User's Instructions

4
Activation
Two-Way Audio
5
Call Device from Client Software
Aer adding the device on the client soware, you can enter the Live View page. Right click the live
view window and click Start Two-Way Audio to start two-way audio.
Call Client Software from Device
Aer adding the device on the client soware, tap -> , and tap Answer on the pop-up window
on the client soware to start two-way audio.
If the device is added by mulple client sowares and when the device is calling the client soware, only
the first client soware added the device will pop up the call receiving window.
Call Indoor Station from Device
Aer adding the device and the indoor staon on the client soware, link the added user and the
added indoor staon, and set a room No. for the indoor staon.
Tap and enter the room No. And tap OK to call the indoor staon.
Call Center from Device
Aer adding the device and center on the client soware, tap -> to call the center. When the
center answers the call, you can start two-way audio.
The device will call the center in priority when tap the administrator icon.
Aer adding the device to the client soware, you can call the device from the client soware, call the client
soware from the device, call the center from the device, or call the indoor staon from the device.
The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A.
1. Use finger to hold the screen surface and enter the acvaon
password to enter the main page.
2. Enter the User Management page, tap + to enter the Add User
page.
3. Set the user parameters according to actual needs.
4. Tap Face and collect the face informaon according to the
instrucons.
You can view the captured picture at the upper right corner of
the page. Make sure the face picture is in good quality and size.
For details about the ps and posions when collecng or
comparing the face picture, see the contents on the right.
5. If the picture is in good condion, tap Save to save the picture.
Or tap Try Again to take another face picture.
6. Tap to save the sengs.
Go back to the inial page to start authencaon.
For other authencaon methods, see the device user manual.
Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m)
Tips When Collecting/
Comparing Face Picture
Expression
Posture
Size
1.4m
0.5m
1.4m
Too High
Too Low
Too Close
Too Far
1.4m
1.2m
1.4m
Make sure your face is in the middle of the collecng window.
Correct Tilt RaiseSide Bow
0.5m 0.5m
Recommended Height:
1.43m to 1.90m
Correct
Too Close Too Far
Only the devices with the fingerprint module support the
fingerprint related funcons.
Recommended:
Use other authencaon methods if the device if affected by the
light or other items.
1:N Matching: The device will compare the captured face picture
with the ones in the database.
1:1 Matching: The device will compare the captured face picture
with the user linked face picture.
Keep your expression naturally when collecng or
comparing face pictures, just like the expression in the
picture on the right.
In order to get a good quality and accurate face picture, posion your
face looking at the camera when collecng or comparing face pictures.
Do not wear hat, sunglasses, or other accessories that
can affect the facial recognion funcon.
Do not make your hair cover your eyes, ears, etc. and
heavy makeup is not allowed.
Power on and wire the network cable aer installaon. You
should acvate the device before the first login.
If the device is not acvated yet, it will enter the Acvate
Device page aer powering on.
Steps:
1. Create a password and confirm the password.
2. Tap Acvate to acvate the device.
For other acvaon methods, see the device user manual.
Sensor Input
Power Input
RS-485
SENSOR
BUTTON
B1
B2
B3
B4
Green/Brown
Door Contact
Black
Green/Black
Black
Lock Output
NC
C1
C2
C3
COM
(NC)
Power
(NO)
White/Purple
White/Black
White/Red
Exit Button
Face Recognition Terminal
NO
COM
NC
NO
COM
NC
Secure Door
Control Unit
Wiring Terminal
Electric
Dropbolt
Electric
Strike
Secure Door Control Unit
Red
Black
Exit Button
3.2
Device Wiring (With Secure Door Control Unit)
6
Add Face Picture
Biometric recognion products are not 100% applicable
to an-spoofing environments. If you require a higher
security level, use mulple authencaon modes.
Activate
Acvate Device
Enter Password
Comfirm Password
Comfirm password.
Enter 8 to 16 characters.
Enter 8 to 16 characters.
STRONG PASSWORD RECOMMENDED–
We highly recommend you create a strong password of your own
choosing (using a minimum of 8 characters, including upper case
leers, lower case leers, numbers, and special characters) in
order to increase the security of your product. And we
recommend you reset your password regularly, especially in the
high security system, reseng the password monthly or weekly
can beer protect your product.
GND
485-
485+
B1
B2
B3
Yellow
Blue
Red/Black
Regulatory Information
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards
listed under the RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the
RoHS Direcve 2011/65/EU.
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collecon points. For
more informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot be
disposed of as unsorted municipal waste in the European Union. See the
product documentaon for specific baery informaon. The baery is marked
with this symbol, which may include leering to indicate cadmium (Cd), lead
(Pb), or mercury (Hg). For proper recycling, return the baery to your supplier
or to a designated collecon point. For more informaon see: www.recycle-
this.info
FCC Conditions
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two
condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operaon.
EU Conformity Statement
FCC Information
Please take aenon that changes or modificaon not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
If the product does not work properly, please contact your dealer or the nearest service center.
Never aempt to disassemble the device yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
The socket-outlet shall be installed near the equipment and shall be easily accessible.
An all-pole mains switch shall be incorporated in the electrical installaon of the building.
The equipment has been designed, when required, modified for connecon to an IT power
distribuon system.
Do not ingest baery. Chemical burn hazard!
This product contains a coin/buon cell baery. If the coin/buon cell baery is swallowed, it
can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used baeries away from children.
If the baery compartment does not close securely, stop using the product and keep it away
from children.
If you think baeries might have been swallowed or placed inside any part of the body, seek
immediate medical aenon.
CAUTION: Risk of explosion if the baery is replaced by an incorrect type.
Improper replacement of the baery with an incorrect type may defeat a safeguard (for
example, in the case of some lithium baery types).
Do not dispose of the baery into fire or a hot oven, or mechanically crush or cut the baery,
which may result in an explosion.
Do not leave the baery in an extremely high temperature surrounding environment, which
may result in an explosion or the leakage of flammable liquid or gas.
Do not subject the baery to extremely low air pressure, which may result in an explosion or
the leakage of flammable liquid or gas.
Dispose of used baeries according to the instrucons
This equipment is not suitable for use in locaons where children are likely to be present.
This equipment is for use only with DS-K1T341 mounng plate, bracket. Use with other (carts,
stands, or carriers) may result in instability causing injury.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Cauons
No naked flame sources, such as lighted candles, should be placed on the equipment
The USB port of the equipment is used for connecng to a mouse, a keyboard, or a USB flash
drive only.
The serial port of the equipment is used for debugging only.
Burned fingers when handling the back panel. Wait one-half hour aer switching off before
handling the parts.
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnesm radiaon. Avoid the equipment installaon on vibraons surface or places
subject to shock (ignorance can cause equipment damage).
Install the equipment according to the instrucons in this manual.
To prevent injury, this equipment must be securely aached to the floor/wall in accordance
with the installaon instrucons.
Do not place the device in extremely hot (refer to the specificaon of the device for the
detailed operang temperature), cold, dusty or damp locaons, and do not expose it to high
electromagnec radiaon.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfuncon however), and affecng the endurance of sensor at the
same me.
Please use the provided glove when open up the device cover, avoid direct contact with the
device cover, because the acidic sweat of the fingers may erode the surface coang of the device
cover.
Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do
not use alkaline detergents.
Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportaon without the
original wrapper may result in damage on the device and lead to addional costs.
Improper use or replacement of the baery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used baeries according to the instrucons provided by
the baery manufacturer.
Biometric recognion products are not 100% applicable to an-spoofing environments. If you
require a higher security level, use mulple authencaon modes.
Indoor and outdoor use. If installing the device indoors, the device should be at least 2 meters
away from the light, and at least 3 meters away from the window or the door. If installing the
device outdoors, you should apply Silicone sealant among the cable wiring area to keep the
raindrop from entering.
Safety Instrucon
These instrucons are intended to ensure that user can use the product correctly to avoid
danger or property loss.
The precauon measure is divided into Warnings and Cauons:
Warnings: Neglecng any of the warnings may cause serious injury or death.
Cauons: Neglecng any of the cauons may cause injury or equipment damage.
Warnings
In the use of the product, you must be in strict compliance with the electrical safety
regulaons of the naon and region.
Please use the power adapter, which is provided by normal company. The power
consumpon cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.