User's Manual

ManualsBrandsHIKVISION ManualsElectronicsFace Recognition Terminal

UD17592B

Wall Mounting:

The ﬁgures are for reference only.

You can also install the device on the wall or

other places without the gang box. For

details, refer to the User Manual.

Direct

Sunlight

Direct Sunlight

through Window

Backlight

Indirect Sunlight

through Window

Close to Light

Make sure the gang box is installed on the wall.

Align the device with the mounng

plate and hang the terminal on the

mounng plate.

Use 1 supplied screw (SC-KM3X6-H2-SUS)

to secure the device and the mounng plate.

Apply Silicone sealant among the joints

between the device rear panel and the

wall (except the lower side) to keep the

raindrop from entering.

Use 2 supplied screws (SC-K1M4×6-SUS) to secure the base plate

on the gang box.

Route the cables through the cable hole of the mounng plate,

and connect to the corresponding external devices’ cables.

Use another 4 supplied screws (KA4×22-SUS)to secure the

mounng plate on the base plate.

Installation Environment:

Indoor and outdoor installaon are supported. If installing the device

indoors, the device should be at least 2 meters away from the light, and at

least 3 meters away from the window or the door. If installing the device

outdoors, you should apply Silicone sealant among the device to keep the

raindrop from entering.

The addional force shall be equal to three mes the weight of the equipment

but not less than 50N. The equipment and its associated mounng means shall

remain secure during the installaon. Aer the installaon, the equipment, including

any associated mounng plate, shall not be damaged.

microUSB Interface

(Use micro USB to USB cable

to connect with USB interface)

CameraCamera

Debugging Port

(For debugging only)

Tamper

Wiring

Terminal

Network

Interface

Screen

IR Light IR Light

White Light

Card Presenng Area

Fingerprint

Module

(Supported by

parts of

Device Models)

22.7 mm

83.2 mm

12.3 mm

172.5 mm

Mic

DS-K1T341A Series

Face Recognition Terminal

Quick Start Guide

It includes instrucons on how to use the Product. The soware embodied in the Product is

governed by the user license agreement covering that Product.

About this Manual

This Manual is subject to domesc and internaonal copyright protecon. Hangzhou Hikvision

Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be

reproduced, changed, translated, or distributed, parally or wholly, by any means, without the

prior wrien permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are registered

trademarks or the subject of applicaons for the same by Hikvision and/or its aﬃliates. Other

trademarks menoned in this manual are the properes of their respecve owners. No right of

license is given to use such trademarks without express permission.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS

HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT

LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE,

AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,

OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,

INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF

BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN

CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY

AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER

ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL

PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS

THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS

USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER

PREVAILS.

Data Protecon

During the use of device, personal data will be collected, stored and processed. To protect data,

the development of Hikvision devices incorporates privacy by design principles. For example, for

device with facial recognion features, biometrics data is stored in your device with encrypon

method; for ﬁngerprint device, only ﬁngerprint template will be saved, which is impossible to

reconstruct a ﬁngerprint image.

As data controller, you are advised to collect, store, process and transfer data in accordance with

the applicable data protecon laws and regulaons, including without limitaon, conducng

security controls to safeguard personal data, such as, implemenng reasonable administrave and

physical security controls, conduct periodic reviews and assessments of the eﬀecveness of your

security controls.

Scan the QR code to get the user manual

for detailed informaon.

Note that mobile data charges may apply

if Wi-Fi is unavailable.

Use only power supplies listed in the user instrucons:

Make sure the power supply is used indoors, and the working

temperature is between 0 and 40 °C.

When connecng door magnec sensor and exit

buon, the device and the RS-485 card reader

should use the common ground connecon.

The Wiegand termimal here is a Wiegand input

terminal. You should set the face recognion

terminal’s Wiegand direcon to “Input”. If you

connect to an access controller, you should

set the Wiegand direcon to “Output”. For details,

see Seng Wiegand Parameters in Communicaon

Sengs in the user manual.

The suggested external power supply for door lock

is 12 V, 1A.

The suggested external power supply for Wiegand

card reader is 12 V, 1 A.

For wiring the ﬁre system, see the user manual.

If the interface for network connecon is too large,

you can use the supplied cable as shown below.

Connect

Network

Interface of

Device

Connect

Network

Cable

Model Manufacture Standard

ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG

MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PDE

ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd PB

ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd PCU

ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd PI

ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.,Ltd PBR

RS-485

Wiegand

Door Lock

Network Interface

Power Input

GND

BTN

12V External

Power Supply

Wiegand

Card Reader

Group B

Group D

(NC)

(COM)

(NO)

Eletric Dropbolt

Power Supply

Eletric Strike

Door Contact

Exit Button

White/Black

White/Purple

White/Yellow

White/Red

Yellow/Green

Yellow/Gray

Yellow/Black

Black

Red/Black

Black

Yellow

Green

White

Blue

Red

COM

Installation

Appearance

3.1

Device Wiring (Normal)

Loudspeaker

Summary of content (2 pages)

PAGE 1
2 Installation Appearance Loudspeaker Installation Environment: Indoor and outdoor installation are supported. If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. If installing the device outdoors, you should apply Silicone sealant among the device to keep the raindrop from entering. The additional force shall be equal to three times the weight of the equipment but not less than 50N.
PAGE 2
4 3.2 Device Wiring (With Secure Door Control Unit) Face Recognition Terminal Sensor Input RS-485 B1 Yellow B2 Blue B3 Red/Black 5 Secure Door Control Unit Secure Door Control Unit Wiring Terminal Exit Button Lock Output Power on and wire the network cable after installation. You should activate the device before the ﬁrst login.