User's Manual
Table Of Contents
- Chapter 1 Overview
- Chapter 2 Appearance
- Chapter 3 Installation
- Chapter 4 Terminal Connection
- Chapter 5 Activation
- Chapter 6 Basic Operation
- Chapter 7 Client Operation
- 7.1 User Registration and Login
- 7.2 System Configuration
- 7.3 Access Control Management
- 7.3.1 Adding Access Control Device
- 7.3.2 Viewing Device Status
- 7.3.3 Editing Basic Information
- 7.3.4 Network Settings
- 7.3.5 Capture Settings
- 7.3.6 RS-485 Settings
- 7.3.7 Wiegand Settings
- 7.3.8 Setting Multiple NICs
- 7.3.9 Setting Face Recognition Terminal
- 7.3.10 Remote Configuration
- Checking Device Information
- Editing Device Name
- Editing Time
- Setting System Maintenance
- Configuring RS-485 Parameters
- Managing User
- Setting Security
- Configuring Network Parameters
- Configuring Upload Method
- Configuring Network Center
- Configuring Advanced Network
- Configuring Wi-Fi
- Configuring the Network and SIP Parameters
- Configuring Relay Parameters
- Configuring Access Control Parameters
- Configuring Face Recognition Terminal Parameters
- Configuring Face Picture Parameters
- Configuring Supplement Light Parameters
- Configuring Video and Audio Parameters
- Configuring Volume Input or Output
- Operating Relay
- Viewing Relay Status
- 7.4 Organization Management
- 7.5 Person Management
- 7.5.1 Adding Person
- Adding Person (Basic Information)
- Adding Person (Detailed Information)
- Adding Person (Permission)
- Adding Person (Card)
- Adding Person (Face Picture)
- Adding Person (Fingerprint)
- Adding Person (Attendance Rule)
- Importing Person Information
- Importing Person Pictures
- Exporting Person Information
- Getting Person Information from Access Control Device
- 7.5.2 Managing Person
- 7.5.3 Issuing Card in Batch
- 7.5.1 Adding Person
- 7.6 Schedule and Template
- 7.7 Permission Configuration
- 7.8 Advanced Functions
- 7.9 Searching Access Control Event
- 7.10 Access Control Event Configuration
- 7.11 Door Status Management
- 7.12 Live View
- 7.13 Arming Control
- 7.14 Time and Attendance
- Appendix A Tips for Scanning Fingerprint
- Appendix B Tips When Collecting/Comparing Face Picture
- B.1 Positions (Recommended Distance:0.5 m)
- B.2 Expression
- B.3 Posture
- B.4 Size
- Appendix C Tips for Installation Environment
- Appendix D Relationship Between Wake-up Distance and Environment
- Appendix E Dimension
607 Series Face Recognition Terminal User Manual
62
and the backup channel, or select Close to disable the main channel or the backup channel.
Note: The main channel and the backup channel cannot enable N1 or G1 at the same time.
5. Click Save button to save parameters.
Network Center Settings
You can set the account for EHome protocol in Network Settings page. Then you can add devices
via EHome protocol.
Steps:
1. Click the Network Center tab.
2. Select the center group in the dropdown list.
3. Select the Address Type as IP Address or Domain Name.
4. Input IP address or domain name according to the address type.
5. Input the port No. for the protocol. By default, the port No. is 7660.
6. Select the protocol type as EHome.
7. Set an account name for the network center.
Note: The account should contain 1 to 32 characters and only letters and numbers are allowed.
8. Click Save button to save parameters.
Notes:
The port No. of the wireless network and wired network should be consistent with the port No.
of EHome.
You can set the domain name in Enable NTP area Editing Time section in Remote Configuration.
For details, refer to Time in 7.3.10 Remote Configuration.
Wireless Communication Center Settings
Steps:
1. Click the Wireless Communication Center tab.