109 Series Card Reader User Manual Figure 3-1 Wiring for RS-485 Communication Mode 3.2.3 Set Wiegand Communication Mode Steps 1. Set the DIP switch of No. 6 as 1.
DS-K1109 Series Card Reader User Manual 2. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, refers to DIP Switch Description . 3. Wiring the cable between controller and card reader as shown below.
DS-K1109 Series Card Reader User Manual Chapter 4 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and flashing for 1 time. Then it will turn red and flashing for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator on it will have different statuses. You can refer to tables below for detailed information.
DS-K1109 Series Card Reader User Manual Appendix A. Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. ● ● ● ● ● ● ● ● If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100 m, you are advised to power the card reader by external 12 V (range: -%10 to +%10) DC power supply, which is non-switched and linear.
DS-K1109 Series Card Reader User Manual Appendix B. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure B-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD29976B
