DS-K6300 Series Payment Terminal User Manual
DS-K6300 Series Payment Terminal User Manual Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K6300 Series Payment Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K6300 Series Payment Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K6300 Series Payment Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K6300 Series Payment Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K6300 Series Payment Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K6300 Series Payment Terminal User Manual ● ● ● 7. Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). 8. Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion. 9. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. 10.
DS-K6300 Series Payment Terminal User Manual ● ● ● ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Indoor and outdoor use.
DS-K6300 Series Payment Terminal User Manual Available Models Product Name Payment Terminal Model DS-K6300X-MFG 13.56 MHz Card Presenting Frequency, Wi-Fi, 2.4G DS-K6300X-T-MFG 13.56 MHz Card Presenting Frequency, Wi-Fi, 2.4G DS-K6300X-Z-MFG 13.56 MHz Card Presenting Frequency, Wi-Fi, 2.
DS-K6300 Series Payment Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features ................................................................................................................................. 1 1.3 Appearance ...............
DS-K6300 Series Payment Terminal User Manual Chapter 6 Administrator Mode ................................................................................................. 35 6.1 Login by Administrator ......................................................................................................... 35 6.2 Add Administrator ................................................................................................................ 38 6.3 View Consumer Information .................................
DS-K6300 Series Payment Terminal User Manual 9.1 Login .................................................................................................................................... 58 9.2 Live View .............................................................................................................................. 58 9.3 Search Event ........................................................................................................................ 59 9.4 Check Transaction ..............
DS-K6300 Series Payment Terminal User Manual 10.3.1 Add Group ................................................................................................................. 84 10.3.2 Import Resources to Group ....................................................................................... 85 10.3.3 Edit Resource Parameters ......................................................................................... 85 10.3.4 Remove Resources from Group .................................................
DS-K6300 Series Payment Terminal User Manual 10.5 Configure Schedule and Template ................................................................................... 103 10.5.1 Add Holiday ............................................................................................................. 104 10.5.2 Add Template .......................................................................................................... 104 10.6 Set Access Group to Assign Access Authorization to Persons ..............
DS-K6300 Series Payment Terminal User Manual 10.11.4 Set Access Control and Video Intercom Parameters ............................................. 142 10.11.5 Set File Saving Path ............................................................................................... 143 10.11.6 Set Email Parameters ............................................................................................ 143 10.12 Operation and Maintenance .........................................................................
DS-K6300 Series Payment Terminal User Manual Chapter 1 Overview 1.1 Overview Payment terminal is a kind of face recognition terminal for payment, which supports payment via face, card, etc., and is applicable to department stores, canteens, companies, schools, and other situations. 1.2 Features ● ● ● ● ● ● ● ● ● ● Supports payment via card, face, and QR Code. Supports custom payment prompt.
DS-K6300 Series Payment Terminal User Manual No. Description 9 Debugging Port 10 Micro USB Interface Note Use micro USB cable to connect with USB interface. Do not insert or plug USB disk during data transfer. 11 SPK Interface 12 PSAM Card Slot (Reserved) 13 Wiring Terminal 14 Loudspeaker 15 USB Interface 16 QR Code Scanner 17 Audio Plug 1.3.1 Keypad CL: Cancel the payment. RE: Enter an amount, and press RE to refund. CE: Clear one digit each press.
DS-K6300 Series Payment Terminal User Manual Chapter 2 Installation 2.1 Installation Environment ● ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.
DS-K6300 Series Payment Terminal User Manual 2. Remove the notch on the mounting plate to leave the cable hole. Secure the mounting plate on the switching plate with two supplied screws (SC-K1M4×4-BNI-SUS316).
DS-K6300 Series Payment Terminal User Manual 5
DS-K6300 Series Payment Terminal User Manual 3. Align the plate hole with the gang box hole. Secure the mounting plate on the wall with two supplied screws (SC-KA4×22-SUS). 4. Wire the audio cable, and route the cable through the cable hole.
DS-K6300 Series Payment Terminal User Manual 5. Hang the device on the mounting plate from top to bottom in a vertical direction, and secure the device on the mounting plate with 1 supplied screw (SC-KM3X6-H2-SUS). Note Audio cable should be routed from the cable hole to avoid being pressed by the mounting plate.
DS-K6300 Series Payment Terminal User Manual 6. Insert the audio cable into the peripheral module, and insert the module into device from top to bottom in a vertical direction. Secure the peripheral module on the mounting plate with 2 supplied screws (SC-KM3X6-H2-SUS).
DS-K6300 Series Payment Terminal User Manual 2.3 Mount With Cylinder Bracket 2.3.1 Preparation before Mounting with Bracket Make sure you have drilled holes on the turnstile. If not, follow the steps below to drill holes. Steps 1. Use 4 screws (M3 or M4), secured by flange nuts, to install the reinforcing board on the inner surface of the turnstile. Note The distance between the turnstile and the edge should be no longer than 10 mm. 2.
DS-K6300 Series Payment Terminal User Manual Note Solder after pressing rivets to avoid water from entering. Figure 2-1 Drill Holes on Turnstile 3. Solder the other four holes, polish the surface, and implement wire drawing. 4. Solder circular tubes on the turnstile’s inner surface to avoid water from entering.
DS-K6300 Series Payment Terminal User Manual Figure 2-2 Solder Tubes 2.3.2 Cylinder Bracket Mounting Steps 1. Rotate to open the lower cover. 2. Route all cables through the cable hole on the turnstile. Align the holes with those on the turnstile. Secure the rack on the turnstile with 4 supplied screws (SC-OM6×12-H-SUS).
DS-K6300 Series Payment Terminal User Manual 3. Cover the lower cover on the base and rotate to secure. 4. Loosen the screws inside and adjust the device elevaon. Aer adjustment, secure the screws and install the upper cover.
DS-K6300 Series Payment Terminal User Manual Note The elevation can be 0° or 15° (default). 2.4 Base Mounting Steps 1. Set the device flat in a proper place. 2. (Optional) Connect to external keypad. 3. Plug the power cable into the power input interface. After powering on, the device will enter the main interface.
DS-K6300 Series Payment Terminal User Manual Chapter 3 Device Wiring Connect the device to the power supply with the supplied power cable.
DS-K6300 Series Payment Terminal User Manual Chapter 4 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 4.
DS-K6300 Series Payment Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K6300 Series Payment Terminal User Manual 4.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address.
DS-K6300 Series Payment Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 4.
DS-K6300 Series Payment Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K6300 Series Payment Terminal User Manual Chapter 5 Quick Operation 5.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system.
DS-K6300 Series Payment Terminal User Manual Figure 5-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically.
DS-K6300 Series Payment Terminal User Manual 5.2 Set Password Change Type After activating the device, you can set the password change type as reserved email address or security questions. Once you forgot the device password, you can change the password via the selected change type. Change Password via Email Address If you need to change password via reserved email, you can enter an email address, and tap Next.
DS-K6300 Series Payment Terminal User Manual Figure 5-2 Password Change Page Change via Security Questions If you need to change password via security questions, you can tap Change to Security Questions on the right corner. Select the security questions and enter the answers. Click Next.
DS-K6300 Series Payment Terminal User Manual Note You can only select one type to change password. If you need, you can enter the web page to set both of the changing types. 5.3 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K6300 Series Payment Terminal User Manual Figure 5-3 Welcome Page 2. Tap OK to save. ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others.
DS-K6300 Series Payment Terminal User Manual ● ● If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 5.4 Set Network Parameters After activation and select application mode, you can set the network for the device Steps 1. When you enter the Select Network page, tap Wired Network or Wi-Fi for your actual needs.
DS-K6300 Series Payment Terminal User Manual Figure 5-4 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network Note Make sure the device has connected to a network.
DS-K6300 Series Payment Terminal User Manual If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 5.5 Access to Platform Enable the function and the device can communicate via Hik-Connect.
DS-K6300 Series Payment Terminal User Manual Figure 5-5 Access to Hik-Connect 2. Tap Next. 3. Optional: Tap Skip to skip the step. 4. Optional: Tap Previous to go to the previous page.
DS-K6300 Series Payment Terminal User Manual Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected WiFi or connect another Wi-Fi to enter the platform page again. 5.6 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage. Select parameters according to your actual needs.
DS-K6300 Series Payment Terminal User Manual Figure 5-6 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device.
DS-K6300 Series Payment Terminal User Manual Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function. Upload Pic. After Linked Capture (Upload Picture After Linked Capture) Upload the pictures captured by linked camera to the platform automatically. Save Pic. After Linked Capture (Save Pictures After Linked Capture) If you enable this function, you can save the picture captured by linked camera to the device.
DS-K6300 Series Payment Terminal User Manual Figure 5-7 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm.
DS-K6300 Series Payment Terminal User Manual : Enter the card No. or present card on the card presenting area. Click OK. Click OK. 4. You will enter the authentication page. Status Icon Description / Device is armed/not armed. / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected.
DS-K6300 Series Payment Terminal User Manual Chapter 6 Administrator Mode 6.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K6300 Series Payment Terminal User Manual Figure 6-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K6300 Series Payment Terminal User Manual Figure 6-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page.
DS-K6300 Series Payment Terminal User Manual 6.2 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page.
DS-K6300 Series Payment Terminal User Manual 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5.
DS-K6300 Series Payment Terminal User Manual 6.4.1 Set Wired Network Parameters You can set the device wired network parameters, including the IPv4/IPv6 IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wired Network.
DS-K6300 Series Payment Terminal User Manual Figure 6-3 Wired Network Settings 3. Set IPv4/IPv6 IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually. Note The device's IP address and the computer IP address should be in the same IP segment.
DS-K6300 Series Payment Terminal User Manual 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 6.4.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Communication on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap.
DS-K6300 Series Payment Terminal User Manual Figure 6-4 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K6300 Series Payment Terminal User Manual 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 6.4.3 Platform Access You can change the device verification code before you add the device to the Hik-Connect mobile client. Before You Start Make sure your device has connected to a network. Steps 1. Tap Communication on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Hik-Connect. 3. Enable Hik-Connect 4.
DS-K6300 Series Payment Terminal User Manual Figure 6-5 Basic Settings Page Voice Settings You can enable/disable the voice prompt function and adjust the voice volume. Note You can set the voice volume between 0 and 10.
DS-K6300 Series Payment Terminal User Manual Time Settings Set the time zone, the device time and the DST. Sleeping (s) Set the device sleeping waiting time (minute). When you are on the initial page and if you set the sleeping time to 30 min, the device will sleep after 30 min without any operation. Note If you set the sleeping time to 0, the device will not enter sleeping mode. Select Language Select the language according to actual needs.
DS-K6300 Series Payment Terminal User Manual What to do next Enter the tasks the user should do after finishing this task (optional). 6.6.2 Time Settings Enter a short description of your task here (optional). Before You Start Enter the prerequisites here (optional). Enter the context of your task here (optional). Steps 1. Enter your first step here. Enter the result of your step here (optional). Example Enter an example that illustrates the current task (optional).
DS-K6300 Series Payment Terminal User Manual Table 6-1 Face Picture Parameters Parameter Description Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K6300 Series Payment Terminal User Manual Parameter Description Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate Face with Mask Detection After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask & face 1:N level and the strategy.
DS-K6300 Series Payment Terminal User Manual ● ● ● ● ● ● Note If you want to transfer all user information from one device (Device A) to another (Device B), you should export the information from Device A to the USB flash drive and then import from the USB flash drive to Device B. In this case, you should import the user data before importing the profile photo. The supported USB flash drive format is FAT32.
DS-K6300 Series Payment Terminal User Manual Long tap on the initial page for 3 s and slide to the left/right by following the gesture and login the home page. Tap Maint.. Hold the ? on the upper-right corner of the page and enter the password to view the version of the device. Figure 6-7 Maintenance Page System Information You can view the device model, serial No., versions, address, production data, QR code, and open source code license. Note The page may vary according to different device models.
DS-K6300 Series Payment Terminal User Manual Device Upgrade Online Update If the device has been connected to Hik-Connect and network, when there is a new installation package in Hik-Connect, you can tap Device Upgrade → Online Update to upgrade the device system. Update via USB Plug the USB flash drive in the device USB interface. Tap Device Upgrade → Update via USB , and the device will read the digicap.dav file in the USB flash drive to start upgrading.
DS-K6300 Series Payment Terminal User Manual Chapter 7 Operator Mode 7.1 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Tap the Password field and enter the device activation password. 3. Tap OK to enter the home page.
DS-K6300 Series Payment Terminal User Manual Figure 7-1 Home Page 7.2 Payment Administrator (For Operator) Enter a short description of your task here (optional).
DS-K6300 Series Payment Terminal User Manual Before You Start Enter the prerequisites here (optional). Enter the context of your task here (optional). Steps 1. Enter your first step here. Enter the result of your step here (optional). Example Enter an example that illustrates the current task (optional). What to do next Enter the tasks the user should do after finishing this task (optional). 7.3 Payment Settings (For Operator) Enter a short description of your task here (optional).
DS-K6300 Series Payment Terminal User Manual What to do next Enter the tasks the user should do after finishing this task (optional).
DS-K6300 Series Payment Terminal User Manual Chapter 8 Transaction Enter a short description of your concept here (optional). This is the start of your concept.
DS-K6300 Series Payment Terminal User Manual Chapter 9 Operation via Web Browser 9.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:". Enter the device user name and the password.
DS-K6300 Series Payment Terminal User Manual Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view. 9.3 Search Event Click Search to enter the Search page. Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search.
DS-K6300 Series Payment Terminal User Manual 9.5 Configuration 9.5.1 Set Local Parameters Set the live view parameters, record file size and saving path, and captured pictures and clip saving path. Set Live View Parameters Click Configuration → Local to enter the Local page. Configure the stream type, the play performance, auto start live view, and the image format and click Save. Set Record File Size and Saving Path Click Configuration → Local to enter the Local page.
DS-K6300 Series Payment Terminal User Manual Figure 9-1 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the alarm receiver type, NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 9.5.
DS-K6300 Series Payment Terminal User Manual Figure 9-2 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K6300 Series Payment Terminal User Manual Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. If the device has been connected to Hik-Connect and network, when there is a new installation package in Hik-Connect, you can click Upgrade after Online Update to upgrade the device system. Note Do not power off during the upgrading. 9.5.
DS-K6300 Series Payment Terminal User Manual 9.5.8 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK. Caution The password strength of the device can be automatically checked.
DS-K6300 Series Payment Terminal User Manual Set Basic Network Parameters Click Configuration → Network → Basic Settings → TCP/IP . Figure 9-3 TCP/IP Settings Page Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, and the IPv4 default gateway automatically.
DS-K6300 Series Payment Terminal User Manual Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . Figure 9-4 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's name, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4.
DS-K6300 Series Payment Terminal User Manual 2. Select the Platform Access Mode. Note Hik-Connect is an application for mobile devices. With the App, you can view live image of the device, receive alarm notification and so on. 3. Check the checkbox of Enable to enable the function. 4. Optional: Check the checkbox of Custom, and you can set the server address by yourself. 5. Create a Stream Encryption/Encryption Key for the device. Note 6 to 12 letters (a to z, A to Z) or numbers (0 to 9), case sensitive.
DS-K6300 Series Payment Terminal User Manual Set Audio Parameters Click Configuration → Video/Audio → Audio . Select the audio channel. You can also drag the block to adjust the device input and output volume. Click to enable Voice Prompt. Click Save to save the settings after the configuration. Note The functions vary according to different models. Refers to the actual device for details. 9.5.13 Set Payment Prompt Choose to enable payment amount prompt and payment result prompt.
DS-K6300 Series Payment Terminal User Manual When there are both very bright and very dark areas simultaneously in the view, WDR balances the brightness level of the whole image and provide clear images with details. Supplement Light Parameters Set the supplement light type from the drop down list and select to enable or disable it. If you select On, you can set the light brightness. If you select Schedule, you can set the light brightness and its schedule. Start/end recording video. Capture the image. 3.
DS-K6300 Series Payment Terminal User Manual Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Drag the block or enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time.
DS-K6300 Series Payment Terminal User Manual Set Face Recognition Parameters You can set face recognition parameters for accessing. Click Configuration → General → Face Recognition Parameters . You can set Working Mode as Access Control Mode. The access control mode is the device normal mode. You should authenticate your credential for accessing. Click Save to save the settings after the configuration. Set Card Security Click Configuration → General → Card Security to enter the settings page.
DS-K6300 Series Payment Terminal User Manual Figure 9-5 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K6300 Series Payment Terminal User Manual Application Mode Select indoor. Continuous Face Recognition Interval Set the time interval between two continuous face recognitions when authenticating. Rating Set the face rating according to your needs. 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K6300 Series Payment Terminal User Manual 9.5.17 Set Payment Set payment parameters, including meal picking settings, payment verification mode, offline bookkeeping, fixed amount display, insufficient account balance prompt, default payment mode and payment amount limit. Steps 1. Click Configuration → Payment Configuration to enter the Payment Parameters setting page. 2. Click to enable or disable meal picking.
DS-K6300 Series Payment Terminal User Manual Chapter 10 Client Software Configuration 10.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 10-1 Flow Diagram of Configuration on Client Software 10.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K6300 Series Payment Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 10.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K6300 Series Payment Terminal User Manual The port number is obtained automatically. User Name By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K6300 Series Payment Terminal User Manual Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K6300 Series Payment Terminal User Manual Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K6300 Series Payment Terminal User Manual Delete Device Select one or multiple devices and click Delete to delete the selected device(s) from the client. Add Devices by IP Segment If the devices share the same port No., user name and password, and their IP addresses are sharing an IP segment. You can specify the start IP address and the end IP address, port No., user name, password, etc of the devices to add them to the client. Steps 1. Enter the Device Management module. 2.
DS-K6300 Series Payment Terminal User Manual Note ● This function should be supported by the device. ● You can log into the device to get the certificate file by web browser. 7. Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 8. Optional: Check Import to Group to create a group by the device name. 9. Finish adding the device. - Click Add to add the device and back to the device list page.
DS-K6300 Series Payment Terminal User Manual 3. Select EHome as the adding mode. 4. Enter the required information. Device Account Enter the account name registered on EHome protocol. EHome Key For EHome 5.0 devices, enter the EHome key if you have set it when configuring network center parameter for the device. Note This function should be supported by the device. 5. Optional: Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 6.
DS-K6300 Series Payment Terminal User Manual 5. Open the exported template file and enter the required information of the devices to be added on the corresponding column. Adding Mode You can enter 0 or 1 which indicated different adding modes. 0 indicates that the device is added by IP address or domain name; 1 indicates that the device is added via EHome. Address Edit the address of the device.
DS-K6300 Series Payment Terminal User Manual 10.2.2 Reset Device Password If you forgot the password of the detected online devices, you can reset the device password via the client. Steps 1. Enter Device Management page. 2. Click Online Device to show the online device area. All the online devices sharing the same subnet will be displayed in the list. 3. Select the device from the list and click on the Operation column. 4. Reset the device password.
DS-K6300 Series Payment Terminal User Manual - Click Create Group by Device Name and select an added device to create a new group by the name of the selected device. 10.3.2 Import Resources to Group You can import the device resources to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3.
DS-K6300 Series Payment Terminal User Manual All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 10.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc.
DS-K6300 Series Payment Terminal User Manual Steps 1. Enter Person module. Note For the first time you enter Person module, a window pops up, and you can set the rules to generate person ID (letters and numbers supported) when adding person. When getting person information from device, if there are no person IDs, the person IDs will be generated according to the rule. 2. Select an organization in the organization list to add the person. 3. Click Add to open the adding person window.
DS-K6300 Series Payment Terminal User Manual 10.4.3 Issue a Card by Local Mode If a card enrollment station is available, you can issue a card by local mode. To read the card number, you should connect the card enrollment station to the PC running the client by USB interface or COM, and place the card on the card enrollment station. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person panel.
DS-K6300 Series Payment Terminal User Manual Figure 10-3 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
DS-K6300 Series Payment Terminal User Manual Enable or disable the buzzing when the card number is read successfully. Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8.
DS-K6300 Series Payment Terminal User Manual 10.4.5 Take a Photo via Client When adding a person, you can take a photo of the her/him via the client and set this photo as the person's profile. Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first.
DS-K6300 Series Payment Terminal User Manual Figure 10-4 Take a Photo via Client 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 10.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2.
DS-K6300 Series Payment Terminal User Manual Note If you select the enrollment station, you should click Login to set related parameters of the device including IP address, port No., user name, and password. Also, you can check Face AntiSpoofing and select the liveness level as Low, Medium, or High. Face Anti-Spoofing If you check this function, then the device can detect whether the face to be collected is an authentic one. 6. Collect face.
DS-K6300 Series Payment Terminal User Manual 3) Click Add to save the recorded fingerprint. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. Note Once the fingerprint is added, the fingerprint type cannot be changed. 10.4.8 Collect Fingerprint via Access Control Device When adding person, you can collect fingerprint information via the access control device's fingerprint module.
DS-K6300 Series Payment Terminal User Manual 10.4.9 Configure Access Control Information When adding a person, you can set her/his access control information, such as binding an access control group with the person, configuring PIN code, setting the person as a visitor, a blocklist person, or a super user, etc. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. 3. In the Access Control area, click to select access group(s) for the person.
DS-K6300 Series Payment Terminal User Manual Extended Door Open Time Use this function for persons with reduced mobility. When accessing the door, the person will have more time than others to pass through doors. For details about setting the door's open duration, refer to Configure Parameters for Door/ Elevator . Add to Blocklist Add the person to the blocklist and when the person tries to access doors/floors, an event will be triggered and sent to the client to notify the security personnel.
DS-K6300 Series Payment Terminal User Manual 1) Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 2) In the Custom Information panel, enter the person information. 3) Click Add to add the person and close the Add Person window, or click Add and New to add the person and continue to add other persons. 10.4.
DS-K6300 Series Payment Terminal User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Additional Information panel, enter the additional information of the person, including person's ID type, ID No., job title, etc., according to actual needs. 4. Confirm to add the person. - Click Add to add the person and close the Add Person window.
DS-K6300 Series Payment Terminal User Manual 10.4.15 Import Person Pictures After importing face pictures for the added persons to the client, the persons in the pictures can be identified by an added face recognition terminal. You can either import person pictures one by one, or import multiple pictures at a time according to your need. Before You Start Be sure to have imported person information to the client beforehand. Steps 1. Enter the Person module. 2.
DS-K6300 Series Payment Terminal User Manual 10.4.17 Export Person Pictures You can export face picture file of the added persons and save in your PC. Before You Start Make sure you have added persons and their face pictures to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4.
DS-K6300 Series Payment Terminal User Manual Steps ● ● ● Note If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. The gender of the persons will be Male by default. If the card number or person ID (employee ID) stored on the device already exists in the client database, the person with this card number or person ID will not be imported to the client. 1. Enter Person module. 2.
DS-K6300 Series Payment Terminal User Manual 10.4.21 Issue Cards to Persons in Batch The client provides a convenient way to issue cards to multiple persons in a batch. Steps 1. Enter Person module. 2. Click Batch Issue Cards. All the added persons with no card issued will be displayed in the right panel. 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters.
DS-K6300 Series Payment Terminal User Manual PC running the client by USB interface or COM, and place the card on the card enrollment to read the card number. If not, you can also swipe the card on the card reader of the added access control device to get the card number. As a result, before issuing a card to one person, you need to set the card issuing parameters including the issuing mode and related parameters. When adding a card to one person, click Settings to open the Card Issuing Settings window.
DS-K6300 Series Payment Terminal User Manual 10.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K6300 Series Payment Terminal User Manual Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2.
DS-K6300 Series Payment Terminal User Manual 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 10.
DS-K6300 Series Payment Terminal User Manual Figure 10-6 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K6300 Series Payment Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 10-7 Data Synchronization 10.7 Configure Advanced Functions You can configure the advanced functions of access control to meet some special requirements in different scene.
DS-K6300 Series Payment Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K6300 Series Payment Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K6300 Series Payment Terminal User Manual The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event. Super Password The specific person can open the door by inputting the super password. Note ● The duress code and the super code should be different.
DS-K6300 Series Payment Terminal User Manual If the interval between card swiping of the same card is less than the set value, the card swiping is invalid. You can set it as 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Fingerprint Capacity View the maximum number of available fingerprints.
DS-K6300 Series Payment Terminal User Manual Face 1:1 Matching Threshold Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate when authentication. Application Mode You can select indoor or others application modes according to actual environment.
DS-K6300 Series Payment Terminal User Manual Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . ● Click the time duration and directly edit the start/end time in the appeared dialog. ● Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to . 4) Click Save.
DS-K6300 Series Payment Terminal User Manual Before You Start Set access group and apply the access group to the access control device. For details, refer to Set Access Group to Assign Access Authorization to Persons . Perform this task when you want to set authentications for multiple cards of one access control point (door). Steps 1. Click Access Control → Advanced Function → Multi-Factor Auth . 2. Select an access control device in device list on the left panel. 3.
DS-K6300 Series Payment Terminal User Manual Figure 10-8 Remotely Open Door Note You can check Offline Authentication to enable the super password authentication when the access control device is disconnected with the client. Local Authentication and Super Password Authentication by the access control device and by the super password. 4) Select the added person/card group in the left list below and it will be added to the Selected list on the right as the authentication group.
DS-K6300 Series Payment Terminal User Manual 10.7.4 Configure Custom Wiegand Rule Based on the knowledge of uploading rule for the third party Wiegand, you can set multiple customized Wiegand rules to communicate between the device and the third party card readers. Before You Start Wire the third party card readers to the device. Steps ● ● ● Note By default, the device disables the custom wiegand function.
DS-K6300 Series Payment Terminal User Manual Figure 10-9 Set Output Transformation Rule 2) Select rules on the left list. The selected rules will be added to the right list. 3) Optional: Drag the rules to change the rule order. 4) Click OK. 5) In the Custom Wiegand tab, set the rule's start bit, length, and the decimal digit. 7. Click Save. 10.7.5 Configure Person Authentication Mode You can set the passing rules for person to the specified the access control device according to your actual needs.
DS-K6300 Series Payment Terminal User Manual Steps 1. Click Access Control → Advanced Function → Authentication . 2. Select an access control device (support the function of person authentication) on the left panel to enter the person Authentication Mode page. 3. Click Add to enter the Add window. 4. Select the person(s) need to be configured on the left panel. The selected person(s) will be added to the right panel. 5. Select the authentication mode on the drop-down list of Authentication Mode. 6.
DS-K6300 Series Payment Terminal User Manual Figure 10-11 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4.
DS-K6300 Series Payment Terminal User Manual Figure 10-12 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 10.7.7 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K6300 Series Payment Terminal User Manual The door remains open for the configured time duration after the first person is authorized until the remain open duration ends. If you select this mode, you should set the remain open duration. Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication.
DS-K6300 Series Payment Terminal User Manual 4. Click of the selected first card reader in the Card Reader Afterward column to open the select card reader dialog. 5. Select the afterward card readers for the first card reader. Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect.
DS-K6300 Series Payment Terminal User Manual The maximum transmission unit (MTU) of the network interface. Click Save. 6. Set Network Parameters After adding the access control device, you can set the device log uploading mode, and create ISUP account via wired network. Set Log Uploading Mode You can set the mode for the device to upload logs via ISUP protocol. Steps 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3.
DS-K6300 Series Payment Terminal User Manual Note The port number of the wireless network and wired network should be consistent with the port number of ISUP. 8. Select the Protocol Type as ISUP. Note If set the ISUP version as 5.0, you should create an ISUP key for the ISUP account. 9. Set an account name for the network center. 10. Click Save. Set Device Capture Parameters You can configure the capture parameters of the access control device, including manual capture and event triggered capture.
DS-K6300 Series Payment Terminal User Manual 5. Set the capture times once triggered which defines how many pictures will be captures for one time. 6. If the capture times is more than 1, set the interval for each capture. 7. Click Save. Set Manual Capture Parameters In Status Monitoring module, you can capture a picture manually the access control device's camera by clicking a button. Before that, you need to set the parameters for the capture such as picture quality.
DS-K6300 Series Payment Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K6300 Series Payment Terminal User Manual 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. After setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand communication. Steps Note This function should be supported by the device. 1.
DS-K6300 Series Payment Terminal User Manual 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 10.8 Configure Linkage Actions for Access Control You can configure different linkage actions for the event detected by the access control device. After that, linkage actions will be triggered once the event happens.
DS-K6300 Series Payment Terminal User Manual The client software gives an audible warning when the event is triggered. You can select alarm sound for the audible warning. Note For details about setting the alarm sound, refer to Set Alarm Sound in the user manual of the client software. Send Email Send an email notification about the event to one or more receivers. For details about setting email parameters, refer to Set Email Parameters in the user manual of the client software. 2) Click OK. 5.
DS-K6300 Series Payment Terminal User Manual Note The target door and the source door cannot be the same one. 7. Click Save. 8. Optional: After adding the device linkage, you can do one or more of the following: Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. 10.8.
DS-K6300 Series Payment Terminal User Manual Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 10.8.4 Configure Device Actions for Person ID You can set the access control device's linkage actions for the specified person ID. When access control device detects the specified person ID, it can trigger buzzer on card reader, and other actions. Steps Note It should be supported by the device.
DS-K6300 Series Payment Terminal User Manual Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 10.9 Control Door Status You can control the status for the door(s), including unlock door, locking door, remaining the door unlock, remaining the door locked, remain all unlocked, etc.
DS-K6300 Series Payment Terminal User Manual All doors in the group will be unlocked (no matter closed or open). All the persons can access the doors with no credentials required. Remain All Locked All doors in the group will be closed and locked. No person can access the doors even if he/she has the authorized credentials, except the super users. Capture Capture a picture manually. Note The Capture button is available when the device supports capture function.
DS-K6300 Series Payment Terminal User Manual Figure 10-13 Arm Device After turned on, the device(s) will be armed. And notifications about the events triggered by the armed device(s) will be automatically sent to the client software in real-time. 10.10.2 View Real-Time Events The real-time event information received by the client of the connected resources are displayed. You can check the real-time event information, including event source, event time, priority, etc.
DS-K6300 Series Payment Terminal User Manual Filter by Device Type and (or) Priority Select device type(s) and (or) priorities to filter events. Filter by Keywords Enter the keywords to filter the events. Optional: Right-click the table header of the event list to customize the event related items to be 3. displayed in the event list. 4. Select an event in the event list to view the event details. 5. Optional: Perform the following operations if necessary.
DS-K6300 Series Payment Terminal User Manual 10.10.3 Search Historical Events You can search and view historical events by setting search conditions such as time, device type, and priority in the client. For the searched events, you can handle and export them. Before You Start Enable receiving events from devices before the client can receive event information from the device,see Enable Receiving Event from Devices for details. Steps 1. Click Event Center → Event Search to enter the event search page. 2.
DS-K6300 Series Payment Terminal User Manual Enter a key word (supports fuzzy search) to quickly search the target historical event(s). For example, you can enter a person's name to search the events related with this person. 3. Click Search to search the events according the conditions you set. Figure 10-14 Search Historical Events Note If you have selected Access Control as device type in Step 2, you can view extra information such as card No.
DS-K6300 Series Payment Terminal User Manual Figure 10-15 Search Historical Event 4. Optional: Right click the table header of the event list to customize the event related items to be displayed in the event list. 5. Select an event in the event list to view the event details. 6. Optional: Perform one of the following operations.
DS-K6300 Series Payment Terminal User Manual Auto-Play Video Enlarge Video or Picture Send Email Check Auto-Play Video to automatically play video when displaying event details. ● ● Double click the video image to view video in a larger window. Put the cursor on the picture, and click to view picture in a larger window. Select an event and then click Send Email, and the information details of this event will be sent by email.
DS-K6300 Series Payment Terminal User Manual Select Gregorian Calendar or Nepali Calendar as the calendar type. If you select Nepali Calendar, the calender will switch to Nepali language and calculated time by Nepali calendar. You need to restart the client after switching the calendar. Network Performance Set the network conditions to Normal, Better or Best. Save Pictures in Structure Data Format You can enable Save Pictures in Structure Data Format to save structure data and delete registered picture.
DS-K6300 Series Payment Terminal User Manual 10.11.2 Set Picture Storage The pictures, captured by the camera of video access control terminal, triggered by events, can be saved in the PC running the iVMS-4200 Service. You can set the picture storage location here manually. Steps 1. Enter the System Configuration module. 2. Click Event Picture Storage. 3. Set the Store Pictures in Server switch to on. All the disks of the PC running the iVMS-4200 service will show. 4. Select the disk to save the pictures.
DS-K6300 Series Payment Terminal User Manual Steps 1. Open the System Configuration page. 2. Click the Access Control & Video Intercom tab. 3. Input the required information. Ringtone Click and select the audio file from the local path for the ringtone of indoor station. Optionally, you can click for a testing of the audio file. Max. Ring Duration Specify the seconds that the ring will last for at most. The maximum ring duration can be set from 15s to 60s. Max.
DS-K6300 Series Payment Terminal User Manual 2. Click Email tab to enter the Email Settings interface. 3. Enter the required information. STMP Server The STMP server IP address of host name (e.g., smtp.263xmail.com) Encryption Type You can check the radio to select Non-Encrypted, SSL, or STARTTLS . Port Enter the communication port used for SMTP. The port is 25 by default. Sender Address The email address of the sender.
DS-K6300 Series Payment Terminal User Manual Skin Change the skin of the client, including bright-color series and black-color series. Batch Time Sync Synchronize selected devices' time with your PC time. Message Queue After configuring email linkage, the triggered event(s) will be displayed here. Select an event and cancel sending the an email to the receiver.
DS-K6300 Series Payment Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K6300 Series Payment Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K6300 Series Payment Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K6300 Series Payment Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K6300 Series Payment Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K6300 Series Payment Terminal User Manual Appendix D. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure D-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD29338B