User's Manual

ManualsBrandsHIKVISION ManualsElectronicsFace Recognition Terminal

DS-K1T671(B) Series Face Recognition Terminal

Quick Start Guide

About this Manual

The Manual includes instrucons for using and managing the Product. Pictures, charts, images and all

other informaon hereinaer are for descripon and explanaon only. The informaon contained in the

Manual is subject to change, without noce, due to ﬁrmware updates or other reasons. Please ﬁnd the

latest version of this Manual at the Hikvision website (hps://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporng the

Product.

Trademarks

and other Hikvision's trademarks and logos are the properes of Hikvision in various

jurisdicons.

Other trademarks and logos menoned are the properes of their respecve owners. Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED,

WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND

ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE

PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS

OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF

DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE),

PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND

HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR

OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER

INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF

REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY

RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE

RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF

THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY

RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY

PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS

DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY

ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN

SUPPORT OF HUMAN RIGHTS ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER

PREVAILS.

Data Protecon

During the use of device, personal data will be collected, stored and processed. To protect data, the

development of Hikvision devices incorporates privacy by design principles. For example, for device with

facial recognion features, biometrics data is stored in your device with encrypon method; for ﬁngerprint

device, only ﬁngerprint template will be saved, which is impossible to reconstruct a ﬁngerprint image.

As data controller, you are advised to collect, store, process and transfer data in accordance with the

applicable data protecon laws and regulaons, including without limitaon, conducng security controls

to safeguard personal data, such as, implemenng reasonable administrave and physical security

controls, conduct periodic reviews and assessments of the eﬀecveness of your security controls.

Scan the QR code to get the user manual for detailed informaon.

UD27101B

2 Wiring (Normal)

When connecng door contact and exit buon,

the device and the RS-485 card reader should

use the same common ground connecon.

The Wiegand terminal here is a Wiegand input

terminal. You should set the device’s Wiegand

direcon to “input”. If you should connect to

an access controller, you should set the

Wiegand direcon to “Output”. For details, see

the user manual.

The suggested external power supply for door

lock is 12 V, 1 A.

The suggested external power supply for

Wiegand card reader is 12 V, 1 A.

For wiring the ﬁre system, see the user manul.

Do not wire the device to the electric supply

directly.

BTN

(NC)

(COM)

(NO)

Door Contact

116.5 mm

290 mm

33 mm

Hole1 Hole1

Hole2

Hole2Hole2

Hole2

Hole3

Recommended Height:1.40 m.

1 Installation

IR Light IR Light USB Interface

White Light

Camera

Screen

Card Presenng Area

Fingerprint Scanner

The ﬁgures are for reference only.

Debugging Port

(For debugging only)

Power Interface

Wiring Terminal

TF Card Slot

(Reserved)

SIM Card Slot

(Reserved)

Dimension:

Backlight Direct

Sunlight

Direct Sunlight

through Window

Indirect Sunlight

through Window

Close to Light

Installaon Environment:

Indoor and outdoor installaon are supported.

If installing the device outdoors, you should apply Silicone sealant

among the cable wiring area to keep the raindrop from entering.

Before you start:

According to the baseline on the mounng template, sck the mounng template on the wall or other surface, 1.4 meters

higher than the ground.

Make sure the output of external power supply fulﬁls LPS.

Steps:

Drill holes on the wall or other surface according to the mounng template and install the gang box.

Use two supplied screws(4_KA4x22-SUS) to secure the mounng plate on the gang box.

Use another four supplied screws to secure the mounng plate on the wall.

Route the cables through the cable hole of the mounng plate, and connect to the corresponding external device’s cables.

Apply Silicone sealant among the cable wiring area to keep the raindrop from entering.

Insert the ﬁngerprint module to the holes at the boom of the main part.

Align the device with the mounng plate and hang the terminal on the mounng plate.

Make sure the two sheets on each side of the mount plate have been in the holes at the back of the

device.

Use two supplied screws (SC-M4x12TP10-SUS) to secure the device and the mounng plate.

Aer installaon, for the proper use of the device (outdoor use), sck the protecon ﬁlm (parts of models

supplied) on the screen.

The installaon height here is the recommended height. You can change it according to your actual needs.

You can also install the device on the wall or other places without the gang box. For details, refer to the User

Manual.

For easy installaon, drill holes on mounng surface according to the supplied mounng template.

You should purchase the gang box separately.

Apply

Silicone

sealant

Use only power supplies listed in the user instrucons:

Model Manufacturer Standard

C2000IC12.0-24P-DE

C2000IC12.0-24P-GB

ADS-24S-12 1224GPG

MOSO Power Supply Technology Co., Ltd

Shenzhen Honor Electronic Co., Ltd

CEE

Network Interface

GND

87 mm

196.8 mm

Mounng Template

Datum

Summary of content (2 pages)

PAGE 1
Before you start: According to the baseline on the moun ng template, s ck the moun ng template on the wall or other surface, 1.4 meters higher than the ground. 1 Installation Installa on Environment: Dimension: Make sure the output of external power supply fulﬁls LPS. Indoor and outdoor installa on are supported. If installing the device outdoors, you should apply Silicone sealant among the cable wiring area to keep the raindrop from entering.
PAGE 2
.2 Device Wiring (With Secure Door Control Unit Face Recogni on Terminal 485+ 485GND C1 C2 C3 Yellow Blue Black Secure Door Control Unit Wiring Terminal Sensor Input Exit Bu on Lock Output Fire +12 V GND SENSOR GND BUTTON GND NC COM NO A1 A2 Red +12 V Black GND Regulatory Information Ac va on Secure Door Control Unit Power Input RS-485 3 Quick Operation Power on and wire the network cable a er installa on. You should ac vate the device before the ﬁrst login.