DS-K3B220X Series Swing Barrier User Manual
DS-K3B220X Series Swing Barrier User Manual Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K3B220X Series Swing Barrier User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K3B220X Series Swing Barrier User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K3B220X Series Swing Barrier User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K3B220X Series Swing Barrier User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K3B220X Series Swing Barrier User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Stainless steel may be corroded in some circumstances. You need to clean and care the device by using the stainless steel cleaner. It is suggested to clean the device every month. Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K3B220X Series Swing Barrier User Manual Available Models Product Name Swing Barrier Model Description DS-K3B220X-L Left Pedestal DS-K3B220X-M Middle Pedestal DS-K3B220X-R Right Pedestal vii
DS-K3B220X Series Swing Barrier User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Main Features ........................................................................................................................ 1 Chapter 2 System Wiring ............
DS-K3B220X Series Swing Barrier User Manual 5.1 Activate via SADP ................................................................................................................. 32 5.2 Activate Device via iVMS-4200 Client Software ................................................................... 33 Chapter 6 Operation via Web Browser ...................................................................................... 35 6.1 Login ........................................................................
DS-K3B220X Series Swing Barrier User Manual 7.2.1 Add Device .................................................................................................................. 62 7.2.2 Reset Device Password ................................................................................................ 64 7.2.3 Manage Added Devices .............................................................................................. 65 7.3 Group Management ...........................................................
DS-K3B220X Series Swing Barrier User Manual Appendix D. Table of Audio Index Related Content ................................................................. 100 Appendix E. Error Code Description ........................................................................................ 101 Appendix F. Communication Matrix and Device Command .....................................................
DS-K3B220X Series Swing Barrier User Manual Chapter 1 Overview 1.1 Introduction The flap barrier with two barriers and 12 IR lights is designed to detect unauthorized entrance or exit. By adopting the flap barrier integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc. 1.
DS-K3B220X Series Swing Barrier User Manual ● ● ● ● ● ● ● Fire alarm passing When the fire alarm is triggered, the barrier will be open automatically for emergency evacuation Valid passing duration settings System will cancel the passing permission if a person does not pass through the lane within the valid passing duration Adjustable indicator brightness Bidirectional (Entering/Exiting) lane The barrier opening and closing speed can be configured according to the visitor flow TCP/IP network communicat
DS-K3B220X Series Swing Barrier User Manual Chapter 2 System Wiring The preparation before installation and general wiring. Steps ● ● ● Note The device should be installed on the concrete surface or other non-flammable surfaces. If the installation area is too close to the wall, make sure the distance between the pedestal and the wall should be no less than 20 mm, or you cannot open the pedestal's top panel. The dimension is as follows.
DS-K3B220X Series Swing Barrier User Manual Figure 2-1 Dimension 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals. Note The distance between the nearest two line is L + 146 mm. L represents the lane width. 3. Slot on the installation surface and dig installation holes. Put 4 expansion bolts of M12*120 for each pedestal.
DS-K3B220X Series Swing Barrier User Manual Figure 2-2 Hole Position and System Wiring 4. Bury cables. Each lane buries 1 high voltage cable and 1 low voltage cable. For details, see the system wiring diagram of step 3. ● ● ● ● ● ● ● Note High voltage: AC power input Low voltage: interconnecting cable (communication cable and 24 V power cable) and network communication cable The supplied 24 V power cable length is 2.5 m and the communication cable length is 3 m.
DS-K3B220X Series Swing Barrier User Manual Chapter 3 Installation 1. Before installation, you should unscrew and disassemble the pedestal. Figure 3-1 Screw Hole 2. Keep the disassembled components and make sure the accessories are intact. 3. Prepare for system wiring and installation. For details, see System Wiring .
DS-K3B220X Series Swing Barrier User Manual 4. Place the pedestal above the embedded expansion bolt. Unscrew and remove the maintenance door. Figure 3-2 Maintenance Door 5. Place the platen on the expansion bolt and adjust the position of the pedestal to make sure the platen fits well to the bottom of the pedestal.
DS-K3B220X Series Swing Barrier User Manual Figure 3-3 Platen 6. Fasten the nuts of the expansion bolts with a screwdriver (shank length more than 120 mm) and reinstall the maintenance door. Scan the QR Code to view the side board installation guide video.
DS-K3B220X Series Swing Barrier User Manual 9
DS-K3B220X Series Swing Barrier User Manual Chapter 4 General Wiring ● ● Note When you should maintain or disassemble the high voltage modules, you should remove the entire high voltage modules and maintain it outside the turnstile. You should unplug the cables that connected to the peripherals before maintenance to avoid destroy of the device. When disassembling the high voltage module, you should disconnect the power to avoid injury. 4.
DS-K3B220X Series Swing Barrier User Manual Figure 4-2 IR Sending/Receiving Module Position Note If the turnstile contains two lanes, standing at the entrance position, the IR modules on the left pedestal are the IR sending modules. The IR modules on the right pedestal are the IR receiving modules. The IR modules on the left side of the middle pedestal are the IR receiving modules, while the IR modules on the right side of the middle pedestal are the IR sending modules. 4.
DS-K3B220X Series Swing Barrier User Manual 4.3 Terminal Description The lane controller contains main lane controller and sub lane controller, which controls the IR beams, motor, and other components' work. 4.3.
DS-K3B220X Series Swing Barrier User Manual Figure 4-3 Main Lane Control Board Terminals 4.3.
DS-K3B220X Series Swing Barrier User Manual Figure 4-4 Sub Lane Control Board Terminals 4.3.3 Access Control Board Terminal Description Access control board is mainly used for authority identification in places with high security levels such as public security or judicial place, external device accessing, and communication with the upper platform and lane controller.
DS-K3B220X Series Swing Barrier User Manual ● ● ● ● Note RS-485A corresponds to serial port 6, connecting to QR code scanner by default. RS-485C corresponds to serial port 8, connecting to card reader by default. The SOC and MCU serial port are for maintenance and debugging use only. Press the Reset button for 5 s and the device will start to restore to factory settings. The DIP switch is for study mode setting and keyfob paring. For detailed information about the DIP switch, see DIP Switch Description.
DS-K3B220X Series Swing Barrier User Manual 4.3.4 Sub Optional Board Terminal Description (Optional) Figure 4-5 Loudspeaker Board Terminal Note The RS-485B corresponds to serial port 7, connecting to QR code scanner by default. The RS-485D corresponds to serial port 5, connecting to card reader by default. The RS-232B corresponds to serial port 3, connecting to fingerprint scanner by default. 4.3.
DS-K3B220X Series Swing Barrier User Manual Figure 4-6 Card Reader Board (RS-485) Figure 4-7 Card Reader Board (USB) 4.3.6 Main Optional Board Terminal Description (Optional) The loudspeaker board contains the sub-1G antenna interface, lane control board interface, loudspeaker interface, debugging port, wiegand/exit button interface, 5 VDC output and communication interface.
DS-K3B220X Series Swing Barrier User Manual Figure 4-8 Loudspeaker Board Terminal 4.3.7 General Wiring The general wiring of lane control board, access control board and optional board.
DS-K3B220X Series Swing Barrier User Manual Figure 4-9 General Wiring ● ● ● ● Note The power cable from power supply to the main lane control board has been connected. You will need to prepare the 14AWG power cable to connect the AC power input to power supply. The supplied 2 interconnecting cables need connecting on-site: 1. 24 V power cable of 14 AWG. The cable is 2.5 m in length and put inside the right/middle pedestal at the exit. 2. UTP-5e Communication cable.
DS-K3B220X Series Swing Barrier User Manual ● ● ● Note If connecting the RS-485 with a card reader, by default, the DIP switch of the card reader is: 1 for entrance, and 4 for exit. If there are other RS-485 devices connecting, the ID of the RS-485 cannot be conflicted. The connected 12 V power interface for the face recognition terminal cannot be connected with other 12 V devices. Figure 4-10 Wiring RS-485 4.3.
DS-K3B220X Series Swing Barrier User Manual 4.3.10 Alarm Input Wiring On the main lane control board, you can wire the fire alarm input interface. Figure 4-12 Remaining Open Figure 4-13 Remaining Closed 4.3.11 Exit Button Wiring The main and sub lane control board each has 1 button interface, which can be connected to exit button or face recognition device.
DS-K3B220X Series Swing Barrier User Manual Figure 4-15 Exit Button Wiring (Exit) ● ● ● Note The face recognition devices are powered via 12 VDC power output interface of the main and sub lane control board. Barrier open at the entrance: connect to BTN1 and GND. Barrier open at the exit: connect to BTN2 and GND. 4.4 Device Settings You can configure the device via button on the main lane control board or the DIP switch on the access control board.
DS-K3B220X Series Swing Barrier User Manual Function Main Lane Control Board & Access Control Board & Loudspeaker (Optional) Card Reading on the Alarm Area Configure via button/web Enter Duration Configure via button/web Exit Duration Configure via button/web IR Sensing Duration Configure via button/web Intrusion Duration Configure via button/web Overstay Duration Configure via button/web Delay Time for Barrier Closing Configure via button/web Authentication on Free Passing Not supp
DS-K3B220X Series Swing Barrier User Manual Button Description Figure 4-16 Button Exit Button Single press to open the barrier from the entrance position. Double press to open the barrier from the exit position.
DS-K3B220X Series Swing Barrier User Manual Button Configuration Procedure Figure 4-17 Procedure Steps: 1. Enter the configuration mode. The number of 1 will show up on the right side of the screen and the device is ready for configuration. 2. Press LEFT and RIGHT to set the configuration No. Press OK to enter the level-2 menu and view the parameters. Press CANCEL, or conduct no operation for 5 s to cancel configuration. 3. Press LEFT and RIGHT to set the parameters at your needs.
DS-K3B220X Series Swing Barrier User Manual 4.4.2 Normal/Study Mode Settings Set normal mode or study mode for device via button or DIP switch. Set Study Mode via Button Enter the study mode through button configuration to set the closed position of the device barrier. Steps 1. Set the configuration No. to "1" and the parameter to "2". The device enters study mode. 2. Power off the device and swing the barrier until it is vertical to the pedestal. 3. Power on the device.
DS-K3B220X Series Swing Barrier User Manual Figure 4-18 DIP Switch Location 27
DS-K3B220X Series Swing Barrier User Manual Figure 4-19 Study Mode 2. Adjust the closed position of the barrier. 3. Power on the device. The device will remember the current position (closed position) automatically. 4. Power off the device. 5. Set the No.1 switches of the 2-digit DIP Switch on the main user extended interface board by referring to the following figure. Figure 4-20 Normal Mode 6. Power on the device again. Note For details about the DIP switch value and meaning, see DIP Switch Description.
DS-K3B220X Series Swing Barrier User Manual 3. Set the configuration No. to "2" and the parameter to "1". The device enters the normal mode. 4. Reboot the device to take effect. Pair Keyfob Pair the remote control to the device through DIP switch to open/close the barrier remotely. Before You Start Ask our technique supports or sales and purchase the keyfob. Steps 1. Power off the turnstile. 2. Set the No.2 switch of the DIP Switch on the access control board to the ON side.
DS-K3B220X Series Swing Barrier User Manual Figure 4-22 Enable Keyfob Paring Mode 3. Power on the turnstile and it will enter the keyfob pairing mode. 4. Hold the Close button for more than 10 seconds. The keyfob's indicator of the will flash twice if the pairing is completed. 5. Set the No.2 switch to the OFF side, and reboot the turnstile to take effect. Note ● Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair.
DS-K3B220X Series Swing Barrier User Manual Note Make sure no persons are in the lane when powering on the device.
DS-K3B220X Series Swing Barrier User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K3B220X Series Swing Barrier User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K3B220X Series Swing Barrier User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B220X Series Swing Barrier User Manual Chapter 6 Operation via Web Browser 6.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K3B220X Series Swing Barrier User Manual Device Component Status You can check if the device is working properly. Click View More to view the detailed component status. Door Status Click to view the device live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Select the streaming type when starting live view. You can select from the main stream and the sub stream.
DS-K3B220X Series Swing Barrier User Manual 6.3 Person Management Click Add to add the person's information, including the basic information, certificate, authentication and settings. Figure 6-2 Add Person Add Basic Information Click Person Management → Add to enter the Add Person page. Add the person's basic information, including the employee ID, the person's name, the gender, and person type. If you select Visitor as the person type, you can set the visit times. Click Save to save the settings.
DS-K3B220X Series Swing Barrier User Manual Authentication Settings Click Person Management → Add to enter the Add Person page. Set the authentication type. Click Save to save the settings. Add Card Click Person Management → Add to enter the Add Person page. Click Add Card, enter the Card No. and select the Property, and click OK to add the card. Note Up to 50 cards can be added. Click Save to save the settings. Authentication Settings Click Person Management → Add to enter the Add Person page.
DS-K3B220X Series Swing Barrier User Manual Figure 6-3 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel.
DS-K3B220X Series Swing Barrier User Manual 6.5 Configuration 6.5.1 View Device Information Click Configuration → System → System Settings → Basic Information to enter the configuration page. You can view the device name, language, model, serial No., version, IO input, IO output, local RS-485, alarm input, alarm output, and device capacity, etc. You can change Device Name and click Save. 6.5.2 Set Time Set the device's time. Click Configuration → System → System Settings → Time Settings .
DS-K3B220X Series Swing Barrier User Manual You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. Server Address Type/Server Address/NTP Port/Interval You can set the server address type, server address, NTP port, and interval. 6.5.3 Set DST Steps 1.
DS-K3B220X Series Swing Barrier User Manual 6.5.6 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → User Management → Arming/Disarming Information . You can view the device arming/disarming information. Click Refresh to refresh the page. 6.5.7 Network Settings Set TCP/IP and port. Set Basic Network Parameters Click Configuration → Network → Network Settings → TCP/IP .
DS-K3B220X Series Swing Barrier User Manual Select a NIC type from the drop-down list. By default, it is Auto. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, Mac address, and MTU. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, the IPv4 default gateway automatically. DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need.
DS-K3B220X Series Swing Barrier User Manual HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. HTTP Listening The device can send alarm information to the event alarm IP address or domain name via HTTP protocol/HTTPS protocol.
DS-K3B220X Series Swing Barrier User Manual - If you choose Linkage Type as Employee ID Linkage, you need to enter the employee ID and select the card reader. 3. Set linked action. Linked Buzzer Enable Linked Buzzer and select Start Buzzing or Stop Buzzing for the target event. Linked Door Enable Linked Door, check Door 1 or Door 2, and set the door status for the target event.
DS-K3B220X Series Swing Barrier User Manual Terminal Choose Entrance or Exit for settings. Terminal Type/Terminal Model Get terminal description. They are read-only. Enable Authentication Device Enable the authentication function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Authentication Interval You can set the authentication interval of the same person when authenticating. The same person can only authenticate once in the configured interval.
DS-K3B220X Series Swing Barrier User Manual Figure 6-9 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select Entrance or Exit for settings. Door Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Note The open duration ranges from 5 s to 60 s. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs.
DS-K3B220X Series Swing Barrier User Manual Figure 6-10 Serial Port Settings 2. Set the No., Baud Rate, Data Bit, Stop Bit and Parity. 3. Set the Peripheral Type as Card Reader, QR Code Scanner or Disable. 4. You can view the serial port type, connected device model and peripheral software version. 5. Click Save. Host Parameters Set door contact settings and RS-485 protocol. Steps 1. Click Configuration → Access Control → Host Parameter to enter the page. 2. Set door contact.
DS-K3B220X Series Swing Barrier User Manual Set Terminal Parameters Set the working mode. Steps 1. Set the device working mode. Figure 6-11 Working Mode Permission Free Mode The device will not verify the person's permission, but only the person's validity period. If the person is in the validity period, the barrier will open. You can enable Verify Credential Locally. After enabling the function, the device will only verify the person's permission without the schedule template, etc.
DS-K3B220X Series Swing Barrier User Manual Figure 6-12 Basic Parameters 2. View the Device Type, Device Model and Working Status. 3. Set Barrier Material, Lane Width, Barrier Opening Speed and Barrier Closing Speed. 4. Set the passing mode. - If you choose General Passing, you can select the barrier status for the entrance and exit from the drop-down list. - If you choose Weekly Schedule, you can set a weekly schedule for entrance and exit barriers. 5. Click Save. keyfob Set keyfob patameters. Steps 1.
DS-K3B220X Series Swing Barrier User Manual Figure 6-13 keyfob 2. View the keyfob working status. 3. Set Working Mode as One-to-One or One-to-Many. 4. Add keyfob. 1) Click Add and the keyfob adding window will pop up. 2) Enter the Name and Serial No.. 3) Check to enable Remain Open Permission at your actual needs. 4) Click OK to add the keyfob. 5. Optional: Select a keyfob and click Delete to delete the keyfob. 6. Click Save. IR Detector Set IR detector. Steps 1.
DS-K3B220X Series Swing Barrier User Manual Enable Custom Anti-pinch for Door Closing Anti-pinch for door closing refers that the barrier will not close if the device has detected person in the lane. Only after the person walks out of the lane, the barrier will close. If you enable the function, you can shield parts of the IR beams for closing barrier in advance. But this action may hit person and cause injury. 4. Click Save. People Counting Set people counting . Steps 1.
DS-K3B220X Series Swing Barrier User Manual Note The alarm output duration ranges from 0 s to 3599 s. 3. Set Temperature Unit. 4. Check to enable Do Not Open Barrier When Lane is Not Clear. 5. Drag the block or enter the value to adjust the light board brightness. 6. Set the alarm buzzer beeping duration, door closing delay time, max. intrusion duration, overstaying duration and max. IR obstructed duration. 7. Check to enable Memory Mode at your actual needs.
DS-K3B220X Series Swing Barrier User Manual Figure 6-16 Card Type Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption Sector M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector.
DS-K3B220X Series Swing Barrier User Manual Enable CPU Card Enable CPU card and authenticating by presenting CPU card is available. CPU Card Read Content After enable the CPU card content reading function, the device can read the CPU card content. Enable ID Card Enable ID card and authenticating by presenting ID card is available. Enable FeliCa Card The device can read the data from FeliCa card when enabling the FeliCa card function.
DS-K3B220X Series Swing Barrier User Manual Note Do not power off during the upgrading. Restore Parameters Click Maintenance and Security → Maintenance → Backup and Reset . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Restore The device will restore to the default settings, except for the device IP address and the user information. Import and Export Parameters Click Maintenance and Security → Maintenance → Backup and Reset .
DS-K3B220X Series Swing Barrier User Manual Main Lane Status Figure 6-17 Main Lane Status Device Component You can view the status of the access control board, lane control board, extended interface board, and arrow light board. Peripheral You can view the status of the RS-485 card reader. Temperature You can view the pedestal temperature. Movement You can view the working status of motor encoder.
DS-K3B220X Series Swing Barrier User Manual Peripheral You can view the status of the RS-485 card reader. Movement You can view the working status of motor encoder. Others Figure 6-19 Other Status Passing Mode You can view the entrance and exit mode. IR Detector Status You can view the status of each pair of the 4 IR beam sensors. Input and Output Status You can view the status of the event input, alarm output and fire alarm.
DS-K3B220X Series Swing Barrier User Manual The results will be displayed below, which including the No., time, the major type the minor type, the channel No., the local/remote user information, the remote host IP, etc. 6.5.17 Certificate Management It helps to manage the server/client certificates and CA certificate. Note The function is only supported by certain device models. Create and Install Self-signed Certificate Steps 1. Go to Maintenance and Security → Security → Certificate Management . 2.
DS-K3B220X Series Swing Barrier User Manual Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1. Go to Maintenance and Security → Security → Certificate Management . 2. Create an ID in the Import CA Certificate area. Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install.
DS-K3B220X Series Swing Barrier User Manual Chapter 7 Client Software Configuration You can call the hotline to get the iVMS-4200 client software installation package. 7.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software.
DS-K3B220X Series Swing Barrier User Manual 7.2 Device Management The client supports managing access control devices and video intercom devices. Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 7.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol.
DS-K3B220X Series Swing Barrier User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B220X Series Swing Barrier User Manual 5. Open the exported template file and enter the required information of the devices to be added on the corresponding column. Note For detailed description of the required fields, refer to the introductions in the template. Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin.
DS-K3B220X Series Swing Barrier User Manual All the online devices sharing the same subnet will be displayed in the list. 3. Select the device from the list and click on the Operation column. 4. Reset the device password. - Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support.
DS-K3B220X Series Swing Barrier User Manual Refresh Device Information Click to refresh and get the latest device information. Upgrade Device View device status in the Firmware Upgrade column, check one or more upgradable devices, and click Upgrade Device Firmware to upgrade the selected devices. For details, refer to . Get Events from Device Check one device, and click Get Events from Device to synchronize events. For details, refer to . 7.
DS-K3B220X Series Swing Barrier User Manual Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Select a group from the group list and select the resource type as Access Point, Alarm Input, Alarm Output, etc. 4. Click Import. 5. Select the thumbnails/names of the resources in the thumbnail/list view.
DS-K3B220X Series Swing Barrier User Manual ● ● Show Persons in Sub Organization Note The lower-level organizations will be deleted as well if you delete an organization. Make sure there is no person added under the organization, or the organization cannot be deleted. Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations. 7.4.
DS-K3B220X Series Swing Barrier User Manual Import Person Pictures After importing face pictures for the added persons to the client, the persons in the pictures can be identified by an added face recognition terminal. You can either import person pictures one by one, or import multiple pictures at a time according to your need. Before You Start Be sure to have imported person information to the client beforehand. Steps 1. Enter the Person module. 2.
DS-K3B220X Series Swing Barrier User Manual The Export panel is displayed. 5. Check Person Information as the content to export. 6. Check desired items to export. 7. Click Export to save the exported file in CSV/Excel file on your PC. Export Person Pictures You can export face picture file of the added persons and save in your PC. Before You Start ● Make sure you have added persons and their face pictures to an organization.
DS-K3B220X Series Swing Barrier User Manual Steps ● ● ● Note If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. The gender of the persons will be Male by default. If the card number or person ID (employee ID) stored on the device already exists in the client database, the person with this card number or person ID will not be imported to the client. 1. Enter Person module. 2.
DS-K3B220X Series Swing Barrier User Manual 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station. - Swipe the card on the card reader. - Manually enter the card number and press the Enter key. The person(s) in the list will be issued with card(s). 7.4.
DS-K3B220X Series Swing Barrier User Manual Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. Serial Port It is only available when the model is DS-K1F100-M. Select the COM the card enrollment station connects to.
DS-K3B220X Series Swing Barrier User Manual Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5. Add a holiday period to the holiday list and configure the holiday duration. Note Up to 16 holiday periods can be added to one holiday.
DS-K3B220X Series Swing Barrier User Manual 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3.
DS-K3B220X Series Swing Barrier User Manual 7.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Before You Start ● Add person to the client. ● Add access control device to the client and group access points. For details, refer to Group Management . ● Add template.
DS-K3B220X Series Swing Barrier User Manual Figure 7-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K3B220X Series Swing Barrier User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 7-3 Data Synchronization 7.
DS-K3B220X Series Swing Barrier User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Before You Start Add access control device to the client. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K3B220X Series Swing Barrier User Manual Press Key to Enter Card Number If you enable this function, you can input the card No. by pressing the key. NFC An i-Cloning If you enable this function, you cannot use the cloned card for authentication and further enhance security. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K3B220X Series Swing Barrier User Manual Door Locked Time After swiping the normal card and relay action, the timer for locking the door starts working. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered.
DS-K3B220X Series Swing Barrier User Manual Steps 1. Click Access Control → Advanced Function → Device Parameter . 2. In the device list on the left, click to expand the door, select a card reader and you can edit the card reader's parameters on the right. 3. Edit the card reader basic parameters in the Basic Information page. ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows.
DS-K3B220X Series Swing Barrier User Manual Select the fingerprint recognition level in the drop-down list. Default Card Reader Authentication Mode View the default card reader authentication mode. Fingerprint Capacity View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance.
DS-K3B220X Series Swing Barrier User Manual user cannot authenticate via the fake face within 5 minutes. Within the 5 minutes, the user can authenticate via the real face twice continuously to unlock. Application Mode You can select indoor or others application modes according to actual environment. 4. Click OK. 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s).
DS-K3B220X Series Swing Barrier User Manual Passing Mode Select the controller which will control the barrier status of the device. ● If you select According to Lane Controller's DIP Settings, the device will follow the lane controller's DIP settings to control the barrier. The settings on the software will be invalid. ● If you select According to Main Controller's Settings, the device will follow the settings of the software to control the barrier. The DIP settings of the lane controller will be invalid.
DS-K3B220X Series Swing Barrier User Manual 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Face Recognition Terminal. 4. Set the parameters. Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface.
DS-K3B220X Series Swing Barrier User Manual 4. Select the serial port number from the drop-down list to set the RS-485 parameters. 5. Set the baud rate, data bit, the stop bit, parity type, communication mode, working mode, and connection mode in the drop-down list. Note When the connection mode is Connect Access Control Device, you can select Card No. or Person ID as the output type. 6. Click Save. ● The configured parameters will be applied to the device automatically.
DS-K3B220X Series Swing Barrier User Manual Steps Note The function should be supported by the access control device and the card reader. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. The sector ID ranges from 1 to 100. 6.
DS-K3B220X Series Swing Barrier User Manual Note For managing the access point group, refer to Group Management . The doors in the selected access control group will display. 3. Click a door icon to select a door, or press Ctrl and select multiple doors. Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once.
DS-K3B220X Series Swing Barrier User Manual 7.8.2 Check Real-Time Access Records The real-time access records can be displayed in the client, including card swiping records, face recognition records, skin-surface temperature information, etc. Also, you can view the person information and view the picture captured during access. Before You Start You have added person(s) and access control device(s) to the client. For details, refer to Person Management and Add Device . Steps 1.
DS-K3B220X Series Swing Barrier User Manual Note In Linked Capture Picture field, you can double click the captured picture to view an enlarged picture. to view surveillance details (including person's detailed information and the 7. Optional: Click captured picture). Note In the pop-up window, you can click to view surveillance details in full screen.
DS-K3B220X Series Swing Barrier User Manual Appendix A. DIP Switch A.1 DIP Switch Description The DIP switch is on the access control board. No.1 and No 2 is from the low bit to the high bit. Figure A-1 DIP Switch When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. A.2 DIP Switch Corresponded Functions Note After setting the DIP switch, you should reboot the device, or the function cannot take effect.
DS-K3B220X Series Swing Barrier User Manual Appendix B. Button Configuration Description Refer to the table below for device configuration via button on the main lane control board. No.
DS-K3B220X Series Swing Barrier User Manual No.
DS-K3B220X Series Swing Barrier User Manual No.
DS-K3B220X Series Swing Barrier User Manual No.
DS-K3B220X Series Swing Barrier User Manual No.
DS-K3B220X Series Swing Barrier User Manual No. Description Default Value Parameters Notes brighter the light will be. 40 Self-check Voice Prompt 2 1-Disable 2-Enable Voice prompt of self-check at startup and motor inspection 41 Study Mode Voice 2 Prompt 1-Disable 2-Enable Voice prompt of study mode 42 IR Detector Quantity 4-4，6-6，8-8, Unable to change 99 Restore to Default 1 1- Default 2- Start The device will reboot.
DS-K3B220X Series Swing Barrier User Manual Appendix C.
DS-K3B220X Series Swing Barrier User Manual Appendix D. Table of Audio Index Related Content Index Content 1 Climbing over the barrier. 2 Reverse passing. 3 Passing timeout. 4 Intrusion. 5 Tailgating. 6 Overstay.
DS-K3B220X Series Swing Barrier User Manual Appendix E. Error Code Description The swing barrier will display the error code on the seven-segment display if error occurred. Refer to the table below to find the description of each number.
DS-K3B220X Series Swing Barrier User Manual Appendix F. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure F-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UDB
