DS-K1T342 Series Face Recognition Terminal User Manual
DS-K1T342 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T342 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T342 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T342 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T342 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T342 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T342 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T342 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T342MX 13.56 MHz Card Presenting Frequency DS-K1T342MWX 13.56 MHz Card Presenting Frequency, Wi-Fi (2.4 GHz) DS-K1T342MFX 13.56 MHz Card Presenting Frequency DS-K1T342MFWX 13.56 MHz Card Presenting Frequency, Wi-Fi (2.4 GHz) DS-K1T342EX 125 KHz Card Presenting Frequency DS-K1T342EWX 125 KHz Card Presenting Frequency, Wi-Fi (2.
DS-K1T342 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation ....................................................................................................... 33 6.1 Select Language ................................................................................................................... 33 6.2 Set Application Mode .......................................................................................................... 35 6.3 Set Network Parameters .......................
DS-K1T342 Series Face Recognition Terminal User Manual 7.4 Data Management ............................................................................................................... 70 7.4.1 Delete Data ................................................................................................................. 70 7.4.2 Import Data ................................................................................................................. 70 7.4.3 Export Data ..................................
DS-K1T342 Series Face Recognition Terminal User Manual 8.4.7 Video Intercom Settings ............................................................................................ 108 8.4.8 Access Control Settings ............................................................................................. 110 Chapter 9 Operation via Web Browser .................................................................................... 116 9.1 Login ...................................................................
DS-K1T342 Series Face Recognition Terminal User Manual 9.5.21 Set Biometric Parameters ....................................................................................... 147 9.5.22 Set Notice Publication ............................................................................................. 151 Chapter 10 Client Software Configuration ............................................................................... 154 10.1 Configuration Flow of Client Software .....................................
DS-K1T342 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint ............................................................................... 182 Appendix B. Tips When Collecting/Comparing Face Picture .................................................... 184 Appendix C. Tips for Installation Environment ........................................................................ 186 Appendix D. Dimension .........................................................................
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● ● ● ● ● ● ● 4.3-inch LCD touch screen, 272 × 480 screen resolution, real-time detection and display of the maximum face frame.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 2 Appearance Figure 2-1 With Fingerprint Module Table 2-1 Appearance Description No.
DS-K1T342 Series Face Recognition Terminal User Manual No. Name 10 Wiring Terminal 11 Network Interface 12 Tamper Figure 2-2 Without Fingerprint Module Table 2-2 Appearance Description No.
DS-K1T342 Series Face Recognition Terminal User Manual No.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-1 Install Gang Box 2. Secure the mounting plate on the gang box with two supplied screws (SC-KA4X22). Figure 3-2 Install Mounting Plate 3. Route the cable through the cable hole, wire the cables and insert the cables in the gang box.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-3 Apply Silicone Sealant 4. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-KM3X6-T10-SUSS).
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-4 Secure Device 3.3 Surface Mounting Steps 1. According to the datum line on the mounting template, stick the mounting template on the wall or other surfaces, 1.45 meters higher than the ground.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-5 Mounting Template 2. Drill holes on the wall or other surface according to the Hole 1 on the mounting template. 3. Insert the plastic sleeve of expansion bolts into the holes. 4. Align the holes to the mounting plate and secure the mounting plate on the wall with the 2 supplied screws (KA4×22-SUS).
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-6 Install Mounting Plate 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding peripherals cables. Note If the device is installed outdoor, you should apply silicone sealant to the wiring exit to avoid water from entering.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-7 Apply Silicone Sealant 6. Align the device with the mounting plate and hang the device on the mounting plate.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-8 Hang Device 7. Use 1 supplied screw (KM3×6-SUS) to secure the device and the mounting plate.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-9 Secure Device Note ● The recommended installation height is 1.45 meters, you can set the installtion height according your needs. ● It's recommended to use the supplied mounting plate. 8. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.
DS-K1T342 Series Face Recognition Terminal User Manual 3.4 Mount With Bracket 3.4.1 Preparation before Mounting with Bracket Steps 1. Drill holes on the turnstile's surface according to the figure displayed below. And install waterproof nut. Note Solder after pressing rivets to avoid water from entering. Figure 3-10 Drill Holes on Turnstile 2. If the installation angle needs to be 180° perpendicular to the body of the turnstile, the following operations are required.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-12 Rotate Fixed Part 3.4.2 Mount Bracket Steps 1. Install the base on the turnstile. 1) Align the hole on the turnstile and place the base on the turnstile. 2) Rotate the base to the acquired place and make sure the device will face a correct direction. 3) Secure the base with wrench. Figure 3-13 Install Base Note Install a piece of silicone pad on the front and back of the turnstile. 2.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-14 Secure Mounting Template 3. Route the cables through the cable hole on the turnstile and fix the device into the mounting plate with 1 SC-KM3×6-T10-SUS screw. Figure 3-15 Fix the Device 4. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.5 Mount With Cylinder Bracket 3.5.
DS-K1T342 Series Face Recognition Terminal User Manual Note Solder after pressing rivets to avoid water from entering. Figure 3-16 Drill Holes on Turnstile 3. Solder the other four holes, polish the surface, and implement wire drawing. 4. Solder circular tubes on the turnstile’s inner surface to avoid water from entering.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-17 Solder Tubes 3.5.2 Cylinder Bracket Mounting Steps 1. Install the base on the turnstile. 1) Align the hole on the turnstile and place the base on the turnstile. 2) Rotate the base to the acquired place and make sure the device will face a correct direction. 3) Secure the base with 4 SC-OM6×12-H-SUS screws. Figure 3-18 Install Base 2. Fix the mounting plate into the bracket by 4 SC-K1M4×6-SUS screws.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 3-19 Fix Mounting Plate 3. Route the cables through the cable hole on the turnstile. 4. Fix the face recognition terminal into the mounting plate with 1 SC-KM3×6-H2-SUS screw. Figure 3-20 Fix Mounting Plate 5. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC/NO and COM terminal with the door lock, connect the SEN and GND terminal with the door contact, the BTN/GND terminal with the exit button, and connect the Wiegand terminal with the Wiegand card reader or the access controller.
DS-K1T342 Series Face Recognition Terminal User Manual Group Group D No. Function Color Name Description C2 White W1 Wiegand Wiring 1 C3 Black GND Ground White/Purple NC Lock Wiring (NC) D2 White/Yellow COM Common D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Grey BUTTON Exit Door Wiring D1 Door Lock 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 4-1 Device Wiring ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly. 4.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 4-2 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module 4.4.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 4-3 Wire Device Figure 4-4 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 4-5 Wiring Device Figure 4-6 Wiring Secure Door Control Unit 4.4.
DS-K1T342 Series Face Recognition Terminal User Manual ● ● Note The Uninterpretable Power Supply (UPS) is required. The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked.
DS-K1T342 Series Face Recognition Terminal User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
DS-K1T342 Series Face Recognition Terminal User Manual 4. Edit the device IP address. You can edit the IP address via the SADP tool, the device, and the client software. 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts.
DS-K1T342 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T342 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 6-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically.
DS-K1T342 Series Face Recognition Terminal User Manual 6.2 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K1T342 Series Face Recognition Terminal User Manual 2. Tap OK to save. ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 6-3 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next.
DS-K1T342 Series Face Recognition Terminal User Manual Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 6-4 Access to Hik-Connect 2. Tap Next. Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected WiFi or connect another Wi-Fi to enter the platform page again.
DS-K1T342 Series Face Recognition Terminal User Manual 6.5 Link to Mobile Client After activation, selecting application mode, selecting networking, you can add the device to the mobile client. Download and install the mobile client. Use the scan QR code function of the mobile client and scan the QR code displayed on the device to link the device to the mobile client. Follow the instructions to link the device to the mobile client.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 6-5 Link to Mobile Client 6.6 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage.
DS-K1T342 Series Face Recognition Terminal User Manual Select parameters according to your actual needs. Figure 6-6 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device.
DS-K1T342 Series Face Recognition Terminal User Manual Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function. Upload Pic. After Linked Capture (Upload Picture After Linked Capture) Upload the pictures captured by linked camera to the platform automatically. Save Pic. After Linked Capture (Save Pictures After Linked Capture) If you enable this function, you can save the picture captured by linked camera to the device.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 6-7 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added.
DS-K1T342 Series Face Recognition Terminal User Manual : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. 4. Click OK. You will enter the authentication page. Status Icon Description / Device is armed/not armed. / Hik-Connect is enabled/disabled.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page.
DS-K1T342 Series Face Recognition Terminal User Manual 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Enter the password. - If you have added an administrator for the device, tap and enter the password.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-3 Home Page 7.1.3 Forgot Password If you forget the password during authentication, you can reset the password by importing the key.
DS-K1T342 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the page. 2. Tap in the pop-up admin authentication page. 3. Plug USB flash drive into the USB interface. Note ● The supported USB flash drive formats are FAT32 and exfat. ● The device supports 1 G to 32 G (including 1 G and 32 G) USB flash drive. Make sure that the free space of the USB flash drive is more than 512 M. 4.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually.
DS-K1T342 Series Face Recognition Terminal User Manual Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK.
DS-K1T342 Series Face Recognition Terminal User Manual Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-6 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs.
DS-K1T342 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 4. Tap the back icon at the upper left corner and you should reboot the device if you change the parameters. 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or Wiegand 34. to save the network parameters. 5.
DS-K1T342 Series Face Recognition Terminal User Manual Note If you change the external device, and after you save the device parameters, the device will reboot automatically. 7.2.5 Set ISUP Parameters Set ISUP parameters and the device can upload data via ISUP protocol. Before You Start Make sure your device has connect to a network. Steps 1. Tap Comm. → ISUP .
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-8 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group.
DS-K1T342 Series Face Recognition Terminal User Manual Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via EHome protocol. Address Type Select an address type according to your actual needs. IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. Password If you choose V5.0, you should create an account and ISUP key.
DS-K1T342 Series Face Recognition Terminal User Manual 7.3 User Management On the user management interface, you can add, edit, delete and search the user. 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page.
DS-K1T342 Series Face Recognition Terminal User Manual 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard.
DS-K1T342 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5. Optional: Add a face picture, fingerprints, cards, or Pin for the administrator. ● Note For details about adding a face picture, see Add Face Picture . ● Note For details about adding a fingerprint, see Add Fingerprint . ● For details about adding a card, see Add Card .
DS-K1T342 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Face Picture field to enter the face picture adding page.
DS-K1T342 Series Face Recognition Terminal User Manual 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page. 7.
DS-K1T342 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Fingerprint field to enter the Add Fingerprint page. 6. Follow the instructions to add a fingerprint. Note ● The same fingerprint cannot be repeatedly added. ● Up to 10 fingerprints can be added for one user.
DS-K1T342 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 6. Tap the Card field and tap +. 7. Configure the card No. - Enter the card No. manually. - Present the card over the card presenting area to get the card No. Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8.
DS-K1T342 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the PIN code to view the PIN code. Note The PIN code cannot be edited. It can only be applied by the platform. 6. Set the user role. Administrator The user is the administrator.
DS-K1T342 Series Face Recognition Terminal User Manual Search User On the User Management page, Tap the search area to enter the Search User page. Tap Card on the left of the page and select a search type from the drop-down list. Enter the employee ID, card No., or the user name for search. Tap to search. Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow the steps in User Management to edit the user parameters. Tap to save the settings.
DS-K1T342 Series Face Recognition Terminal User Manual ● ● ● ● The imported pictures should be saved in the folder (named enroll_pic) of the root directory and the picture's name should be follow the rule below: Card No._Name_Department_Employee ID_Gender.jpg If the folder enroll_pic cannot save all imported pictures, you can create another folders, named enroll_pic1, enroll_pic2, enroll_pic3, enroll_pic4, under the root directory. The employee ID should be less than 32 characters.
DS-K1T342 Series Face Recognition Terminal User Manual Face forward at the camera and start authentication via face. Fingerprint Place the enrolled fingerprint on the fingerprint module and start authentication via fingerprint. Card Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. PIN Code Enter the pin code to authenticate via PIN code. If authentication completed, a prompt "Authenticated" will pop up. 7.5.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-10 Basic Settings Page Voice Settings You can enable/disable the voice prompt function and adjust the voice volume. Note You can set the voice volume between 0 and 10.
DS-K1T342 Series Face Recognition Terminal User Manual Time Settings Set the time zone, the device time and the DST. Sleeping (s) Set the device sleeping waiting time (minute). When you are on the initial page and if you set the sleeping time to 30 min, the device will sleep after 30 min without any operation. Note If you set the sleeping time to 0, the device will not enter sleeping mode. Select Language Select the language according to actual needs. Community No. Set the device installed community No.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-11 Biometric Parameters Page 75
DS-K1T342 Series Face Recognition Terminal User Manual Table 7-1 Face Picture Parameters Parameter Description Select Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K1T342 Series Face Recognition Terminal User Manual Parameter Description Set the matching value when authenticating with face mask via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask & Face (1:N ECO) Set the matching value when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-12 Access Control Parameters The available parameters descriptions are as follows: 78
DS-K1T342 Series Face Recognition Terminal User Manual Table 7-2 Access Control Parameters Descriptions Parameter Description Terminal Auth. Mode (Terminal Select the face recognition terminal's authentication mode. You Authentication Mode) can also customize the authentication mode. ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T342 Series Face Recognition Terminal User Manual 7.9.1 Disable Attendance Mode via Device Disable the attendance mode and the system will not display the attendance status on the initial page. Tap T&A Status to enter the T&A Status page.
DS-K1T342 Series Face Recognition Terminal User Manual Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required.
DS-K1T342 Series Face Recognition Terminal User Manual The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication. Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. 7.9.3 Set Auto Attendance via Device Set the attendance mode as auto, and you can set the attendance status and its available schedule.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-15 Auto Attendance Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required.
DS-K1T342 Series Face Recognition Terminal User Manual The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap Confirm. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-16 Manual and Auto Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required.
DS-K1T342 Series Face Recognition Terminal User Manual The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap OK. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-17 Preference Settings Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function.
DS-K1T342 Series Face Recognition Terminal User Manual Note You can select call type from Call Room, Call Center, Call Specified Room No. and Call APP. Call Room When you tap the call button on the authentication page, you should dial a room No. to call. Call Center When you tap the call button on the authentication page, you can call the center directly. Call Specified Room No. You should set a room No.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 7-18 Maintenance Page System Information You can view the device information including serial No., firmware version, MCU version, MAC address, production data, device QR code, open source code license.
DS-K1T342 Series Face Recognition Terminal User Manual Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of administrator, user, face picture, card, and event. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. Upgrade Plug the USB flash drive in the device USB interface. Tap Upgrade → OK , and the device will read the digicap.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-1 Add User 2) Set the following parameters. Employee ID Enter the employee ID. The Employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers.
DS-K1T342 Series Face Recognition Terminal User Manual Enter your name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No. Enter the floor No./room No. Face Add Face picture. Tap Face, then tapImport, and select the mode to import the face. Fingerprint Add fingerprint. Tap Fingerprint, then tap +, and add fingerprint via the fingerprint module.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-2 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync. Mode Manual By default, the device time should be synchronized manually. You can set the device time manually. NTP Set the NTP server's IP address, port No., and interval. 8.4.
DS-K1T342 Series Face Recognition Terminal User Manual Set Port Parameters You can set the HTTP, RTSP, HTTPS, and Server according to actual needs when accessing the device via network. Tap Configuration → Network → Basic Settings → Port , to enter the settings page. HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-3 Wi-Fi 3. Add Wi-Fi. 1) Tap +.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-4 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type. 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters. 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Tap Save. 8.4.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-5 Authentication Settings 2. Tap Save.
DS-K1T342 Series Face Recognition Terminal User Manual Device Type Main Card Reader You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max. Failed Attempts, Enable Tampering Detection and Enable Card No. Reversing.
DS-K1T342 Series Face Recognition Terminal User Manual Communication with Controller Every (s) When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max. Interval When Entering Password (s) When you entering the password on the card reader, if the interval between pressing two digits is longer than the set value, the digits you pressed before will be cleared automatically.
DS-K1T342 Series Face Recognition Terminal User Manual Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time. Overwriting The earliest 5% events will be deleted when the system detects the stored events has been over 95% of the full space. Authentication Settings Display Authentication Result Check Face Picture, Name, or Employee ID. When authentication is completed, the system will display the selected contents in the result.
DS-K1T342 Series Face Recognition Terminal User Manual Set Card Security Tap Configuration → General Settings → Card Security to enter the settings page. Figure 8-7 Card Security Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticateing by presenting M1 card is available.
DS-K1T342 Series Face Recognition Terminal User Manual Enable EM card and authenticating by presenting EM card is available. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. Enable CPU Card The device can read the data from CPU card when enabling the CPU card function. CPU Card Read Content After enable the CPU card content reading function, the device can read the CPU card content.
DS-K1T342 Series Face Recognition Terminal User Manual Face Parameters Settings Tap Configuration → Smart → Intelligent Parameter . Figure 8-9 Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T342 Series Face Recognition Terminal User Manual Select Indoor or Others according to actual environment. In the outdoor scene, indoor scene near the window, or bad environment, you can choose Others. Note If the device is not activated by other tools, the device uses indoor as the environment mode by default. Face Recognition Mode Normal Mode The device uses a camera to perform face recognition. Deep Mode It is applicable for for more complex environments, and the range of people recognized is wider.
DS-K1T342 Series Face Recognition Terminal User Manual After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, its ECO mode, and the strategy. None If the person do not wear a face mask when authenticating, the device will not prompt a notification. Reminder of Wearing If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open.
DS-K1T342 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100. Set Recognition Area Tap Configuration → Smart → Area Configuration to enter the page. Drag the blue frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system.
DS-K1T342 Series Face Recognition Terminal User Manual Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. If you set the device type as Outer Door Station, you can set the outer door station No. Figure 8-11 Device ID Settings (Outer Door Station) Outer Door Station No.
DS-K1T342 Series Face Recognition Terminal User Manual Note Only the access control device and other devices or systems (such as door station, indoor station, main station, platform) are in the same IP segment, the two-way audio can be performed. Tap Configuration → Intercom → Linked Network Settings . Figure 8-12 Linked Network Settings Set the video intercom server IP and main station's IP. Tap Save. Press Button to Call Steps 1.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 8-13 Door Parameters Settings Page 111
DS-K1T342 Series Face Recognition Terminal User Manual Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration.
DS-K1T342 Series Face Recognition Terminal User Manual Tap Configuration → Access Control → RS-485 . Figure 8-14 RS-485 Page Tap Save to save the settings after the configuration. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, or Access Controller. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T342 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. Baud Rate The baud rate when the devices are communicating via the RS-485 protocol. Data Bit The data bit when the devices are communicating via the RS-485 protocol.
DS-K1T342 Series Face Recognition Terminal User Manual The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 9 Operation via Web Browser 9.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-1 Live View Page Function Descriptions: Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view.
DS-K1T342 Series Face Recognition Terminal User Manual Full screen view. 9.3 Person Management Click and add the person's information, including the basic information, authentication mode, card and fingerprint. And you can also edit user information, view user picture and search user information in the user list. Click OK to save the person. Add Basic Information Click User → Add to enter the Add Person page.
DS-K1T342 Series Face Recognition Terminal User Manual After check Administrator in Access Control, the added person can log in by authenticating face. You can click Add to enter the Floor No. and Room No. of access control, and click to delete it. Click OK to save the settings. Add Authentication Mode Click User → Add to enter the Add Person page. Set the authentication type. Click OK to save the settings. 9.4 Search Event Click Search to enter the Search page.
DS-K1T342 Series Face Recognition Terminal User Manual Set Live View Parameters Click Configuration → Local to enter the Local page. Configure the stream type, the play performance, auto start live view, and the image format and click Save. Set Record File Saving Path Click Configuration → Local to enter the Local page. Select a record file size and select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-3 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 9.5.4 Set DST Steps 1.
DS-K1T342 Series Face Recognition Terminal User Manual 4. Click Save to save the settings. 9.5.5 View Open Source Software License Go to Configuration → System → System Settings → About , and click View Licenses to view the device license. 9.5.6 Upgrade and Maintenance Reboot device, restore device parameters, and upgrade device version. Reboot Device Click Configuration → System → Maintenance → Upgrade & Maintenance . Figure 9-5 Upgrade and Maintenance Page Click Reboot to start reboot the device.
DS-K1T342 Series Face Recognition Terminal User Manual Default The device will restore to the default settings, except for the device IP address and the user information. Unlink APP Account Unlink the Hik-Connect account from the platform. Import and Export Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Export Click Export to export the logs or device parameters. Note You can import the exported device parameters to another device.
DS-K1T342 Series Face Recognition Terminal User Manual Select a security mode from the drop-down list, and click Save. Security Mode High security level for user information verification when logging in the client software. Compatible Mode The user information verification is compatible with the old client software version when logging in. Enable SSH To raise network security, disable SSH service. The configuration is only used to debug the device for the professionals.
DS-K1T342 Series Face Recognition Terminal User Manual Install Other Authorized Certificate If you already has an authorized certificate (not created by the device), you can import it to the device directly. Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Import Passwords and Import Communication Certificate areas, select certificate type and upload certificate. 3. Click Install. Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1.
DS-K1T342 Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 9.5.11 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → Arming/Disarming Information . You can view the device arming/disarming information. Click Refresh to refresh the page. 9.5.
DS-K1T342 Series Face Recognition Terminal User Manual RTSP It refers to the port of real-time streaming protocol. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device. Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . Figure 9-6 Wi-Fi Settings Page 2.
DS-K1T342 Series Face Recognition Terminal User Manual 2) Set the IP address, subnet mask, and default gateway. Or check Enable DHCP and the system will allocate the IP address, subnet mask, and default gateway automatically. 5. Click OK. Report Strategy Settings You can set the center group for uploading the log via the ISUP protocol. Go to Configuration → Network → Basic Settings → Report Strategy . You can set the center group and the system will transfer logs via ISUP protocol.
DS-K1T342 Series Face Recognition Terminal User Manual Set ISUP Parameters Set the ISUP parameters for accessing device via ISUP protocol. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Advanced Settings → Platform . 2. Select ISUP from the platform access mode drop-down list. 3. Check Enable. 4. Set the ISUP version, and view the alarm receiver type, server address, port, device ID, register status. Note If you select 5.
DS-K1T342 Series Face Recognition Terminal User Manual Set Video Parameters Click Configuration → Video/Audio → Video . Figure 9-7 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, and the video encoding. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Set the audio stream type and audio encoding. Drag the slider to adjust the device input and output volume.
DS-K1T342 Series Face Recognition Terminal User Manual 9.5.14 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1. Click Configuration → Video/Audio → Prompt . Figure 9-8 Customize Audio Content 2. Select Prompt as TTS(Text to Speech) to turn the text to audio content. 3. Or you can select Prompt as Custom Prompt Importing. 1) Select Custom Type or you can import your custom prompt from local PC.
DS-K1T342 Series Face Recognition Terminal User Manual Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. Set the time duration when authentication failed. 8. 1) Click Add. 2) Set the time duration and the language.
DS-K1T342 Series Face Recognition Terminal User Manual When there are both very bright and very dark areas simultaneously in the view, WDR balances the brightness level of the whole image and provide clear images with details. Brightness/Contrast/Saturation Drag the block or enter the value to adjust the live video's brightness, contrast and saturation. Start/end recording video. Capture the image. 3. Click Default to restore the parameters to the default settings. 9.5.
DS-K1T342 Series Face Recognition Terminal User Manual 9.5.17 Time and Attendance Settings If you want to track and monitor when the persons start/stop work and monitor their working hours and late arrivals, early departures, time taken on breaks, and absenteeism, you can add the person to the shift group and assign a shift schedule (a rule for the attendance defining how the schedule repeats, the shift type, break settings, and the card swiping rule.
DS-K1T342 Series Face Recognition Terminal User Manual Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Manual. 3. Enable the Attendance Status Required and set the attendace status lasts duration. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. Result You should select an attendance status manually after authentication.
DS-K1T342 Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Manual and Auto. 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-10 Set Authentication Parameters Click Save to save the settings after the configuration. Device Type Select Main Card Reader or Sub Card Reader from the drop-down list. Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters. If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description.
DS-K1T342 Series Face Recognition Terminal User Manual Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Recognition Interval You can set the interval between 2 continuous recognition of a same person during the authentication. In the configured interval, Person A can only recognized once. If another person (Person B) has recognized during the interval, Person A can recognized again.
DS-K1T342 Series Face Recognition Terminal User Manual Max. Authentication Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Communication with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max.
DS-K1T342 Series Face Recognition Terminal User Manual ID De-identification You can check ID De-identification, and the ID will not be displayed. Picture Uploading and Storage Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically. Save Captured Picture When Authenticating If you enable this function, you can save the picture when authenticating to the device.
DS-K1T342 Series Face Recognition Terminal User Manual Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticateing by presenting M1 card is available. M1 Card Encryption Sector M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector. By default, Sector 13 is encrypted.
DS-K1T342 Series Face Recognition Terminal User Manual Configure Authentication Result Text Steps 1. Go to Configuration → General → Authentication Result Text . Figure 9-11 Authentication Result Text 2. Enable Customize Authentication Result Text. 3. Enter custom texts. 4. Click Save. 9.5.19 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage.
DS-K1T342 Series Face Recognition Terminal User Manual Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Phase No. Set the device phase No. Building No. Set the device building No. Unit No. Set the device unit No. Note If you change the No., you should reboot the device. If set the device type as Outer Door Station, you can set the period No., outer door station No., and community No. Outer Door Station No.
DS-K1T342 Series Face Recognition Terminal User Manual Press Button to Call Steps 1. Click Configuration → Intercom → Press Button to Call . 2. Set the parameters. - Edit call No. for every button. - Check Call Management Center to set the button calling center. Note If you check Call Management Center and set the call No. as well, call management center has higher privilege than call No. 9.5.20 Access Control Settings Set Door Parameters Click Configuration → Access Control → Door Parameters .
DS-K1T342 Series Face Recognition Terminal User Manual Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed.
DS-K1T342 Series Face Recognition Terminal User Manual Click Save to save the settings after the configuration. No. Set the RS-485 No. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, Access Controller, or Disable. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-13 Wiegand 2. Check Wiegand to enable the Wiegand function. 3. Set a transmission direction. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. Click Save to save the settings. 4. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 9.5.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-14 Set Face Parameters 148
DS-K1T342 Series Face Recognition Terminal User Manual Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T342 Series Face Recognition Terminal User Manual 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. 1:N Matching Threshold Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face Recognition Timeout Value Set the timeout value when face recognizing.
DS-K1T342 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 9-15 Theme Page Display Mode You can select display theme for device authentication. You can select Display Mode as Simple or Normal. When you select Simple, the information of name, ID, face picture will be not displayed. Sleep Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time. Theme Management You can click + Add Program in the frame and upload the screen saver pictures from the local PC.
DS-K1T342 Series Face Recognition Terminal User Manual After you have created a theme, you can select the theme and draw a schedule on the time line to set the theme play schedule. Select the drawn schedule and you can edit the exact start and end time. Select the drawn schedule and you can click Delete or Delete All to delete the schedule. Slide Show Interval Drag the block or enter the number to set the slide show interval. The picture will be changed according to the interval.
DS-K1T342 Series Face Recognition Terminal User Manual Chapter 10 Client Software Configuration 10.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 10-1 Flow Diagram of Configuration on Client Software 10.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T342 Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 10.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T342 Series Face Recognition Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T342 Series Face Recognition Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T342 Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T342 Series Face Recognition Terminal User Manual 10.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T342 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 10.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 10.4.
DS-K1T342 Series Face Recognition Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T342 Series Face Recognition Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T342 Series Face Recognition Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 10.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T342 Series Face Recognition Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by Local Mode. 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station.
DS-K1T342 Series Face Recognition Terminal User Manual Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E.
DS-K1T342 Series Face Recognition Terminal User Manual 10.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K1T342 Series Face Recognition Terminal User Manual Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2.
DS-K1T342 Series Face Recognition Terminal User Manual 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 10.
DS-K1T342 Series Face Recognition Terminal User Manual Figure 10-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T342 Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 10-3 Data Synchronization 10.
DS-K1T342 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T342 Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K1T342 Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached.
DS-K1T342 Series Face Recognition Terminal User Manual ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T342 Series Face Recognition Terminal User Manual View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T342 Series Face Recognition Terminal User Manual 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T342 Series Face Recognition Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T342 Series Face Recognition Terminal User Manual 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. After setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand communication.
DS-K1T342 Series Face Recognition Terminal User Manual 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 10.8 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device.
DS-K1T342 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T342 Series Face Recognition Terminal User Manual Steps 1. Click Monitoring and select a group from the drop-down list on the upper-right corner. The access records triggered at the doors in the selected group will display in real time. You can view the details of the records, including card No., person name, organization, event time, etc. 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected.
DS-K1T342 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T342 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T342 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T342 Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K1T342 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T342 Series Face Recognition Terminal User Manual Appendix D. Dimension The dimension of the device is as follows: Figure D-1 With Fingerprint Module Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T342 Series Face Recognition Terminal User Manual Figure D-2 Without Fingerprint Module 188
DS-K1T342 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD25849B
