DS-K1T343 Series Face Recognition Terminal User Manual
DS-K1T343 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T343 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T343 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T343 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T343 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T343 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T343 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T343 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T343MX 13.56 MHz Card Presenting Frequency DS-K1T343MWX 13.56 MHz Card Presenting Frequency, Wi-Fi DS-K1T343MFX 13.56 MHz Card Presenting Frequency DS-K1T343MFWX 13.
DS-K1T343 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T343 Series Face Recognition Terminal User Manual 6.6 Set Administrator ................................................................................................................. 24 Chapter 7 Basic Operation ........................................................................................................ 27 7.1 Login .................................................................................................................................... 27 7.1.1 Login by Administrator .........
DS-K1T343 Series Face Recognition Terminal User Manual 7.6 Basic Settings ....................................................................................................................... 46 7.7 Set Biometric Parameters .................................................................................................... 49 7.8 Set Access Control Parameters ............................................................................................ 52 7.9 Time and Attendance Status Settings ............
DS-K1T343 Series Face Recognition Terminal User Manual 9.5.1 Set Local Parameters ................................................................................................... 89 9.5.2 View Device Information ............................................................................................. 90 9.5.3 Set Time ...................................................................................................................... 90 9.5.4 Set DST .................................................
DS-K1T343 Series Face Recognition Terminal User Manual 10.3 Group Management ......................................................................................................... 130 10.3.1 Add Group ............................................................................................................... 130 10.3.2 Import Resources to Group ..................................................................................... 130 10.4 Person Management ..............................................
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 4.3-inch LCD touch screen 2 MP wide-angle dual-lens Face anti-spoofing Face recognition distance: 0.3 m to 1.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 2 Appearance The appearance of the device with fingerprint is as follows: Figure 2-1 Appearance（With Fingerprint) The appearance of the device without fingerprint is as follows: Figure 2-2 Appearance（Without Fingerprint) 2
DS-K1T343 Series Face Recognition Terminal User Manual Table 2-1 Appearance Description No. Name 1 Loudspeaker 2 USB Interface 3 MIC 4 Touch Screen 5 IR Light 6 Camera 7 Camera 8 IR Light 9 Card Presenting Area 10 Fingerprint Module Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. Note For details about installation environment, see Tips for Installation Environment. 3.2 Install with Gang Box Steps 1. Make sure the gang box is installed on the wall. Note You should purchase the gang box separately.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 3-2 Install Mounting Plate 3. Route the cables through the cable hole of the mounting plate, and connect to the corresponding peripherals cables. 4. Buckle into the mounting plate after aligning the device with the mounting plate. Use 1 supplied screw (M3) to secure the device on the mounting plate.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 3-3 Secure Device 3.3 Base Mounting Steps 1. Route the cables through the cable hole of the bracket, and connect the terminals with peripherals cables. Place the bracket close to the back side of the device. Figure 3-4 Place Bracket Close to Device Back Side 2. Press the bracket with both hands, and make sure that the buckle of the bracket fits with the back side of the device. Fasten the bracket in the direction of the arrow.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 3-5 Fasten Bracket 3. Buckle into the bracket to the end to complete the installation.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC and COM terminal with the door lock, connect the SENSOR terminal with the door contact, the BTN/GND terminal with the exit button, and connect the Wiegand terminal with the Wiegand card reader or the access controller.
DS-K1T343 Series Face Recognition Terminal User Manual Group Group D No. Function Color Name Description C2 White W1 Wiegand Wiring 1 C3 Black GND Ground White/Purple NC Lock Wiring (NC) D2 White/Yellow COM Common D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Grey BUTTON Exit Door Wiring D1 Door Lock 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-1 Device Wiring ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly. 4.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-2 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module 4.4.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-3 Wire Device Figure 4-4 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-5 Wiring Device Figure 4-6 Wiring Secure Door Control Unit 4.4.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Note The Uninterpretable Power Supply (UPS) is required. The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T343 Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Note Characters containing admin and nimda are not supported to be set as activation password.
DS-K1T343 Series Face Recognition Terminal User Manual 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address.
DS-K1T343 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically. 6.2 Set Application Mode After activating the device, you should select an application mode for better device application.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-2 Welcome Page 2. Tap OK to save. ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-3 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-4 Access to Hik-Connect 2. Tap Next. 6.5 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage. Select parameters according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-5 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic.
DS-K1T343 Series Face Recognition Terminal User Manual Steps 1. Optional: Tap Skip to skip adding administrator if required. 2. Enter the administrator's name (optional) and tap Next. Figure 6-6 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm.
DS-K1T343 Series Face Recognition Terminal User Manual / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . ● ● Enter the device room No. and tap OK to call. Tap to call the center. Note The device should be added to the center, or the calling operation will be failed. Enter PIN code to authenticate.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page. Figure 7-1 Admin Login 2.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-3 Home Page 7.1.3 Forgot Password If you forget the password during authentication, you can reset the password by imprting the key. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the page. 2. Tap in the pop-up admin authentication page. 3. Tap Forget Password in the upper right corner of the page. 4. Plug USB flash drive into the USB interface.
DS-K1T343 Series Face Recognition Terminal User Manual 7.2 Communication Settings You can set the wired network, the Wi-Fi parameter, the RS-485 parameters, the Wiegand parameters, ISUP and access to Hik-Connect on the communication settings page. 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page.
DS-K1T343 Series Face Recognition Terminal User Manual Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm.
DS-K1T343 Series Face Recognition Terminal User Manual Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 4. Tap the back icon at the upper left corner and you should reboot the device if you change the parameters. 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you change the external device, and after you save the device parameters, the device will reboot automatically. 7.2.5 Set ISUP Parameters Set ISUP parameters and the device can upload data via ISUP protocol. Before You Start Make sure your device has connect to a network. Steps 1. Tap Comm. → ISUP .
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-8 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None.
DS-K1T343 Series Face Recognition Terminal User Manual Enable ISUP function and the data will be uploaded via EHome protocol. Address Type Select an address type according to your actual needs. IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. Password If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only.
DS-K1T343 Series Face Recognition Terminal User Manual 7.3 User Management On the user management interface, you can add, edit, delete and search the user. 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID.
DS-K1T343 Series Face Recognition Terminal User Manual Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5.
DS-K1T343 Series Face Recognition Terminal User Manual 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. Tap 10. 7.3.3 Add Fingerprint Add a fingerprint for the user and the user can authenticate via the added fingerprint.
DS-K1T343 Series Face Recognition Terminal User Manual For details about the instructions of scanning fingerprints, see Tips for Scanning Fingerprint . 7. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. 8. Tap 7.3.
DS-K1T343 Series Face Recognition Terminal User Manual Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8. Configure the card type. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user.
DS-K1T343 Series Face Recognition Terminal User Manual The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. 7. Tap 7.3.
DS-K1T343 Series Face Recognition Terminal User Manual 7.4 Data Management You can delete data, import data, and export data. 7.4.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data, Face Data or Access Control Parameters .
DS-K1T343 Series Face Recognition Terminal User Manual 7.4.3 Export Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Export Data . 3. Tap Face Data, Event Data, User Data, or Access Control Parameters. Note The exported access control parameters are configuration files of the device. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password. ● ● ● Note The supported USB flash drive format is DB.
DS-K1T343 Series Face Recognition Terminal User Manual Enter the pin code to authenticate via PIN code. If authentication completed, a prompt "Authenticated" will pop up. 7.5.2 Authenticate via Multiple Credential Before You Start Set the user authentication type before authentication. For details, see Set Authentication Mode . Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-10 Basic Settings Page Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Note If the combination authentication of face and QR code is supported, and the QR code shortcut key is disabled ( there is no QR code shortcut key icon in the authentication page), you can scan the QR code in the middle of the authentication page to authenticate. You can select call type from Call Room, Call Center, and Call Specified Room No. Call Room When you tap the call button on the authentication page, you should dial a room No. to call.
DS-K1T343 Series Face Recognition Terminal User Manual Building No. Set the device installed building No. Unit No. Set the device installed unit No. 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance. The configurable parameters includes select application mode, face liveness level, face recognition distance, face recognition interval, face 1:N security level, face 1:1 security level, ECO settings and face with mask detection.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-11 Biometric Parameters Page Table 7-1 Face Picture Parameters Parameter Description Select Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K1T343 Series Face Recognition Terminal User Manual Parameter Face Recognition Interval Description The time interval between two continuous face recognitions when authenticating. Note You can input the number from 1 to 10. Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T343 Series Face Recognition Terminal User Manual Parameter Description Set the matching value when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask Detection After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask & face 1:N level and the strategy.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-12 Access Control Parameters The available parameters descriptions are as follows: Table 7-2 Access Control Parameters Descriptions Parameter Description Terminal Auth. Mode (Terminal Select the face recognition terminal's authentication mode. You Authentication Mode) can also customize the authentication mode.
DS-K1T343 Series Face Recognition Terminal User Manual Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face. Reader Auth.
DS-K1T343 Series Face Recognition Terminal User Manual 7.9.1 Disable Attendance Mode via Device Disable the attendance mode and the system will not display the attendance status on the initial page. Tap T&A Status to enter the T&A Status page. Figure 7-13 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T343 Series Face Recognition Terminal User Manual Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 7-15 Auto Attendance Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule.
DS-K1T343 Series Face Recognition Terminal User Manual Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.9.4 Set Manual and Auto Attendance via Device Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication.
DS-K1T343 Series Face Recognition Terminal User Manual 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap OK. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule. Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-17 Maintenance Page System Information You can view the device information including serial No., firmware version, MCU version, MAC address, production data, device QR code, open source code license. Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of administrator, user, face picture, card, and event.
DS-K1T343 Series Face Recognition Terminal User Manual All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect. Reboot The device will reboot after the confirmation. Long tap , and enter admin password to view device version information.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-1 Add User 2) Set the following parameters. Employee ID Enter the employee ID. The Employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers.
DS-K1T343 Series Face Recognition Terminal User Manual Enter your name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No. Enter the floor No./room No. Face Add Face picture. Tap Face, then tapImport, and select the mode to import the face. Fingerprint Add fingerprint. Tap Fingerprint, then tap +, and add fingerprint via the fingerprint module.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-2 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync. Mode Manual By default, the device time should be synchronized manually. You can set the device time manually. NTP Set the NTP server's IP address, port No., and interval. 8.4.
DS-K1T343 Series Face Recognition Terminal User Manual Set Port Parameters You can set the HTTP, RTSP, HTTPS, and Server according to actual needs when accessing the device via network. Tap Configuration → Network → Basic Settings → Port , to enter the settings page. HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-3 Wi-Fi 3. Add Wi-Fi. 1) Tap +.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-4 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type. 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters. 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Tap Save. 8.4.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-5 Authentication Settings 2. Tap Save.
DS-K1T343 Series Face Recognition Terminal User Manual Device Type Main Card Reader You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max. Failed Attempts, Enable Tampering Detection and Enable Card No. Reversing.
DS-K1T343 Series Face Recognition Terminal User Manual Communication with Controller Every (s) When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max. Interval When Entering Password (s) When you entering the password on the card reader, if the interval between pressing two digits is longer than the set value, the digits you pressed before will be cleared automatically.
DS-K1T343 Series Face Recognition Terminal User Manual Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time. Overwriting The earliest 5% events will be deleted when the system detects the stored events has been over 95% of the full space. Authentication Settings Display Authentication Result Check Face Picture, Name, or Employee ID. When authentication is completed, the system will display the selected contents in the result.
DS-K1T343 Series Face Recognition Terminal User Manual Set Card Security Tap Configuration → General Settings → Card Security to enter the settings page. Figure 8-7 Card Security Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticateing by presenting M1 card is available.
DS-K1T343 Series Face Recognition Terminal User Manual Enable EM card and authenticating by presenting EM card is available. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. Enable CPU Card The device can read the data from CPU card when enabling the CPU card function. CPU Card Read Content After enable the CPU card content reading function, the device can read the CPU card content.
DS-K1T343 Series Face Recognition Terminal User Manual Face Parameters Settings Tap Configuration → Smart → Intelligent Parameter . Figure 8-9 Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T343 Series Face Recognition Terminal User Manual Select Indoor or Others according to actual environment. In the outdoor scene, indoor scene near the window, or bad environment, you can choose Others. Note If the device is not activated by other tools, the device uses indoor as the environment mode by default. Face Recognition Mode Normal Mode The device uses a camera to perform face recognition. Deep Mode It is applicable for for more complex environments, and the range of people recognized is wider.
DS-K1T343 Series Face Recognition Terminal User Manual After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, its ECO mode, and the strategy. None If the person do not wear a face mask when authenticating, the device will not prompt a notification. Reminder of Wearing If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open.
DS-K1T343 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100. Set Recognition Area Tap Configuration → Smart → Area Configuration to enter the page. Drag the blue frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. If you set the device type as Outer Door Station, you can set the outer door station No. Figure 8-11 Device ID Settings (Outer Door Station) Outer Door Station No.
DS-K1T343 Series Face Recognition Terminal User Manual Note Only the access control device and other devices or systems (such as door station, indoor station, main station, platform) are in the same IP segment, the two-way audio can be performed. Tap Configuration → Intercom → Linked Network Settings . Figure 8-12 Linked Network Settings Set the video intercom server IP and main station's IP. Tap Save. Press Button to Call Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-13 Door Parameters Settings Page 81
DS-K1T343 Series Face Recognition Terminal User Manual Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration.
DS-K1T343 Series Face Recognition Terminal User Manual Tap Configuration → Access Control → RS-485 . Figure 8-14 RS-485 Page Tap Save to save the settings after the configuration. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, or Access Controller. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. Baud Rate The baud rate when the devices are communicating via the RS-485 protocol. Data Bit The data bit when the devices are communicating via the RS-485 protocol.
DS-K1T343 Series Face Recognition Terminal User Manual The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 9 Operation via Web Browser 9.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-1 Live View Page Function Descriptions: Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view.
DS-K1T343 Series Face Recognition Terminal User Manual Full screen view. 9.3 Person Management Click and add the person's information, including the basic information, card, authentication mode, and the picture. Click OK to save the person. Add Basic Information Click User → Add to enter the Add Person page. Add the person's basic information, including the employee ID, the person's name, the gender, user level, floor No., and room No. Click OK to save the settings.
DS-K1T343 Series Face Recognition Terminal User Manual Click OK to save the settings. 9.4 Search Event Click Search to enter the Search page. Figure 9-2 Search Page Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 9.5 Configuration 9.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path.
DS-K1T343 Series Face Recognition Terminal User Manual Set Record File Saving Path Click Configuration → Local to enter the Local page. Select a record file size and select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. Set Captured Pictures Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 9.
DS-K1T343 Series Face Recognition Terminal User Manual Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 9.5.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 9-4 DST Page 2.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K1T343 Series Face Recognition Terminal User Manual Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. Note Do not power off during the upgrading. 9.5.7 Log Query You can search and view the device logs. Go to Configuration → System → Maintenance → Log Query . Set the major and minor type of the log type.
DS-K1T343 Series Face Recognition Terminal User Manual 9.5.9 Certificate Management It helps to manage the server/client certificates and CA certificate. Note The function is only supported by certain device models. Create and Install Self-signed Certificate Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Certificate Files area, select a Certificate Type from the drop-down list. 3. Click Create. 4. Input certificate information. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Steps 1. Go to Configuration → System → Security → Certificate Management . 2. Create an ID in the Inport CA Certificate area. Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 9.5.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK.
DS-K1T343 Series Face Recognition Terminal User Manual Note Some device models do not support Wi-Fi settings. Refer to the actual products when configuration. Set Basic Network Parameters Click Configuration → Network → Basic Settings → TCP/IP . Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port.
DS-K1T343 Series Face Recognition Terminal User Manual Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . Figure 9-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. Optional: Set the WLAN parameters. 4. 1) Click Network Settings.
DS-K1T343 Series Face Recognition Terminal User Manual Select a center group from the drop-down list. Main Channel The device will communicate with the center via the main channel. Note N1 refers to wired network. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Click Configuration → Network → Advanced → Platform Access to enter the settings page. 2. Select the Platform Access Mode. Note Hik-Connect is an application for mobile devices.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you select 5.0 as the version, you should set the ISUP key as well. 5. Set the ISUP listening parameters, including ISUP alarm center IP address/domain name, ISUP alarm center URL, and ISUP alarm center port. 6. Click Save. Configure HTTP Listening The device can send alarm information to the event alarm IP address or domain name via HTTP protocol/HTTPS protocol.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-7 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Set the audio stream type and audio encoding. You can also drag the block to adjust the device input and output volume.
DS-K1T343 Series Face Recognition Terminal User Manual Steps 1. Click Configuration → Video/Audio → Prompt . Figure 9-8 Customize Audio Content 2. Select Prompt as TTS(Text to Speech) to turn the text to audio content. 3. Select time schedule. 4. Enable the function. 5. Set the appellation. 6. Set the time period when authentication succeeded. 1) Click Add. 2) Set the time duration and the language.
DS-K1T343 Series Face Recognition Terminal User Manual Note If authentication is failed in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. Optional: Add holiday schedule. 8. 1) Click Add to add holiday schedule. 2) Repeat step 3 to 6. 9. Click Save to save the settings. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc. NTSC 30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the Philippines, etc. WDR Enable or disable the WDR function. When there are both very bright and very dark areas simultaneously in the view, WDR balances the brightness level of the whole image and provide clear images with details.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-10 Supplement Light Settings Page 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual Result You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. Time Settings Steps 1. Click Configuration → Time Settings to enter the settings page. 2. Select Status Type. 3. Optional: Edit Schedule Name according to the actual needs. 4. Drag mouse to set the schedule. Note Set the schedule from Monday to Sunday according to the actual needs. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Set Auto Attendance via Web Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Auto. 3.
DS-K1T343 Series Face Recognition Terminal User Manual Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 9.5.18 General Settings Set Authentication Parameters Click Configuration → General → Authentication Settings . Note The functions vary according to different models. Refers to the actual device for details.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-11 Set Authentication Parameters Click Save to save the settings after the configuration. Device Type Select Main Card Reader or Sub Card Reader from the drop-down list. Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters. If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description.
DS-K1T343 Series Face Recognition Terminal User Manual Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Recognition Interval You can set the interval between 2 continuous recognition of a same person during the authentication. In the configured interval, Person A can only recognized once. If another person (Person B) has recognized during the interval, Person A can recognized again.
DS-K1T343 Series Face Recognition Terminal User Manual Max. Authentication Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Communication with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max.
DS-K1T343 Series Face Recognition Terminal User Manual You can check Name De-identification, and the whole name will not be displayed. Picture Uploading and Storage Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically. Save Captured Picture When Authenticating If you enable this function, you can save the picture when authenticating to the device.
DS-K1T343 Series Face Recognition Terminal User Manual Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption M1 card encryption can improve the security level of authentication. Sector Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. Enable EM Card Enable EM card and authenticating by presenting EM card is available.
DS-K1T343 Series Face Recognition Terminal User Manual 9.5.19 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage. Click Configuration → Video Intercom → Device No. Figure 9-12 Set Video Intercom Parameters If set the device type as Door Station and Access Control Device, you can set the floor No., door station No., and click Advanced Settings to set the community No.
DS-K1T343 Series Face Recognition Terminal User Manual Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. If set the device type as Outer Door Station, you can set the outer door station No., and click Advanced Settings to set the community No. Outer Door Station No.
DS-K1T343 Series Face Recognition Terminal User Manual Press Button to Call Steps 1. Click Intercom → Press Button to Call to enter the settings page. 2. Set the parameters. - Edit call No. for every button. - Check Call Management Center to set the button calling center. Note If you check Call Management Center and set the call No. as well, call management center has higher privilege than call No. 9.5.20 Access Control Settings Set Door Parameters Click Configuration → Access Control → Door Parameters .
DS-K1T343 Series Face Recognition Terminal User Manual Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed.
DS-K1T343 Series Face Recognition Terminal User Manual Click Save to save the settings after the configuration. No. Set the RS-485 No. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, Access Controller, or Disable. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-14 Wiegand Page 2. Check Wiegand to enable the Wiegand function. 3. Set a transmission direction. Input The device can connect a Wiegand card reader. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-15 Set Face Parameters 119
DS-K1T343 Series Face Recognition Terminal User Manual Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T343 Series Face Recognition Terminal User Manual 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. 1:N Matching Threshold Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face Recognition Timeout Value Set the timeout value when face recognizing.
DS-K1T343 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-16 Theme Page Display Mode You can select display theme for device authentication. You can select Display Mode as Simple or Normal. When you select Simple, the information of name, ID, face picture will be not displayed. Sleep Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time. Theme Management You can click + Add Program in the frame and upload the screen saver pictures from the local PC.
DS-K1T343 Series Face Recognition Terminal User Manual After you have created a theme, you can select the theme and draw a schedule on the time line to set the theme play schedule. Select the drawn schedule and you can edit the exact start and end time. Select the drawn schedule and you can click Delete or Delete All to delete the schedule. Slide Show Interval Drag the block or enter the number to set the slide show interval. The picture will be changed according to the interval.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 10 Client Software Configuration 10.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 10-1 Flow Diagram of Configuration on Client Software 10.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T343 Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 10.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T343 Series Face Recognition Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T343 Series Face Recognition Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T343 Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T343 Series Face Recognition Terminal User Manual 10.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T343 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 10.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 10.4.
DS-K1T343 Series Face Recognition Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 10.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T343 Series Face Recognition Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to . 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station. - Swipe the card on the card reader.
DS-K1T343 Series Face Recognition Terminal User Manual Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. Serial Port It is only available when the model is DS-K1F100-M.
DS-K1T343 Series Face Recognition Terminal User Manual Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5. Add a holiday period to the holiday list and configure the holiday duration. Note Up to 16 holiday periods can be added to one holiday.
DS-K1T343 Series Face Recognition Terminal User Manual 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3.
DS-K1T343 Series Face Recognition Terminal User Manual 10.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Before You Start ● Add person to the client. ● Add access control device to the client and group access points. For details, refer to Group Management .
DS-K1T343 Series Face Recognition Terminal User Manual Figure 10-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 10-3 Data Synchronization 10.
DS-K1T343 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T343 Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K1T343 Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T343 Series Face Recognition Terminal User Manual View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T343 Series Face Recognition Terminal User Manual 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T343 Series Face Recognition Terminal User Manual 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. After setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand communication.
DS-K1T343 Series Face Recognition Terminal User Manual 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 10.8 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device.
DS-K1T343 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T343 Series Face Recognition Terminal User Manual Steps 1. Click Monitoring and select a group from the drop-down list on the upper-right corner. The access records triggered at the doors in the selected group will display in real time. You can view the details of the records, including card No., person name, organization, event time, etc. 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T343 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T343 Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD24342B-A
