DS-K1T642 Series Face Recognition Terminal User Manual
DS-K1T642 Series Face Recognition Terminal User Manual Legal Information ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T642 Series Face Recognition Terminal User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T642 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T642 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T642 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T642 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T642 Series Face Recognition Terminal User Manual • The device cover for indoor use shall be kept from rain and moisture. • Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
DS-K1T642 Series Face Recognition Terminal User Manual Use only power supplies listed in the user instructions: Model Manufacturer Standard ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PDE ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd PB ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd PCU ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd PI ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.
DS-K1T642 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T642 Series Face Recognition Terminal User Manual 6.4.2 Set Wi-Fi Parameters ................................................................................................... 20 6.4.3 Set RS-485 Parameters ................................................................................................ 21 6.4.4 Set Wiegand Parameters ............................................................................................. 22 6.5 User Management .....................................................
DS-K1T642 Series Face Recognition Terminal User Manual 6.13.2 Call Master Station from Device ............................................................................... 40 6.13.3 Call Device from Client Software ............................................................................... 41 6.13.4 Call Indoor Station from Device ................................................................................ 41 Chapter 7 Operation via Web Browser .....................................................
DS-K1T642 Series Face Recognition Terminal User Manual 8.3.1 Add Group ................................................................................................................... 63 8.3.2 Import Resources to Group ......................................................................................... 64 8.3.3 Edit Resource Parameters ........................................................................................... 64 8.3.4 Remove Resources from Group .....................................
DS-K1T642 Series Face Recognition Terminal User Manual 8.5.1 Add Holiday ................................................................................................................. 79 8.5.2 Add Template .............................................................................................................. 80 8.6 Set Access Group to Assign Access Authorization to Persons .............................................. 81 8.7 Configure Advanced Functions ...........................................
DS-K1T642 Series Face Recognition Terminal User Manual 8.11.5 Manually Correct Check-in/out Record ................................................................... 123 8.11.6 Add Leave and Business Trip ................................................................................... 124 8.11.7 Calculate Attendance Data ...................................................................................... 125 8.11.8 Attendance Statistics .................................................................
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features • • • • • • • • • • • • • • • • • • • • 4.3-inch touch screen 2 MP wide-angle dual-lens Face anti-spoofing Face recognition distance: 0.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No. Description 1 White Light 2 Camera 3 Camera 4 White Light 5 Display Screen 6 Fingerprint Module Note Supported by parts of the device modules.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment • Avoid backlight, direct sunlight, and indirect sunlight. • For better recognition, there should be light source in or near the installation environment. Note For details about installation environment, see Tips for Installation Environment. 3.2 Wall Mounting Steps Note The additional force shall be equal to three times the weight of the equipment.
DS-K1T642 Series Face Recognition Terminal User Manual 4. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 5. Align the device with the mounting plate and hang the device on the mounting plate. Figure 3-2 Hang Device 6. Use one supplied screw to secure the device and the mounting plate.
DS-K1T642 Series Face Recognition Terminal User Manual 3.3 Base Mounting Steps 1. Align the hole of the mounting bracket with the device interfaces on the back. Figure 3-4 Align Bracket and Device 2. Push the bracket from bottom to top. Make sure the device is buckled with the bracket. Figure 3-5 Buckle 3. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 4. Put the mounted device on the desk or other surface.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, the exit button, the alarm output/input devices, the Wiegand card reader, the access controller, and the power supply. You can wire the peripherals according to the descriptions below.
DS-K1T642 Series Face Recognition Terminal User Manual Group Group D No. D1 Function Color Door Lock Name Description White/Purple NC Lock Wiring (NC) D2 White/Yellow COM Common D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Gray BUTTON Exit Door Wiring D7 Yellow/Black GND Ground 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T642 Series Face Recognition Terminal User Manual 4.3 Wire Secure Door Control Unit You can connect the terminal with the secure door control unit. The wiring diagram is as follows. Figure 4-2 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module You can connect the terminal with the fire module. 6 wiring type are supported.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 4-3 Device Wiring Wiring Diagram without Secure Door Control Unit: Option 2 Lock Type: Anode Lock, Magnetic Lock, and Electric Bolt (NO) Security Type: Door Open When Powering Off Scenario: Installed in Fire Engine Access; Fire System Controls Access Control Loop Figure 4-4 Device Wiring Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 4-5 Device Wiring Note The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T642 Series Face Recognition Terminal User Manual Lock Type: Anode Lock, Magnetic Lock, and Electric Bolt (NO) Security Type: Door Open When Powering Off Scenario: Installed in Fire Engine Access; Fire System Controls Access Control Loop Figure 4-7 Wiring Diagram Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 5.
DS-K1T642 Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. • After activation, you should select an application mode. For details, see Set Application Mode • After activation, if you need to add the device to the client software or other platforms, you should edit the device IP address. For details, see Communication Settings. 5.
DS-K1T642 Series Face Recognition Terminal User Manual Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4.
DS-K1T642 Series Face Recognition Terminal User Manual 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6. Create a password in the password field, and confirm the password. Caution The password strength of the device can be automatically checked.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 6 Basic Operation 6.1 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-1 Welcome Page 2. Tap OK to save. • • • • Note You can also change the settings in System Settings.
DS-K1T642 Series Face Recognition Terminal User Manual Steps 1. Enter the administrator's name and tap Next. 2. Select a credential to add. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. 3. Click OK. You will enter the authentication page. Scan QR code to authenticate.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-2 Admin Login 2. Authenticate the administrator's face or card to enter the home page. Figure 6-3 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap 4. Optional: Tap and you can enter the device activation password for login. and you can exit the admin login page.
DS-K1T642 Series Face Recognition Terminal User Manual 6.3.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Tap the Password field and enter the device activation password. 3. Tap OK to enter the home page.
DS-K1T642 Series Face Recognition Terminal User Manual Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Network. Figure 6-5 Network Settings 3. Set DHCP, IP Address, Subnet Mask, or Gateway. Note The device's IP address and the computer IP address should be in the same IP segment. 6.4.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-6 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-7 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 4. Tap the back icon at the upper left corner and you should reboot the device if you change the parameters. 6.4.
DS-K1T642 Series Face Recognition Terminal User Manual 6.5 User Management On the user management interface, you can add, edit, delete and search the user. 6.5.1 Add Face Picture Add user's face picture to the device. And the user can use the face picture to authenticate. Steps Note Up to 6,000 face pictures can be added. 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-9 Add Face Picture 6. Look at the camera. Note • Make sure your face picture is in the face picture outline when adding the face picture. • Make sure the captured face picture is in good quality and is accurate. • For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page.
DS-K1T642 Series Face Recognition Terminal User Manual Note The maximum duration for adding a face picture is 15s. You can check the remaining time for adding a face picture on the left of the page. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10.
DS-K1T642 Series Face Recognition Terminal User Manual Note • The same fingerprint cannot be repeatedly added. • Up to 10 fingerprints can be added for one user. • You can also use the client software or the fingerprint recorder to record fingerprints. For details about the instructions of scanning fingerprints, see Tips for Scanning Fingerprint . 7. Set the user role. Administrator The user is the administrator.
DS-K1T642 Series Face Recognition Terminal User Manual 7. Configure the card No. - Enter the card No. manually. - Present the card over the card presenting area to get the card No. Note • The card No. cannot be empty. • Up to 20 characters are allowed in the card No. • The card No. cannot be duplicated. 8. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission.
DS-K1T642 Series Face Recognition Terminal User Manual Note • Only numbers are allowed in the password. • Up to 8 characters are allowed in the password. 6. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 7. Tap to save the settings. 6.5.
DS-K1T642 Series Face Recognition Terminal User Manual Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow to save the settings. the steps in User Management to edit the user parameters. Tap Note The employee ID cannot be edited. 6.6 Data Management You can delete data, import data, and export data. 6.6.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 6.6.
DS-K1T642 Series Face Recognition Terminal User Manual picture. The format should be JPEG or JPG. The resolution should be 640 × 480 pixel or more than of 640 × 480 pixel. The picture size should be between 60 KB and 200 KB. 6.6.3 Export Data Steps 1. On the Home page, tap Data → Export Data . 2. Tap Event Data, User Data, or Face Data 3. Optional: Create a password for exporting. When you should import those data to another device, you should enter the password.
DS-K1T642 Series Face Recognition Terminal User Manual Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. QR Code Put the QR code in front of the device camera to authenticate via QR code. Note Authentication via QR code should be supported by the device. If authentication completed, a prompt "Authenticated" will pop up. 6.7.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-10 Basic Settings Page shortcut key, volume, time, community No., building No., and Unit No Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, and the password entering function. Volume You can enable/disable the audio prompt function and adjust the voice volume. Time Set the time zone, the device time and the DST. Community No.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-11 Biometric Parameters Page Table 6-1 Face Picture Parameters Parameter Face Liveness Level Description You can set the face anti-spoofing matching security level when performing live face authentication. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T642 Series Face Recognition Terminal User Manual Parameter Description Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face 1:1 Security Level Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T642 Series Face Recognition Terminal User Manual Table 6-2 Access Control Parameters Descriptions Parameter Description Terminal Auth. Mode (Terminal Select the face recognition terminal's authentication mode. You Authentication Mode) can also customize the authentication mode. Note • Only the device with the fingerprint module supports the fingerprint related function. • Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 6-13 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 6.11.2 Set Manual Attendance via Device Set the attendance mode as manual, and you can select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode.
DS-K1T642 Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 6-15 Auto Attendance Mode 3. Select an attendance status and set its schedule. 1) Select Check In, Check Out, Break Out, Break In, Overtime In, or Overtime Out as the attendance status. 2) Tap Schedule.
DS-K1T642 Series Face Recognition Terminal User Manual 6.11.4 Set Manual and Auto Attendance via Device Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured parameters. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2.
DS-K1T642 Series Face Recognition Terminal User Manual Result On the initial page and authenticate. If you do not select a status, the authentication will be marked as the configured attendance status according to the schedule. If you tap Select Status and select a status to take attendance, the authentication will be marked as the selected attendance status.
DS-K1T642 Series Face Recognition Terminal User Manual 6.13 Two-Way Audio After adding the device to the client software, you can call the device from the client software, call the master station from the device, call the client software from the device, or call the indoor station from the device. 6.13.1 Call Client Software from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2.
DS-K1T642 Series Face Recognition Terminal User Manual Note For details about the operation, see the user manual of the master station. 6. Answers the call via the master station and starts two-way audio. Note The device will call the master station in priority when tap . 6.13.3 Call Device from Client Software Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2.
DS-K1T642 Series Face Recognition Terminal User Manual 7. Input the room No. on the dial page and tap to call the indoor station. 8. After the indoor station answers the call, you can start two-way audio with the indoor station.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 7 Operation via Web Browser 7.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K1T642 Series Face Recognition Terminal User Manual Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Select the window division type when starting live view. Full screen view. 7.3 Search Event Click Search to enter the Search page. Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search.
DS-K1T642 Series Face Recognition Terminal User Manual NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 7.4.3 Set RS-485 Parameters You can set the RS-485 parameters including the peripheral, address, baud rate and output type.
DS-K1T642 Series Face Recognition Terminal User Manual Input The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. Output The device can connect a Wiegand card reader. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 7.4.5 Set DST Steps 1. Click Configuration → System → System Settings → DST . 2. Check Enable DST. 3.
DS-K1T642 Series Face Recognition Terminal User Manual Import Click and select the file to import. Click Import to start import configuration file. Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. Note Do not power off during the upgrading. 7.4.7 Network Settings Set TCP/IP, port, and Wi-Fi parameters.
DS-K1T642 Series Face Recognition Terminal User Manual Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . 2. Check Enable Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's SSID, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click TCP/IP Settings.
DS-K1T642 Series Face Recognition Terminal User Manual Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3 5) Optional: Click to delete the configured time duration. 5. Click Save to save the settings. 7.4.10 Set Video Intercom Parameters The device can be used as a door station or outer door station. You should set the device No. before usage. Set Device No.
DS-K1T642 Series Face Recognition Terminal User Manual After setting the parameters, you can communicate among the access control device, door station, indoor station, master station, and the platform. Click Save to save the settings after the configuration. 7.4.11 Set Access Control and Authentication Parameters Set the access control parameters and the authentication parameters. Set Door Parameters Click Configuration → Access Control → Door Parameters .
DS-K1T642 Series Face Recognition Terminal User Manual Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect. PAL 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc. NTSC 30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the Philippines, etc. WDR Enable or disable the WDR function.
DS-K1T642 Series Face Recognition Terminal User Manual 7.4.14 Set Face Parameters Enter a short description of your concept here (optional). Set Basic Parameters Click Configuration → Biometric → Basic . Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T642 Series Face Recognition Terminal User Manual ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate Fingerprint Security Level Select the fingerprint security level.
DS-K1T642 Series Face Recognition Terminal User Manual Chapter 8 Client Software Configuration 8.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 8-1 Flow Diagram of Configuration on Client Software 8.2 Device Management You can manage devices on the client, including adding, editing, and deleting the devices. You can also perform operations such as checking device status. 8.2.
DS-K1T642 Series Face Recognition Terminal User Manual remote configuration and management, such as live view, playback, event management, access control, etc. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. Note • You can click Refresh per 60s to refresh the information of the online devices. • SADP log function can be enabled or disabled by right-clicking Online Device.
DS-K1T642 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T642 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T642 Series Face Recognition Terminal User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T642 Series Face Recognition Terminal User Manual Delete Device Select one or multiple devices and click Delete to delete the selected device(s) from the client. Add Devices by IP Segment If the devices share the same port No., user name and password, and their IP addresses are sharing an IP segment. You can specify the start IP address and the end IP address, port No., user name, password, etc of the devices to add them to the client. Steps 1. Enter the Device Management module. 2.
DS-K1T642 Series Face Recognition Terminal User Manual Note • This function should be supported by the device. • You can log into the device to get the certificate file by web browser. 7. Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 8. Optional: Check Import to Group to create a group by the device name. 9. Finish adding the device. - Click Add to add the device and back to the device list page.
DS-K1T642 Series Face Recognition Terminal User Manual 2. Click Add to open the Add window. 3. Select EHome as the adding mode. 4. Enter the required information. Device Account Enter the account name registered on EHome protocol. EHome Key For EHome 5.0 devices, enter the EHome key if you have set it when configuring network center parameter for the device. Note This function should be supported by the device. 5.
DS-K1T642 Series Face Recognition Terminal User Manual 2. 3. 4. 5. Click Add to open the adding device window. Select Batch Import as the adding mode. Click Export Template and then save the pre-defined template (CSV file) on your PC. Open the exported template file and enter the required information of the devices to be added on the corresponding column. Adding Mode You can enter 0 or 1 which indicated different adding modes.
DS-K1T642 Series Face Recognition Terminal User Manual 8.2.2 Reset Device Password If you forgot the password of the detected online devices, you can reset the device password through the client. Steps 1. Enter Device Management page. 2. Click Online Device to show the online device area. All the online devices in the same subnet will display in the list. 3. Select the device from the list and click on the Operation column. 4.
DS-K1T642 Series Face Recognition Terminal User Manual 8.3.2 Import Resources to Group You can import the device resources to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Select a group from the group list and select the resource type such as Access Control Point. 4. Click Import. 5.
DS-K1T642 Series Face Recognition Terminal User Manual 8.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 8.4.1 Add Organization You can add an organization and import person information to the organization for effective management of the persons.
DS-K1T642 Series Face Recognition Terminal User Manual 3. Click Add to open the adding person window. The Person ID will be generated automatically. 4. Enter the basic information including person name, gender, tel, email address, etc. 5. Optional: Set the effective period of the person. Once expired, the credentials and access control settings of the person will be invalid and the person will have no authorization to access the doors\floors.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 8-2 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
DS-K1T642 Series Face Recognition Terminal User Manual This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add.
DS-K1T642 Series Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . Click Add Face in the Basic Information panel. Select Take Photo. Connect the face scanner to the PC running the client.
DS-K1T642 Series Face Recognition Terminal User Manual 3) Click OK to save the captured photo. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons . 8.4.7 Collect Fingerprint via Client Collecting fingerprints locally means you can collect the fingerprint via the fingerprint recorder connected directly to the PC running the client.
DS-K1T642 Series Face Recognition Terminal User Manual 8.4.8 Collect Fingerprint via Access Control Device When adding person, you can collect fingerprint information via the access control device's fingerprint module. The fingerprints recorded can be used as credentials of the persons to access the authorized doors. Before You Start Make sure fingerprint collection is supported by the access control device. Steps 1. Enter Person module. 2.
DS-K1T642 Series Face Recognition Terminal User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Access Control panel, set the person's access control properties. PIN Code The PIN code must be used after card or fingerprint when accessing. It cannot be used independently. It should contain 4 to 8 digits.
DS-K1T642 Series Face Recognition Terminal User Manual 3) Click Add to add the person and close the Add Person window, or click Add and New to add the person and continue to add other persons. 8.4.11 Configure Resident Information If the person is resident, for video intercom purpose, you need to set the room number for her/him and bind an indoor station. After bound, you can call this person by calling the indoor station and perform video intercom with her/him. Steps 1. Enter Person module. 2.
DS-K1T642 Series Face Recognition Terminal User Manual - Click Add and New to add the person and continue to add other persons . 8.4.13 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. 8.4.
DS-K1T642 Series Face Recognition Terminal User Manual Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. to select a face picture file. 5. Click Note • The (folder of) face pictures should be in ZIP format.
DS-K1T642 Series Face Recognition Terminal User Manual 2. Optional: Select an organization in the list. Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. Note • The exported file is in ZIP format. • The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 8.4.
DS-K1T642 Series Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5. Select the organization to move persons to. 6. Click OK. 8.4.20 Issue Cards to Persons in Batch The client provides a convenient way to issue cards to multiple persons in a batch. Steps 1. Enter Person module. 2. Click Batch Issue Cards.
DS-K1T642 Series Face Recognition Terminal User Manual 5. If the lost card is added in one access group and the access group is applied to the device already, after reporting card loss or cancelling card loss, a window will pop up to notify you to apply the changes to the device. After applying to device, these changes can take effect on the device. 8.4.
DS-K1T642 Series Face Recognition Terminal User Manual Remote Mode: Issue Card by Card Reader Select an access control device added in the client and swipe the card on its card reader to read the card number. 8.5 Configure Schedule and Template You can configure the template including holiday and week schedule. After setting the template, you can adopt the configured template to access groups when setting the access groups, so that the access group will take effect in the time durations of the template.
DS-K1T642 Series Face Recognition Terminal User Manual • Move the cursor to the time duration and drag the time duration on the timeline bar to . the desired position when the cursor turns to • Click the time duration and directly edit the start/end time in the appeared dialog. • Move the cursor to the start or the end of time duration and drag to lengthen or shorten .
DS-K1T642 Series Face Recognition Terminal User Manual • Move the cursor to the time duration and drag the time duration on the timeline bar to . the desired position when the cursor turns to • Click the time duration and directly edit the start/end time in the appeared dialog. • Move the cursor to the start or the end of time duration and drag to lengthen or shorten . the time duration when the cursor turns to 4) Repeat the two steps above to draw more time durations on the other days of the week. 6.
DS-K1T642 Series Face Recognition Terminal User Manual 5. In the left list of the Select Person field, select person(s) and the person(s) will be added to the selected list . 6. In the left list of the Select Door field, select door(s) or door station(s) for the selected persons to access, and the selected door(s) or door station(s) will be added to the selected list. 7. Click OK. 8. After adding the access groups, you need to apply them to the access control device to take effect.
DS-K1T642 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T642 Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Enable CPU Card Reserved. If enable the function, the device can recognize the CPU card. You can present CPU card on the device. Enable ID Card Reserved. If enable the function, the device can recognize the ID card. You can present ID card on the device. 4. Click OK. 5.
DS-K1T642 Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event.
DS-K1T642 Series Face Recognition Terminal User Manual Name Edit the card reader name as desired. Minimum Card Swiping Interval If the interval between card swiping of the same card is less than the set value, the card swiping is invalid. You can set it as 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only.
DS-K1T642 Series Face Recognition Terminal User Manual The time interval between two continuous face recognitions when authenticating. By default, it is 2s. Face Anti-spoofing Enable or disable the face anti-spoofing function. If enabling the function, the device can recognize whether the person is a live one or not. Face 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode.
DS-K1T642 Series Face Recognition Terminal User Manual Note Up to 8 time durations can be set to each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K1T642 Series Face Recognition Terminal User Manual 8.7.3 Configure Multi-Factor Authentication You can manage the persons by group and set the authentication for multiple persons of one access control point (door). Before You Start Set access group and apply the access group to the access control device. For details, refer to Set Access Group to Assign Access Authorization to Persons . Perform this task when you want to set authentications for multiple cards of one access control point (door). Steps 1.
DS-K1T642 Series Face Recognition Terminal User Manual Authentication by the access control device and by the client. When the person swipes the card on the device, a window will pop up. You can unlock the door via the client. Figure 8-3 Remotely Open Door Note You can check Offline Authentication to enable the super password authentication when the access control device is disconnected with the client.
DS-K1T642 Series Face Recognition Terminal User Manual 8.7.4 Configure Custom Wiegand Rule Based on the knowledge of uploading rule for the third party Wiegand, you can set multiple customized Wiegand rules to communicate between the device and the third party card readers. Before You Start Wire the third party card readers to the device. Steps Note • By default, the device disables the custom wiegand function.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 8-4 Set Output Transformation Rule 2) Select rules on the left list. The selected rules will be added to the right list. 3) Optional: Drag the rules to change the rule order. 4) Click OK. 5) In the Custom Wiegand tab, set the rule's start bit, length, and the decimal digit. 7. Click Save. 8.7.5 Configure Person Authentication Mode You can set the passing rules for person to the specified the access control device according to your actual needs.
DS-K1T642 Series Face Recognition Terminal User Manual 6. Click OK. Figure 8-5 Set Authentication Modes for Persons 7. Optional: Select person(s) on the Person Authentication mode page, and then click Apply to apply the person authentication mode to the device. Note Person authentication has higher priority than other authentication mode. When the access control device has been configured person authentication mode, the person should authenticate on this device via person authentication mode. 8.7.
DS-K1T642 Series Face Recognition Terminal User Manual 4. 5. 6. 7. 8. 3) Optional: Click or to adjust the display order. 4) Click OK. After selecting the modes, the selected modes will display as icons. Click the icon to select a card reader authentication mode, and drag on the day to draw a color bar on the schedule, which means in that period of time, the card reader authentication is valid. Repeat the above step to set other time periods.
DS-K1T642 Series Face Recognition Terminal User Manual 5. Select person(s) in the left list and the person(s) will be add to the selected persons as the first person(s) of the doors. The added first person(s) will list in the First Person List 6. Optional: Select a first person from the list and click Delete to remove the person from the first person list. 7. Click Save. 8.7.
DS-K1T642 Series Face Recognition Terminal User Manual If you select Reader In_01 as the beginning, and select Reader In_02, Reader Out_04 as the linked card readers. Then you can only get through the access control point by swiping the card in the order as Reader In_01, Reader In_02 and Reader Out_04. 8.7.9 Configure Device Parameters After adding the access control device, you can set its parameters such as network parameters.
DS-K1T642 Series Face Recognition Terminal User Manual Steps Note Make sure the device is not added by EHome. 1. 2. 3. 4. 5. 6. Enter the Access Control module. On the navigation bar on the left, enter Advanced Function → More Parameters . Select an access control device in the device list and enter Network → Uploading Mode . Select the center group from the drop-down list. Check Enable to enable to set the uploading mode. Select the uploading mode from the drop-down list.
DS-K1T642 Series Face Recognition Terminal User Manual Note If set the EHome version as 5.0, you should create an EHome key for the EHome account. 9. Set an account name for the network center. 10. Click Save. Set Device Capture Parameters You can configure the capture parameters of the access control device, including manual capture and event triggered capture. Note • The capture function should be supported by the device.
DS-K1T642 Series Face Recognition Terminal User Manual Set Manual Capture Parameters In Status Monitoring module, you can capture a picture manually the access control device's camera by clicking a button. Before that, you need to set the parameters for the capture such as picture quality. Before You Start Before setting the capture parameters, you should set the saving path first to define where the captured pictures are saved.
DS-K1T642 Series Face Recognition Terminal User Manual If enabled, the captured face picture when authenticating will be saved on the device. ECO Mode After enabling the ECO mode, the device can authenticate faces in the low light or dark environment. And you can set he ECO mode threshold, ECO mode (1:N), and ECO mode (1:1). Note Only device in the normal mode supports configuring ECO mode parameters. Work Mode Set the device work mode as Access Control Mode.
DS-K1T642 Series Face Recognition Terminal User Manual Steps Note This function should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Wiegand to enter the Wiegand Settings page. 4. Set the switch to on to enable the Wiegand function for the device. 5. Select the Wiegand channel No. and the communication mode from the drop-down list.
DS-K1T642 Series Face Recognition Terminal User Manual 8.8 Configure Linkage Actions for Access Control You can configure different linkage actions for the event detected by the access control device. After that, linkage actions will be triggered once the event happens. This mechanism is used for notifying the security personnel the event, or triggering automatic access control in real time.
DS-K1T642 Series Face Recognition Terminal User Manual Send Email Send an email notification of the alarm information to one or more receivers. For details about setting email parameters, refer to Set Email Parameters in the user manual of client software.. 2) Click OK. 5. Enable the event so that when the event is detected, en event will be sent to the client and the linkage actions will be triggered. 6. Optional: Click Copy to...
DS-K1T642 Series Face Recognition Terminal User Manual Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. 8.8.3 Configure Device Actions for Card Swiping You can set the access control device's linkage actions for the specified card swiping. When you swipe the specified card, it can trigger the host buzzer, and other actions on the same device. Steps Note It should be supported by the device. 1. 2. 3. 4. 5. 6. 7.
DS-K1T642 Series Face Recognition Terminal User Manual 8.8.4 Configure Device Actions for Person ID You can set the access control device's linkage actions for the specified person ID. When access control device detects the specified person ID, it can trigger buzzer on card reader, and other actions. Steps Note It should be supported by the device. 1. 2. 3. 4. 5. 6. 7. Click Access Control → Linkage Configuration . Select the access control device from the list on the left. Click Add to add a new linkage.
DS-K1T642 Series Face Recognition Terminal User Manual 8.9 Control Door Status You can control the status for a single door, including opening door, closing door, remaining the door open, and remaining the door closed. Steps 1. Click Monitoring to enter the status monitoring page. 2. Select an access point group on the upper-right corner. Note For managing the access point group, refer to Group Management in the user manual of the client software.
DS-K1T642 Series Face Recognition Terminal User Manual 8.10 Event Center In the Event Center, you can view the real-time events, search the historical events and view the pop-up alarm information. Before the client can receive the event information from the device, you need to arm the device first. For details, refer to Enable Receiving Events from Devices . Before the you can view the pop-up alarm information, you need to enable alarm triggered pop-up image in the event center. For details, refer to . 8.
DS-K1T642 Series Face Recognition Terminal User Manual 8.10.2 View Real-Time Events In the Real-time Event module of the event center page, you can view the real-time event information, including event source, event time, priority, event key words, etc. Before You Start Enable receiving events from devices before the client can receive event information from the device, see Enable Receiving Events from Devices for details. Steps 1.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 8-8 Customize Event Related Items to be Displayed 4. View the event information details. 1) Select an event in the event list. 2) Click Expand in the right-lower corner of the page. 3) View the related picture, detail description and handing records of the event. 4) Optional: Hover the cursor on the related picture, and then click the download icon on the upper-right corner of the picture to download it to the local PC.
DS-K1T642 Series Face Recognition Terminal User Manual Note You should configure the email parameters first, see Set Email Parameters in the user manual of client software for details. 8.10.3 Search Historical Events In the Event Search module of the event center page, you can search the historical events via time, device type, and other conditions according to the specified device type, and then process the events.
DS-K1T642 Series Face Recognition Terminal User Manual All All the device types, and you can set the following filter conditions: group, priority, and status. Video Intercom For the events of video intercom, you need to select searching scope: All Record and Only Unlocking. • All Records: You can filter the events from all the video intercom events, and you need to set the following filter conditions: device, priority, status.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 8-10 Customize Event Related Items to be Displayed 5. Optional: Handle the event(s). - Handle single event: Select one event that need to be processed, and then click Handle in the event information details page, and enter the processing suggestion. - Handle events in a batch: Select the events which need to be processed, and then click Handle in Batch, and enter the processing suggestion.
DS-K1T642 Series Face Recognition Terminal User Manual 8.11 Time and Attendance The Time and Attendance module provides multiple functionalities to track and monitor when employees start and stop work, and full control of employees working hours such as late arrivals, early departures, time taken on breaks and absenteeism. Note In this section, we introduce the configurations before you can getting the attendance reports.
DS-K1T642 Series Face Recognition Terminal User Manual Overtime Level for Workday When you work for certain period after end-work time on workday, you will reach different overtime level: overtime level 1, overtime level 2 and overtime level 3 . You can set different pay rate for three overtime levels, respectively. Pay Rate Set corresponding pay rates for three overtime levels, which can be generally used to calculate total work hours.
DS-K1T642 Series Face Recognition Terminal User Manual Add Regular Holiday You can configure a holiday which will take effect annually on regular days during the effective period, such as New Year's Day, Independence Day, Christmas Day, etc. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Holiday to enter the Holiday Settings page. 3. Check Regular Holiday as holiday type. 4. Custom a name for the holiday. 5. Set the first day of the holiday. 6.
DS-K1T642 Series Face Recognition Terminal User Manual The added holiday will display in the holiday list and calendar. If the date is selected as different holidays, it will be recorded as the first-added holiday. 11. Optional: After adding the holiday, perform one of the following operations. to edit the holiday information. Edit Holiday Click Delete Holiday Select one or more added holidays, and click Delete to delete the holiday(s) from the holiday list.
DS-K1T642 Series Face Recognition Terminal User Manual 5. Set table parameters of database according to the actual configurations. 1) Enter the table name of the third-party database. 2) Set the mapped table fields between the client software and the third-party database. 6. Click Connection Test to test whether database can be connected. 7. Click Save to save the settings. The attendance data will be written to the third-party database.
DS-K1T642 Series Face Recognition Terminal User Manual Configure Report Display You can configure display contents displayed in the attendance report, such as the company name, logo, date format, time format, and mark. Steps 1. Enter Time & Attendance module. 2. Click Attendance Statistics → Report Display . 3. Set the display settings for attendance report. Company Name Enter a company name to display the name in the report.
DS-K1T642 Series Face Recognition Terminal User Manual 6. Set the related attendance time. Start/End-Work Time Set the start-work time and end-work-time. Valid Check-in/out Time Set the time period during which the check-in or check-out is valid. Calculated as Set the duration calculated as the actual work duration. Late/Early Leave Allowable Set the time period for late or early leave. 7. Optional: Select break time to exclude the duration from work hours. Note You can click Settings to manage break time.
DS-K1T642 Series Face Recognition Terminal User Manual Figure 8-11 Add Shift 6. Click Save. The added shift lists on the left panel of the page. At most 64 shifts can be added. 7. Optional: Assign the shift to organization or person for a quick shift schedule. 1) Click Assign. 2) Select Organization or Person tab and check the desired organization(s) or person(s) box. The selected organizations or persons will list on the right page. 3) Set the effective period for the shift schedule.
DS-K1T642 Series Face Recognition Terminal User Manual Set Department Schedule You can set the shift schedule for one department, and all the persons in the department will be assigned with the shift schedule. Before You Start In Time & Attendance module, the department list is the same with the organization. You should add organization and persons in Person module first. See Person Management for details. Steps 1. Click Time & Attendance → Shift Schedule to enter the Shift Schedule Management page. 2.
DS-K1T642 Series Face Recognition Terminal User Manual Steps Note The person schedule has the higher priority than department schedule. 1. 2. 3. 4. 5. Click Time & Attendance → Shift Schedule to enter the Shift Schedule Management page. Click Person Schedule to enter Person Schedule page. Select the organization and select the person(s). Select the shift from the drop-down list. Check the checkbox to enable Multiple Shift Schedules.
DS-K1T642 Series Face Recognition Terminal User Manual 5. Select Workday or Non-Workday from drop-down list. If Non-Workday is selected, you need to set the following parameters. Calculated as Select normal or overtime level to mark the attendance status for temporary schedule. Timetable Select a timetable from drop-down list. Multiple Shift Schedule It contains more than one timetables. The person can check in/out in any of the timetables and the attendance will be effective.
DS-K1T642 Series Face Recognition Terminal User Manual Before You Start • You should add organizations and persons in Person module. For details, refer to Person Management . • The person's attendance status is incorrect. Steps 1. Click Time & Attendance → Attendance Handling to enter attendance handling page. 2. Click Correct Check-In/Out to enter adding the check-in/out correction page. 3. Select person from left list for correction. 4. Select the correction date. 5.
DS-K1T642 Series Face Recognition Terminal User Manual Before You Start You should add organizations and persons in the Person module. For details, refer to Person Management . Steps 1. Click Time & Attendance → Attendance Handling to enter attendance handling page. 2. Click Apply for Leave/Business Trip to enter adding the leave/business trip page. 3. Select person from left list. 4. Set the date(s) for your leave or business trip. 5.
DS-K1T642 Series Face Recognition Terminal User Manual Automatically Calculate Attendance Data You can set a schedule so that the client can calculate the attendance data automatically at the time you configured every day. Steps Note It will calculate the attendance data till the previous day. 1. Enter the Time & Attendance module. 2. Click Attendance Settings → General Rule . 3. In the Auto-Calculate Attendance area, set the time that you want the client to calculate the data every day. 4. Click Save.
DS-K1T642 Series Face Recognition Terminal User Manual 8.11.8 Attendance Statistics You can check the original attendance record, generate and export the attendance report based on the calculated attendance data. Get Original Attendance Record You can search the employee's attendance time, attendance status, check point, etc. in a time period to get an original record of the employees. Before You Start • You should add organizations and persons in Person module and the persons has swiped card.
DS-K1T642 Series Face Recognition Terminal User Manual Before You Start Calculate the attendance data. Note You can calculate the attendance data manually, or set the schedule so that the client can calculate the data automatically every day. For details, refer to Calculate Attendance Data . Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Report . 3. Select a report type. 4. Select the department or person to view the attendance report. 5.
DS-K1T642 Series Face Recognition Terminal User Manual 2) Set the effective period during which the client will send the report on the selected sending date(s). 3) Select the date(s) on which the client will send the report. 4) Set the time at which the client will send the report. Example If you set the effective period as 2018/3/10 to 2018/4/10, select Friday as the sending date, and set the sending time as 20:00:00, the client will send the report at 8 p.m. on Fridays during 2018/3/10 to 2018/4/10.
DS-K1T642 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T642 Series Face Recognition Terminal User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
DS-K1T642 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc.
DS-K1T642 Series Face Recognition Terminal User Manual 133
DS-K1T642 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K1T642 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T642 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
DS-K1T642 Series Face Recognition Terminal User Manual Figure E-2 Device Command 137
UD00000B