DS-K1T320 Series Face Recogintion Terminal User Manual
DS-K1T320 Series Face Recogintion Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T320 Series Face Recogintion Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T320 Series Face Recogintion Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T320 Series Face Recogintion Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T320 Series Face Recogintion Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T320 Series Face Recogintion Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T320 Series Face Recogintion Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T320 Series Face Recogintion Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T320MFWX 13.56 MHz Card Presenting Frequency, Wi-Fi 2.4G DS-K1T320MFX 13.56 MHz Card Presenting Frequency DS-K1T320MWX 13.56 MHz Card Presenting Frequency, Wi-Fi 2.4G DS-K1T320MX 13.56 MHz Card Presenting Frequency DS-K1T320EFWX 125 KHz Card Presenting Frequency, Wi-Fi 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T320 Series Face Recogintion Terminal User Manual 7.1.1 Login by Administrator ................................................................................................ 24 7.1.2 Login by Activation Password ...................................................................................... 25 7.1.3 Forgot Password .......................................................................................................... 25 7.2 Communication Settings ............................................
DS-K1T320 Series Face Recogintion Terminal User Manual 7.9.2 Set Manual Attendance via Device ............................................................................. 43 7.9.3 Set Auto Attendance via Device .................................................................................. 44 7.9.4 Set Manual and Auto Attendance via Device .............................................................. 46 7.10 System Maintenance ............................................................................
DS-K1T320 Series Face Recogintion Terminal User Manual 14.2 Forget Password ................................................................................................................. 78 14.3 Live View ............................................................................................................................ 78 14.4 Person Management .......................................................................................................... 80 14.5 Search Event .........................
DS-K1T320 Series Face Recogintion Terminal User Manual 15.2.1 Add Device .............................................................................................................. 105 15.2.2 Reset Device Password ........................................................................................... 107 15.2.3 Manage Added Devices .......................................................................................... 108 15.3 Group Management ......................................................
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 17 Time Settings ........................................................................................................ 133 Chapter 18 Environment Settings ............................................................................................ 134 Chapter 19 Privacy Settings ..................................................................................................... 135 Chapter 20 Administrator Settings ..........................
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 2 Appearance The appearance of the device with fingerprint is as follows: Figure 2-1 Appearance（With Fingerprint) The appearance of the device without fingerprint is as follows: Figure 2-2 Appearance（Without Fingerprint) Table 2-1 Appearance Description No.
DS-K1T320 Series Face Recogintion Terminal User Manual No. Name Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● Indoor use only. Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight. 3.2 Install with Gang Box Steps 1. Make sure the gang box is installed on the wall.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 3-3 Apply Silicone Sealant 4. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-CM4X14-5T10-SUSS). Figure 3-4 Secure Device 3.3 Surface Mounting Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 3-5 Mounting Template 2. Drill holes on the wall or other surface according to the Hole 1 on the mounting template. 3. Remove the cable hole on the mounting plate with tools. 4. Align the holes to the mounting plate and secure the mounting plate on the wall with the 4 supplied screws (SC-KA4X22). Figure 3-6 Install Mounting Plate 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding peripherals cables.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 3-7 Apply Silicone Sealant 6. Align the device with the mounting plate and hang the device on the mounting plate. Use 1 supplied screw (SC-CM4X14_5T10-SUSS) to secure the device and the mounting plate. Figure 3-8 Hang Device 7. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.4 Base Mounting Steps 1.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 3-10 Fasten Bracket 3. Buckle into the bracket to the end to complete the installation.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 4 Wiring You can connect the NC/NO and COM terminal with the door lock, connect the SEN and GND terminal with the door contact and the BTN/GND terminal with the exit button. ● ● ● ● Note If cable size is 18 AWG, you should use a 12 V power supply. And the distance between the power supply and the device should be no more than 20 m. If the cable size is 15 AWG, you should use a 12 V power supply.
DS-K1T320 Series Face Recogintion Terminal User Manual 4.2 Wire Normal Device You can connect the terminal with normal peripherals. Figure 4-1 Device Wiring ● ● ● Note Do not wire the device to the electric supply directly. When connecting door contact and exit button, the device should use the same common ground connection.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T320 Series Face Recogintion Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T320 Series Face Recogintion Terminal User Manual Note Characters containing admin and nimda are not supported to be set as activation password. 3. Click Activate. 4. Edit the device IP address. You can edit the IP address via the SADP tool, the device, and the client software. 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.
DS-K1T320 Series Face Recogintion Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T320 Series Face Recogintion Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English.
DS-K1T320 Series Face Recogintion Terminal User Manual Note After you change the system language, the device will reboot automatically. 6.2 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-2 Welcome Page 2. Tap OK to save.
DS-K1T320 Series Face Recogintion Terminal User Manual ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T320 Series Face Recogintion Terminal User Manual Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 6-4 Access to Hik-Connect 2. Tap Next. Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected WiFi or connect another Wi-Fi to enter the platform page again. 6.5 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage.
DS-K1T320 Series Face Recogintion Terminal User Manual Select parameters according to your actual needs. Figure 6-5 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic.
DS-K1T320 Series Face Recogintion Terminal User Manual Before You Start Activate the device and select an application mode. Steps 1. Optional: Tap Skip to skip adding administrator if required. 2. Enter the administrator's name (optional) and tap Next. Figure 6-6 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm.
DS-K1T320 Series Face Recogintion Terminal User Manual / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . ● ● Enter the device room No. and tap OK to call. Tap to call the center.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long press OK to enter the admin login page. Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K1T320 Series Face Recogintion Terminal User Manual 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long press OK to enter Authenticate via Admin page. 2. to enter the password. Press - If you have added an administrator for the device, press OK and enter the password. - If you haven't added an administrator for the device, enter the password. 3.
DS-K1T320 Series Face Recogintion Terminal User Manual 2. On the Communication page, select Wired Network. Figure 7-2 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually. Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-3 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-4 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via ISUP protocol. Address Type Select an address type according to your actual needs. IP Set the ISUP server's IP address.
DS-K1T320 Series Face Recogintion Terminal User Manual If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key. You should enter the account name or the key when the device should communicate with other platforms via ISUP protocol. ISUP key range: 8 to 16 characters. 7.2.
DS-K1T320 Series Face Recogintion Terminal User Manual 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Select the Name field and input the user name on the keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 128 characters are allowed in the user name. 5.
DS-K1T320 Series Face Recogintion Terminal User Manual Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 8. Press ESC and then press OK to save the settings. 7.3.2 Add Face Picture Add user's face picture to the device. And the user can use the face picture to authenticate.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-5 Add Face Picture 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the center of the page. 7.
DS-K1T320 Series Face Recogintion Terminal User Manual Steps ● ● Note The function should be supported by the device. Up to 5000 fingerprints can be added. 1. Long press OK and login the device. 2. Press User → Add User to enter the Add User page. 3. Select the Employee ID field and edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not start with 0 and should not be duplicated.
DS-K1T320 Series Face Recogintion Terminal User Manual Steps Note The device supports MIFARE card, FILECA card, and DESfire card. 1. Long press OK and login the device. 2. Select User → Add User to enter the Add User page. 3. Select the Employee ID field and edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4.
DS-K1T320 Series Face Recogintion Terminal User Manual Steps 1. Long press OK and login the device. 2. Select User → Add User to enter the Add User page. 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Select the Name field and input the user name on the keyboard.
DS-K1T320 Series Face Recogintion Terminal User Manual Custom You can combine different authentication modes together according to your actual needs. 4. Press ESC to save the settings. 7.3.7 Edit User After adding the user, you can edit it. Edit User On the User Management page, select a user from the User List to enter the User Information page. Follow the steps in User Management to edit the user parameters. Press ESC to save the settings. Note The employee ID cannot be edited. 7.
DS-K1T320 Series Face Recogintion Terminal User Manual ● ● ● ● ● ● Note If you want to transfer all user information from one device (Device A) to another (Device B), you should export the information from Device A to the USB flash drive and then import from the USB flash drive to Device B. In this case, you should import the user data before importing the profile photo. The supported USB flash drive format is FAT32.
DS-K1T320 Series Face Recogintion Terminal User Manual 7.5.1 Authenticate via Single Credential Set the user authentication type before authentication. For details, see Set Authentication Mode . Authenticate face, fingerprint, card or PIN. Face Face forward at the camera and start authentication via face. Fingerprint Place the enrolled fingerprint on the fingerprint module and start authentication via fingerprint. Card Present the card on the card swiping area and start authentication via card.
DS-K1T320 Series Face Recogintion Terminal User Manual 7.6 Basic Settings You can set the voice, time, sleeping (s), language, supplement light, community No., building No., and unit No. Long press OK and login the device. Select Basic to enter System Settings page. Then select Basic to enter Basic Settings page. Figure 7-6 Basic Settings Page Voice Settings You can enable/disable the voice function. Time Settings Set the time zone, the device time and the DST.
DS-K1T320 Series Face Recogintion Terminal User Manual Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance. The configurable parameters includes application mode, face liveness level, face recognition distance, face recognition interval, face 1:N security level, face 1:1 security level and face with mask detection.
DS-K1T320 Series Face Recogintion Terminal User Manual Parameter Description Reminder of Wearing If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open. Must Wear If the person do not wear a face mask when authenticating, the device prompts a notification and the door keeps closed. None If the person do not wear a face mask when authenticating, the device will not prompt a notification. 7.
DS-K1T320 Series Face Recogintion Terminal User Manual Table 7-2 Access Control Parameters Descriptions Parameter Terminal Auth. Mode Description Select the face recognition terminal's authentication mode. You can also customize the authentication mode. ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-8 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-9 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 7-10 Auto Attendance Mode 3. Enable the Attendance Status Required function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Select Attendance Schedule.
DS-K1T320 Series Face Recogintion Terminal User Manual 7.9.4 Set Manual and Auto Attendance via Device Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Select T&A to enter the T&A Status page. 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Note The attendance status will be valid within the configured schedule. Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule. If you tap the edit icon on the result tab, you can select a status to take attendance manually, the authentication will be marked as the edited attendance status.
DS-K1T320 Series Face Recogintion Terminal User Manual Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of user, face picture, card, and event. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. Device Upgrade Plug the USB flash drive in the device USB interface. Select Upgrade → OK , and the device will read the digicap.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-1 Add User 50
DS-K1T320 Series Face Recogintion Terminal User Manual 2) Set the following parameters. Employee ID Enter the employee ID. The employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers. Name Enter the name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No. Enter the floor No./room No.
DS-K1T320 Series Face Recogintion Terminal User Manual Tap Configuration → System → System Settings → Basic Information , to enter the settings page.
DS-K1T320 Series Face Recogintion Terminal User Manual You can view the device name, device No., language, model, serial No., version, device capacity, etc. 8.4.2 Time Settings Set the time zone, time sync. mode, and displayed time. Tap Configuration → System → System Settings → Time Settings to enter the settings page. Figure 8-3 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-4 DST 2. Tap Enable DST. 3. Set the start time, end time, and DST bias. 4. Tap Save.
DS-K1T320 Series Face Recogintion Terminal User Manual 8.4.4 View Open Source Software License Tap Configuration → System → System Settings → About , and tap View Licenses to view the device license. 8.4.5 User Management Steps 1. Tap Configuration → System → User Management → admin → Modify Password to enter the setting page. 2. Enter the old password and create a new password. 3. Confirm the new password. 4. Tap OK. Note The password strength of the device can be automatically checked.
DS-K1T320 Series Face Recogintion Terminal User Manual The device will restore to the default settings, except for the device IP address and the user information. Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Unlink Tap Configuration → System → Maintenance . Tap Unlink to unlink the app. After unlinking APP account, you cannot operate via APP. 8.4.7 Security Settings You can set the SSH and HTTP according to actual needs.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-5 Wi-Fi 3. Add Wi-Fi.
DS-K1T320 Series Face Recogintion Terminal User Manual 1) Tap +. Figure 8-6 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type. 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters.
DS-K1T320 Series Face Recogintion Terminal User Manual 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 3) Tap Save. Set Port Parameters You can set the HTTP, RTSP, HTTPS, and Server according to actual needs when accessing the device via network.
DS-K1T320 Series Face Recogintion Terminal User Manual HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Tap Configuration → Network → Advanced → Hik-Connect to enter the settings page. Note Hik-Connect is an application for mobile devices.
DS-K1T320 Series Face Recogintion Terminal User Manual Main Channel/Backup Channel The device will communicate with the center via the main channel. When exception occurs in the main channel, the device and the center will communicate with each other via the backup channel. 5. Tap Save to save the settings. HTTP Listening You can set the HTTP listening parameters. Steps 1. Tap Configuration → Network → Advanced → HTTP Listening . 2. Edit the destination IP or domain name, URL and port. 3.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-7 Authentication Settings 2. Tap Save.
DS-K1T320 Series Face Recogintion Terminal User Manual You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max. Failed Attempts, Enable Tampering Detection and Enable Card No. Reversing. Card Reader Type Get card reader type.
DS-K1T320 Series Face Recogintion Terminal User Manual 64
DS-K1T320 Series Face Recogintion Terminal User Manual Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time.
DS-K1T320 Series Face Recogintion Terminal User Manual Clear Registered Face Pictures Select Face Picture, and tap Clear. All registered pictures in the device will be deleted. Clear Authentication/Captured Picture Select Authentication/Captured Picture, and tap Clear. All authentication/captured pictures in the device will be deleted. Set Card Security Tap Configuration → General Settings → Card Security to enter the settings page. Figure 8-9 Card Security Set the parameters and tap Save.
DS-K1T320 Series Face Recogintion Terminal User Manual Sector Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. Enable CPU Card The device can read the data from CPU card when enabling the CPU card function. Set Card Authentication Parameters Set the card reading content when authenticate via card on the device. Tap Configuration → General Settings → Card Authentication Settings .
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-11 Face Parameters 68
DS-K1T320 Series Face Recogintion Terminal User Manual Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Live Face Detection Security Level After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication.
DS-K1T320 Series Face Recogintion Terminal User Manual Configure the timeout period for face recognition. If the face recognition time exceeds the configured value, the device will prompt the face recognition timeout. Face with Mask Detection After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, its ECO mode, and the strategy.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 8-12 Door Parameters Settings Page Tap Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door.
DS-K1T320 Series Face Recogintion Terminal User Manual Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 9 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system from the drop-down list. By default, the system language is English. Note After you change the system language, the device will reboot automatically. Click Next to complete the settings.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 10 Time Settings Set Time and DST Click Wizzard → Time Settings . Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 11 Environment Settings After activating the device, you should select an application mode for better device application. Steps 1. Click Wizard → Environment Settings. 2. Select Indoor or Other. ● ● ● Note If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 12 Privacy Settings Set the picture uploading and storage parameters. Go to Wizard → Privacy Settings . Picture Uploading and Storage Save Picture When Authenticating Save picture when authenticating automatically. Upload Picture When Authenticating Upload the pictures when authenticating to the platform automatically. Save Registered Picture The registered face picture will be saved to the system if you enable the function.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 13 Administrator Settings Steps 1. Click Wizard → Administrator Settings . 2. Enter the employee ID and name of the administrator. 3. Select a credential to add. Note You should select at least one credential. 1) Click Add Face to upload a face picture from local storage. Note The uploaded picture should be within 200 K, in JPG、JPEG、PNG format. 2) Click Add Card to enter the Card No. and select the property of the card.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 14 Operation via Web Browser 14.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 14-1 Live View Page Function Descriptions: Door Status Click to view the device live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view.
DS-K1T320 Series Face Recogintion Terminal User Manual You can view the event Employee ID, Name, Card No., Event Type, Time, and Operation. You can also click View More to enter the search conditions, including the event type, employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. Person Information You can view the added and not added information of person face, card, and fingerprint.
DS-K1T320 Series Face Recogintion Terminal User Manual Click Save to save the settings. Authentication Settings Click Person Management → Add to enter the Add Person page. Set the authentication type. Click Save to save the settings. Add Card Click Person Management → Add to enter the Add Person page. Click Add Card, enter the Card No. and select the Property, and click Save to add the card. Click Save to save the settings.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 14-2 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 14.6 Configuration 14.6.1 Set Local Parameters Set the live view parameters, picture and clip settings. Set Live View Parameters Click Configuration → Local to enter the Local page.
DS-K1T320 Series Face Recogintion Terminal User Manual 14.6.3 Set Time Set the device's time zone, synchronization mode, server address, NTP port, and interval. Click Configuration → System → System Settings → Time Settings . Figure 14-3 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 14-4 DST Page 2. Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 14.6.5 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK. Caution The password strength of the device can be automatically checked.
DS-K1T320 Series Face Recogintion Terminal User Manual 14.6.7 Network Settings Set TCP/IP, port, Wi-Fi parameters, ISUP, and platform access. Note Some device models do not support Wi-Fi or mobile data settings. Refer to the actual products when configuration. Set Basic Network Parameters Click Configuration → Network → Network Settings → TCP/IP . Figure 14-5 TCP/IP Settings Page Set the parameters and click Save to save the settings. NIC Type Select a NIC type from the drop-down list.
DS-K1T320 Series Face Recogintion Terminal User Manual Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Network Settings → Wi-Fi . Figure 14-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's name, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4.
DS-K1T320 Series Face Recogintion Terminal User Manual HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. HTTP Listening The device can send alarm information to the event alarm IP address or domain name via HTTP protocol/HTTPS protocol.
DS-K1T320 Series Face Recogintion Terminal User Manual Set ISUP Parameters Set the ISUP parameters for accessing device via ISUP protocol. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Device Access → ISUP . 2. Check Enable. 3. Set the ISUP version, server address, device ID, and the ISUP status. Note If you select 5.0 as the version, you should set the encryption key as well. 4.
DS-K1T320 Series Face Recogintion Terminal User Manual Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval. Click Save to save the settings after the configuration. Note The functions vary according to different models. Refers to the actual device for details. 14.6.9 Set Image Parameters You can adjust the image parameters, video parameters, supplement parameters and capture interval. Steps 1. Click Configuration → Image . 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Note The functions vary according to different models. Refers to the actual device for details. Figure 14-8 Set Authentication Parameters Click Save to save the settings after the configuration. Terminal/Terminal Type/Terminal Model Get terminal description. They are read-only. Enable Authentication Device Enable the authentication function. Authentication Select an authentication mode according to your actual needs from the drop-down list.
DS-K1T320 Series Face Recogintion Terminal User Manual Tampering Detection Enable the anti-tamper detection for the card reader. Card No. Reversing The read card No. will be in reverse sequence after enabling the function. Set Door Parameters Click Configuration → Access Control → Door Parameters . Figure 14-9 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door.
DS-K1T320 Series Face Recogintion Terminal User Manual Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open. Door Lock Powering Off Status You can set the door lock status when the door lock is powering off. By default, it is Remain Closed. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended access needs swipes her/his card.
DS-K1T320 Series Face Recogintion Terminal User Manual In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption Sector M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13.
DS-K1T320 Series Face Recogintion Terminal User Manual Set a time and all events will be deleted on the configured time. Overwriting The earliest 5% events will be deleted when the system detects the stored events has been over 95% of the full space. Authentication Settings Display Authentication Result You can check Face Picture, Name, and Employee ID, to display the authentication result. Name De-identification You can check Name De-identification, and the whole name will not be displayed.
DS-K1T320 Series Face Recogintion Terminal User Manual schedule repeats, the shift type, break settings, and the card swiping rule.) to the shift group to define the attendance parameters for the persons in the shift group. Disable Attendance Mode via Web Disable the attendance mode and the system will not display the attendance status on the initial page. Steps 1. Click Configuration → T&A Status to enter the settings page. 2. Set the Time and Attendance.
DS-K1T320 Series Face Recogintion Terminal User Manual Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. Result You should select an attendance status manually after authentication. Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. Set Auto Attendance via Web Set the attendance mode as auto, and you can set the attendance status and its available schedule.
DS-K1T320 Series Face Recogintion Terminal User Manual 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule. Refers to Time Settings for details. Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 14-10 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T320 Series Face Recogintion Terminal User Manual Select either others or indoor according to actual environment. Face Recognition Mode Normal Mode Recognize face via the camera normally. Pitch Angle The maximum pitch angle when starting face authentication. Yaw Angle The maximum yaw angle when starting face authentication. 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode.
DS-K1T320 Series Face Recogintion Terminal User Manual Set Recognition Area Click Configuration → Smart → Area Configuration . Drag the yellow frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system. Click Save to save the settings. or to record videos or capture pictures. Click 14.6.15 Set Preference You can set the display theme and the sleep time for the device. Set Theme Click Configuration → Preference .
DS-K1T320 Series Face Recogintion Terminal User Manual Restore Parameters Click Maintenance and Security → Maintenance → Backup and Reset . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Restore The device will restore to the default settings, except for the device IP address and the user information. Import and Export Parameters Click Maintenance and Security → Maintenance → Backup and Reset .
DS-K1T320 Series Face Recogintion Terminal User Manual Set the major and minor type of the log type. Set the start time and end time for searching, and click Search. The results will be displayed below, which including the No., time, the major type the minor type, the channel No., the local/remote user information, the remote host IP, etc. 14.6.19 Security Mode Settings Set the security mode for logging in the client software.
DS-K1T320 Series Face Recogintion Terminal User Manual 2) Select a certificate type in the Import Communication Certificate area, and select a certificate from the local, and click Install. Install Other Authorized Certificate If you already has an authorized certificate (not created by the device), you can import it to the device directly. Steps 1. Go to Maintenance and Security → Security → Certificate Management . 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 15 Client Software Configuration 15.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 15-1 Flow Diagram of Configuration on Client Software 15.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T320 Series Face Recogintion Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 15.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T320 Series Face Recogintion Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T320 Series Face Recogintion Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T320 Series Face Recogintion Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T320 Series Face Recogintion Terminal User Manual 15.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T320 Series Face Recogintion Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 15.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 15.4.
DS-K1T320 Series Face Recogintion Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T320 Series Face Recogintion Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T320 Series Face Recogintion Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 15.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T320 Series Face Recogintion Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by Local Mode. 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. Click the Card No. column and enter the card number. 6. - Place the card on the card enrollment station.
DS-K1T320 Series Face Recogintion Terminal User Manual Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E.
DS-K1T320 Series Face Recogintion Terminal User Manual 15.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K1T320 Series Face Recogintion Terminal User Manual Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2.
DS-K1T320 Series Face Recogintion Terminal User Manual 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 15.
DS-K1T320 Series Face Recogintion Terminal User Manual Figure 15-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T320 Series Face Recogintion Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 15-3 Data Synchronization 15.
DS-K1T320 Series Face Recogintion Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T320 Series Face Recogintion Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K1T320 Series Face Recogintion Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached.
DS-K1T320 Series Face Recogintion Terminal User Manual ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T320 Series Face Recogintion Terminal User Manual View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T320 Series Face Recogintion Terminal User Manual 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T320 Series Face Recogintion Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T320 Series Face Recogintion Terminal User Manual 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. Steps Note This function should be supported by the device. 1. Enter the Access Control module. 2.
DS-K1T320 Series Face Recogintion Terminal User Manual 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 15.8 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device. You can also control the doors such as open/close the door, or remain the door open/closed via the client remotely.
DS-K1T320 Series Face Recogintion Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T320 Series Face Recogintion Terminal User Manual Steps 1. Click Monitoring and select a group from the drop-down list on the upper-right corner. The access records triggered at the doors in the selected group will display in real time. You can view the details of the records, including card No., person name, organization, event time, etc. 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 16 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system from the drop-down list. By default, the system language is English. Note After you change the system language, the device will reboot automatically. Click Next to complete the settings.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 17 Time Settings Set Time and DST Click Wizzard → Time Settings . Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 18 Environment Settings After activating the device, you should select an application mode for better device application. Steps 1. Click Wizard → Environment Settings. 2. Select Indoor or Other. ● ● ● Note If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 19 Privacy Settings Set the picture uploading and storage parameters. Go to Wizard → Privacy Settings . Picture Uploading and Storage Save Picture When Authenticating Save picture when authenticating automatically. Upload Picture When Authenticating Upload the pictures when authenticating to the platform automatically. Save Registered Picture The registered face picture will be saved to the system if you enable the function.
DS-K1T320 Series Face Recogintion Terminal User Manual Chapter 20 Administrator Settings Steps 1. Click Wizard → Administrator Settings . 2. Enter the employee ID and name of the administrator. 3. Select a credential to add. Note You should select at least one credential. 1) Click Add Face to upload a face picture from local storage. Note The uploaded picture should be within 200 K, in JPG、JPEG、PNG format. 2) Click Add Card to enter the Card No. and select the property of the card.
DS-K1T320 Series Face Recogintion Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T320 Series Face Recogintion Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T320 Series Face Recogintion Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T320 Series Face Recogintion Terminal User Manual Posture In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face pictures. Size Make sure your face is in the middle of the collecting window.
DS-K1T320 Series Face Recogintion Terminal User Manual Appendix C. Tips for Installation Environment 1.
DS-K1T320 Series Face Recogintion Terminal User Manual 2.
DS-K1T320 Series Face Recogintion Terminal User Manual Appendix D. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure D-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD28901B
