Quick Start Guide

Fingerprint Access Control Terminal
Quick Start Guide
UD17820B
1
2
3
Activation
Mounting Screw
Appearance
Installation
1. Install 120 or 86gang box into the wall.
2. Route the cables through the cable hole of
the mounng plate.
3. Secure the device mounng plate on the gang
box with two screws. (Supplied).
4. Connect the corresponding cables.
5. Align the terminal with mounng plate. Push the
terminal in the mounng plate from boom up.
Fasten the terminal with the buckles on the plate.
6. Tighten the screws to fix the terminal on the
mounng plate and complete the installaon.
The default values of the terminal are as follows:
• The default IP address: 192.0.0.64
• The default port No.: 8000
• The default user name: admin
Activating via SADP
1. Download SADP Soware: Get the SADP soware from the supplied disk or the official website. Install and run the soware.
2. Acvate Device: Check the inacve device from the device list. Create a password in the right side of the interface and confirm the password.
3. Edit Device IP Address: Check the device and manually edit the device IP address, Port No., Subnet Mask, Gateway, etc.
Activating via Client Software
STRONG PASSWORD RECOMMENDED
We highly recommend you create a strong password of your own choosing
(using a minimum of 8 characters, including upper case leers, lower case
leers, numbers, and special characters) in order to increase the security of
your product. And we recommend you reset your password regularly,
especially in the high security system, reseng the password monthly or
weekly can beer protect your product.
Activating via Device
Power on and wire the network cable aer installaon.
You should acvate the device before the first login.
Aer powering on, the interface will be displayed as
follows.
You can create the device password and confirm the
password to acvate.
Online Devices (2)
Add to Client
IP
xxxxxxxxxxxxx xxxxxxxxxxxxx XX-XXXXXX8000Activate
Device Type Firmware Version Server PortSecurity Device Serial No.
Add All Modify Netinfo
Reset Password
Activate
Filter
Refresh Every 60s
xx.xx.xx.xx
xxxxxxxxxxxxx xxxxxxxxxxxxx XX-XXXXXX
8000Inactivate
xx.xx.xx.xx
2.4-inch LCD Display
Screen Indicator
Keypad
Fingerprint
Reading Module
Door Bell
Buon
12V
Power Interface
USB Interface/
Reset Buon
(Inside of the Cover)
Ethernet Port
Door Lock
Wiring Terminal
Alarm
Wiring Terminal
RS-485/Wiegand Wiring Terminal
Tamper-proof
Buon
ESC OK
1
2
ABC
3
DEF
4
GHI
6
MNO
7
PQRS
8
TUV
9
WXYZ
0
5
JKL
Exing Key
Direcon Keys
Numeric Keys/
Leer Keys
OK Key
Eding Key
Deleng
Key
EN
OK Key: Press to confirm operaons. Press and hold the
key for 3s to login the main interface.
Deleting Key:
1.Press to delete the leers or numbers one by one;
2.Long-press to clear all contents in the textbox;
Numeric Keys/Letter Keys: Input numbers or leers.
Exiting Key: Press the buon to exit the menu.
Direction Keys: Use , , and to move the cursor.
Editing Key: Press to enter the eding status. Shi among
numbers/lowercases, numbers/uppercases and symbols.
Note: Long press Key 6 for 3s to enter One-Touch Wi-Fi Sengs mode. You can set Wi-Fi parameters
for the device via the App on the phone. Press Key 6 again to exit the mode. (The model with “-1”
does not support One-Touch Wi-Fi Sengs mode.)
Keypad Descriptions
Anticlockwise Rotation
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware
embodied in the Product is governed by the user license agreement
covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright
protecon. Hangzhou Hikvision Digital Technology Co., Ltd.
(“Hikvision”) reserves all rights to this manual. This manual cannot
be reproduced, changed, translated, or distributed, parally or
wholly, by any means, without the prior wrien permission of
Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision
and are registered trademarks or the subject of applicaons for the
same by Hikvision and/or its affiliates. Other trademarks menoned
in this manual are the properes of their respecve owners. No right
of license is given to use such trademarks without express
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTO-
RY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-IN-
FRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS
PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILI-
TY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
1. Get the client soware from the supplied disk or the official website. Install and run the client soware.
2. Click Device Management to enter the Device Management interface.
3. Select an inacve device from the Online Device list. Click Acvate to pop up the Acvaon interface.
4. Create a password and confirm the new password. Click OK to acvate the device.
4. Click “Modify Nenfo” to set the device IP address, mask address, gateway address, and port No.