User's Manual
Table Of Contents
- Legal Information
- Regulatory Information
- Safety Instruction
- Available Models
- Chapter 1 Overview
- Chapter 2 System Wiring
- Chapter 3 Installation
- Chapter 4 General Wiring
- 4.1 Components Introduction
- 4.2 Wiring
- 4.3 Terminal Description
- 4.3.1 Main Lane Control Board Terminal Description
- 4.3.2 Sub Lane Control Board Terminal Description
- 4.3.3 Access Control Board Terminal Description
- 4.3.4 Sub Optional Board Terminal Description (Optional)
- 4.3.5 Card Reader Board Terminal Description
- 4.3.6 Main Optional Board Terminal Description (Optional)
- 4.3.7 General Wiring
- 4.3.8 RS-485 Wiring
- 4.3.9 RS-232 Wiring
- 4.3.10 Alarm Input Wiring
- 4.3.11 Exit Button Wiring
- 4.4 Device Settings
- Chapter 5 Activation
- Chapter 6 Operation via Web Browser
- 6.1 Login
- 6.2 Live View
- 6.3 Person Management
- 6.4 Search Event
- 6.5 Configuration
- 6.5.1 View Device Information
- 6.5.2 Set Time
- 6.5.3 Set DST
- 6.5.4 Change Administrator's Password
- 6.5.5 Online Users
- 6.5.6 View Device Arming/Disarming Information
- 6.5.7 Network Settings
- 6.5.8 Event Linkage
- 6.5.9 Access Control Settings
- 6.5.10 Turnstile
- 6.5.11 Card Settings
- 6.5.12 Set Privacy Parameters
- 6.5.13 Upgrade and Maintenance
- 6.5.14 Device Debugging
- 6.5.15 Component Status
- 6.5.16 Log Query
- 6.5.17 Certificate Management
- Chapter 7 Client Software Configuration
- 7.1 Configuration Flow of Client Software
- 7.2 Device Management
- 7.3 Group Management
- 7.4 Person Management
- 7.5 Configure Schedule and Template
- 7.6 Set Access Group to Assign Access Authorization to Persons
- 7.7 Configure Advanced Functions
- 7.8 Door/Elevator Control
- Appendix A. DIP Switch
- Appendix B. Button Configuration Description
- Appendix C. Event and Alarm Type
- Appendix D. Table of Audio Index Related Content
- Appendix E. Error Code Description
- Appendix F. Communication Matrix and Device Command
1.
Enter the Access Control module.
2.
On the navigaon bar on the le, enter Advanced Funcon → More Parameters .
3.
Select an access control device in the device list and click Face Recognion Terminal.
4.
Set the parameters.
Note
These parameters displayed vary according to dierent device models.
COM
Select a C
OM port for conguraon. COM1 refers to the RS-485 interface and COM2 refers to
the RS-232 interface.
Face Picture Database
select Deep Learning as the face picture database.
Authencate by QR Code
If enabled, the device camera can scan the QR code to authencate. By default, the funcon
is disabled.
Blocklist Authencaon
If enabled, the device will compare the person who want to access with the persons in the
blocklist.
If matched (the person is in the blocklist), the access will be denied and the device will upload
an alarm to the client.
If mismatched (the person is not in the blocklist), the access will be granted.
Save Authencang Face Picture
If enabled, the c
aptured face picture when authencang will be saved on the device.
MCU Version
View the device MCU version.
5.
Click Save.
Set RS-485 Parameters
You can set the access control device's RS-485 parameters including the baud rate, data bit, the
s
top bit, parity type, ow control type, communicaon mode, work mode, and connecon mode.
Before You Start
Add access control device to the client, and make sure the device supports RS-485 interface.
Steps
1.
Enter the Access Control module.
2.
On the navigaon bar on the le, enter Adv
anced Funcon → More Parameters .
3.
Select an access control device in the device list and click RS-485 to enter the RS-485 Sengs
page.
DS-K3B220X Series Swing Barrier User Manual
86