User's Manual
Table Of Contents
- Chapter 1 Overview
- Chapter 2 Installation
- Chapter 3 Disassembling before Maintenance
- Chapter 4 Wiring
- 4.1 Components Introduction
- 4.2 Wiring Electric Supply
- 4.3 Wiring Interconnecting Cable
- 4.4 Terminal Description
- 4.4.3 Master Control Board Terminal Description
- 4.4.4 Slave Control Board Terminal Description
- 4.4.5 Main Control Board Terminal Description
- 4.4.6 Main Control Board Serial Port ID Description
- 4.4.7 RS-485 Wiring
- 4.4.8 RS-232 Wiring
- 4.4.9 Wiegand Wiring
- 4.4.10 Barrier Control Wiring
- 4.4.11 Alarm Output Wiring
- 4.5 Wiring Lithium Battery (Optional)
- Chapter 5 Device Settings
- Chapter 6 Device Activation
- Chapter 7 Client Operation
- 7.1 Function Module
- 7.2 Access Control Management
- 7.2.1 Adding Access Control Device
- 7.2.2 Viewing Device Status
- 7.2.3 Editing Basic Information
- 7.2.4 RS-485 Settings
- 7.2.5 Authenticating M1 Card Encryption
- 7.2.6 Remote Configuration
- Checking Device Information
- Editing Device Name
- Editing Time
- Setting System Maintenance
- Setting RS-485 Parameters
- Managing Network User
- Managing Remote Control User
- Setting Security
- Configuring Passing Parameters
- Configuring Screen Parameters
- Configuring People Counting Parameters
- Configuring Network Parameters
- Configuring Advanced Network
- Configuring Relay Parameters
- Configuring Audio File
- Operating Relay
- Viewing Relay Status
- 7.3 Organization Management
- 7.4 Person Management
- 7.5 Permission Configuration
- 7.6 Advanced Functions
- 7.7 Searching Access Control Event
- 7.8 Access Control Event Configuration
- 7.9 Door Status Management
- 7.10 Arming Control
- 7.11 Time and Attendance
- Appendix A Tips for Scanning Fingerprint
- Appendix B DIP Switch Description
- Appendix C Table of Audio Index Related Content
Swing BarrierยทUser Manual
121
Appendix B DIP Switch Description
DIP Switch Introduction
There is a group of 8-bit DIP switch on the main controller. As the picture shown below, No.1 to No
8 is from the low bit to the high bit.
When the switch is towards ON, it means the binary value is 1. Otherwise, it is 0.
If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its
decimal value is 12.
DIP Switch Corresponded Functions
The 8-bit DIP switch corresponded functions on the main controller are as follows:
Bit
Device Mode
Function
Decimal
Value
Binary
Value
1 to 2
Work Mode
Normal Mode
0
00
Study Mode
1
01
Test Mode
2
10
3
Memory Mode
Enable Memory Mode
0
0
Disable Memory Mode
1
1
4
Keyfob Paring Mode
Enable Keyfob Paring Mode
0
0
Disable Keyfob Paring Mode
1
1
5 to 8
Passing Mode
Controlled Bi-direction
0
0000
Controlled Entrance and Prohibit
Exit
1
0001
Controlled Entrance and Free Exit
2
0010
Free Bi-direction
3
0011
Free Entrance and Controlled Exit
4
0100
Free Entrance and Prohibit Exit
5
0101
Prohibited Bi-direction
6
0110
Prohibit Entrance and Controlled
Exit
7
0111
Prohibit Entrance and Free Exit
8
1000