DS-K3G411 Series Tripod Turnstile User Manual
DS-K3G411 Series Tripod Turnstile User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K3G411 Series Tripod Turnstile User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles.
DS-K3G411 Series Tripod Turnstile User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K3G411 Series Tripod Turnstile User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K3G411 Series Tripod Turnstile User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K3G411 Series Tripod Turnstile User Manual This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
DS-K3G411 Series Tripod Turnstile User Manual • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
DS-K3G411 Series Tripod Turnstile User Manual Available Models Product Name Tripod Turnstile Model DS-K3G411 viii
DS-K3G411 Series Tripod Turnstile User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Main Features ........................................................................................................................ 1 Chapter 2 System Wiring ..........
DS-K3G411 Series Tripod Turnstile User Manual Chapter 6 Activation ................................................................................................................. 35 6.1 Activate via SADP ................................................................................................................. 35 6.2 Activate Device via Client Software ...................................................................................... 36 Chapter 7 Client Software Configuration ...................
DS-K3G411 Series Tripod Turnstile User Manual 7.4.15 Export Person Information ........................................................................................ 58 7.4.16 Export Person Pictures .............................................................................................. 59 7.4.17 Get Person Information from Access Control Device ................................................ 59 7.4.18 Move Persons to Another Organization ............................................................
DS-K3G411 Series Tripod Turnstile User Manual 7.10.1 Enable Receiving Event from Devices ....................................................................... 88 7.10.2 View Real-Time Events .............................................................................................. 88 7.10.3 Search Historical Events ............................................................................................ 90 7.11 Remote Configuration via Client Software ...............................................
DS-K3G411 Series Tripod Turnstile User Manual Chapter 1 Overview 1.1 Introduction The tripod turnstile is designed to detect unauthorized entrance or exit. By adopting the turnstile integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc. 1.
DS-K3G411 Series Tripod Turnstile User Manual • • • • Opens/Closes barrier according to the schedule template Up to 3000 visitor cards and up to 60,000 cards except for visitor cards can be added Up to 180,000 presenting card events can be recorded Adjustable strip light brightness 2
DS-K3G411 Series Tripod Turnstile User Manual Chapter 2 System Wiring The preparation before installation and general wiring. Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals. Note The distance between the nearest two line is 581+200 mm. L represents the lane width. 3. Slotting on the installation surface and dig installation holes according to the hole position diagram.
DS-K3G411 Series Tripod Turnstile User Manual • • • • Note The suggested inner diameter of the low voltage conduit is larger than 30 mm. If the face recognition module are required to be connected on the left lane, you should increase the conduit diameter or bury another conduit for the external cables. You should bury one network cable and one high voltage conduit for the right and middle lane. The network cable must be CAT5e or the network cable has better performance.
DS-K3G411 Series Tripod Turnstile User Manual Chapter 3 Installation 3.1 Disassemble Pedestals Before installation, you should use the key to open the pedestals. View the pictures below to find the lock holes. Figure 3-1 Lock Holes 3.2 Install Pedestals Before You Start Prepare for the installation tools, check the device and the accessories, and clear the installation base. Steps Note • The device should be installed on the concrete surface or other non-flammable surfaces.
DS-K3G411 Series Tripod Turnstile User Manual Face recognition terminal installed: If the installation area is too close to the wall, make sure the distance between the pedestal and the wall should be more than 20 mm, or the surface may be scratched. • The dimension is as follows.
DS-K3G411 Series Tripod Turnstile User Manual Figure 3-2 Dimension 1. Prepare for the installation tools, check the components, and prepare for the installation base. 2. Drill holes on the ground according to the installation holes on the pedestals and insert the expansion sleeves. 3. Seal the bottom of the turnstile to avoid water from entering. Note Make sure the installation holes on the pedestals and the base are aligned with each other. 4. Secure the pedestals with expansion bolts.
DS-K3G411 Series Tripod Turnstile User Manual Figure 3-3 Installation Footprint 8
DS-K3G411 Series Tripod Turnstile User Manual Chapter 4 General Wiring 4.1 Components Introduction By default, basic components of the turnstile are connected well. The turnstile supports wiring the AC electric supply for the whole system's power supply. Note The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz. The picture displayed below describes each component's position on the turnstile. Figure 4-1 Components Diagram 1 4.
DS-K3G411 Series Tripod Turnstile User Manual Warning Terminal PE should connect to a ground wire to avoid hazard when people touching the device. Note • The cable bare part should be no more than 8 mm. If possible, wear an insulation cap at the end of the bare cable. Make sure there’s no bare copper or cable after the wiring. • The Terminal L and the Terminal N cannot be wired reversely. Do not wire the input and output terminal reversely.
DS-K3G411 Series Tripod Turnstile User Manual Figure 4-2 Open Side Panel 2. Connect the network cable with the network switch.
DS-K3G411 Series Tripod Turnstile User Manual 4.4 Terminal Description 4.4.
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Alarm Output 2 Terminal Name IN Audio Input NO/NC2 Alarm Output Relay 2 (Dry Contact) COM2 Alarm Output 1 NO/NC1 COM1 Door Lock 2 D2+ D2- Door Lock 1 D1+ D1- Exit Button Description K1 Alarm Output Relay 1 (Dry Contact) Door 2 Relay Output (Dry Contact) Door 1 Relay Output (Dry Contact) Door 1 Signal Input 13 Remark Note The alarm output supports relay output. Note The alarm output supports relay output.
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Terminal Name Description Remark GND Grounding K2 Door 2 Signal Input XF Fire System Input GND Grounding CASE1 Event Alarm Input 1 GND Grounding CASE2 Event Alarm Input 2 Network Interface LAN Network Accessing / Side Light Board / Light Board Accessing / Arm Position Control Board / Arm Position Control Board Accessing / Debugging Port / For Debugging Only / Suction Type Electromagnet / Suction Type Electromagn
DS-K3G411 Series Tripod Turnstile User Manual Interface Name RS-485F/RS-232F RS-485I/RS-232I Terminal Name Description 485F+ RS-485+ Terminal of Face Recognition Terminal Accessing (Default) 485F- RS-485- Terminal of Face Recognition Terminal Accessing (Default) GND Grounding 485I+ RS-485+ Terminal of Face Recognition Terminal Accessing (Default) 485I- RS-485- Terminal of Face Recognition 15 Remark Note • The DIP of RS-485 card ID is set as 1 and 4 by default.
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Terminal Name Description Terminal Accessing (Default) RS-485C/RS-232C Remark is for entering, and 4 is for exiting. • If the visitor card is configured, you should wire two card readers for the exiting side. One's DIP address is 4, and the other is 3. Card Reader 3 can be applied together with the card receiver. The normal user can authenticate on Card Reader 4 and the visitor can authenticate on Card Reader 3.
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Terminal Name Description Remark DIP address is 4, and the other is 3. Card Reader 3 can be applied together with the card receiver. The normal user can authenticate on Card Reader 4 and the visitor can authenticate on Card Reader 3. • You can switch the communication mode between RS-485 and RS-232.
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Wiegand Card Reader 2 Terminal Name Description Remark BZ1 Card Reader Buzzer Control Output W1_1 Wiegand Reading Data Input Data1 W0_1 Wiegand Reading Data Input Data0 GND Grounding OK2 Indicator of Card Note Reader Control Output The Wiegand card (Invalid Card Output) reader 1 refers to the Indicator of Card card reader (entering).
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Terminal Name Color Description PD_485- Blue RS-485- of Light Board Accessing GND Black Grounding 12V Red 12 V Power Terminal PA_485/232+ Yellow RS-485+ of Card Reader Accessing (Default) PA_485/232- Blue RS-485- of Card Reader Accessing (Default) GND Black Grounding TAMPER Brown TAMPER GND Brown Grounding UART 8 (QR Code) 5V Red 5 V Power Terminal Note For RS-232G 232+ Blue RS-232- of QR Code Scanner Accessing (
DS-K3G411 Series Tripod Turnstile User Manual Interface Name Terminal Name Color Description PB_485/232- Yellow RS-232_TX of Fingerprint Recorder Accessing (Default) GND Black Grounding 4.4.2 Main Control Board DIP Switch Description You can set the device mode, switch the communication mode between RS-232 and RS-485, initialize the device via the DIP switch on the main control board. Figure 4-5 DIP Switch on Main Control Board You can set the device mode via the 8-bit DIP switch.
DS-K3G411 Series Tripod Turnstile User Manual The corresponded UART No. of the DIP switch is as follows: Figure 4-6 UART No. Diagram The function of different DIP switches are as follows: Table 4-3 Function of DIP Switch DIP Switch Name 8-bit DIP Switch DIP Switch Bit 1 to 2 (Work Mode) UART No.
DS-K3G411 Series Tripod Turnstile User Manual DIP Switch Name DIP Switch Bit UART No.
DS-K3G411 Series Tripod Turnstile User Manual DIP Switch Name DIP Switch Bit UART No.
DS-K3G411 Series Tripod Turnstile User Manual Figure 4-7 Interface and Corresponded UART No. 4.4.3 RS-485 Wiring Note • When the RS-485 terminal should connect with card reader, the DIP switch for entrance is 1, for exit is 4. • The RS-485 ID should not be duplicated when connecting to multiple RS-485 devices.
DS-K3G411 Series Tripod Turnstile User Manual Note • There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example. • For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200 AC Client Software. 4.4.
DS-K3G411 Series Tripod Turnstile User Manual 26
DS-K3G411 Series Tripod Turnstile User Manual 4.4.5 Wiegand Wiring Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader. 4.4.6 Barrier Control Wiring By default, the barrier has connected with the main control board. If possible, the device can connect with a third party control board to control the third party barriers. Interface D1 controls barrier opening for entrance, while interface D2 controls barrier opening for exit.
DS-K3G411 Series Tripod Turnstile User Manual Entering Wiring Exiting Wiring 28
DS-K3G411 Series Tripod Turnstile User Manual 4.4.7 Alarm Output Wiring Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) . 4.4.8 Fire Alarm Module Wiring You can view the fire alarm module wiring diagram.
DS-K3G411 Series Tripod Turnstile User Manual Chapter 5 Device Settings You can also set the turnstile to passing mode and memory mode, pair the keyfob, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch on the main control board. • Normal Mode: The device will work properly.
DS-K3G411 Series Tripod Turnstile User Manual Note • You can also pair the keyfob via the client software. For details, see Manage Keyfob User . • Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair. • For details about DIP switch value and meaning, see . 6. Optional: Go to System → User → Keyfob User on the remote control page of the client software to delete the keyfob. 5.2 Initialize Device Steps 1.
DS-K3G411 Series Tripod Turnstile User Manual 3. When the beep stopped, plug the jumper cap back. 4. Disconnect the power and power on the device again. Caution The initialization of the device will restore all the parameters to the default setting and all the device events are deleted. Note Make sure no persons are in the lane when powering on the device. 5.3 Relay Output NO/NC Settings 5.3.
DS-K3G411 Series Tripod Turnstile User Manual 5.3.
DS-K3G411 Series Tripod Turnstile User Manual 34
DS-K3G411 Series Tripod Turnstile User Manual Chapter 6 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 6.
DS-K3G411 Series Tripod Turnstile User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 6.
DS-K3G411 Series Tripod Turnstile User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 7.
DS-K3G411 Series Tripod Turnstile User Manual Chapter 7 Client Software Configuration 7.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 7-1 Flow Diagram of Configuration on Client Software 7.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K3G411 Series Tripod Turnstile User Manual 7.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices.
DS-K3G411 Series Tripod Turnstile User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3G411 Series Tripod Turnstile User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3G411 Series Tripod Turnstile User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3G411 Series Tripod Turnstile User Manual 3. Click Add to open the Add window. 4. Select IP Segment as the adding mode. 5. Enter the required information. Start IP Enter a start IP address. End IP Enter an end IP address in the same network segment with the start IP. Port Enter the device port No. The default value is 8000. User Name By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K3G411 Series Tripod Turnstile User Manual Import Devices in a Batch You can add multiple devices to the client in a batch by entering the device parameters in a predefined CSV file. Steps 1. Enter the Device Management module. 2. Click Device tab on the top of the right panel. 3. Click Add to open the Add window, and then select Batch Import as the adding mode. 4. Click Export Template and then save the pre-defined template (CSV file) on your PC. 5.
DS-K3G411 Series Tripod Turnstile User Manual 7. Click Add to import the devices. 7.2.2 Reset Device Password If you forgot the password of the detected online devices, you can reset the device password via the client. Steps 1. Enter Device Management page. 2. Click Online Device to show the online device area. All the online devices sharing the same subnet will be displayed in the list. 3. Select the device from the list and click on the Operation column. 4. Reset the device password.
DS-K3G411 Series Tripod Turnstile User Manual 7.3.1 Add Group You can add group to organize the added device for convenient management. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Create a group. - Click Add Group and enter a group name as you want. - Click Create Group by Device Name and select an added device to create a new group by the name of the selected device.
DS-K3G411 Series Tripod Turnstile User Manual Before You Start Import the resources to group. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. All the added groups are displayed on the left. 3. Select a group on the group list and click Access Point. The access points imported to the group will display. 4. Click in the Operation column to open the Edit Resource window. 5. Edit the resource name. 6. Click OK to save the new settings. 7.3.
DS-K3G411 Series Tripod Turnstile User Manual Note Up to 10 levels of organizations can be added. 4. Optional: Perform the following operation(s). Edit Organization Hover the mouse on an added organization and click name. to edit its Delete Organization Hover the mouse on an added organization and click to delete it. Show Persons in Sub Organization Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations.
DS-K3G411 Series Tripod Turnstile User Manual Figure 7-2 Configure Basic Information Note Once validity period expired, the credentials and access control settings of the person will be invalid and the person will have no authorization to access the doors\floors. You can click Extend to extend the person's validity period for 1 month, 3 months, 6 months, or 1 year. 5. Confirm to add the person. - Click Add to add the person and close the Add Person window.
DS-K3G411 Series Tripod Turnstile User Manual Figure 7-3 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
DS-K3G411 Series Tripod Turnstile User Manual This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add. The card will be issued to the person. 7.4.
DS-K3G411 Series Tripod Turnstile User Manual Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first. For details, refer to Configure Basic Information . 3. Click Add Face in the Basic Information area. 4. Select Take Photo to enter Take Photo window. 5.
DS-K3G411 Series Tripod Turnstile User Manual 7.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3.
DS-K3G411 Series Tripod Turnstile User Manual 5. Select the model of the connected fingerprint recorder. Note If the fingerprint recorder is DS-K1F800-F, you can click Settings to select the COM the fingerprint recorder connects to. 6. Collect the fingerprint. 1) Click Start. 2) Place and lift your fingerprint on the fingerprint recorder to collect the fingerprint. 3) Click Add to save the recorded fingerprint. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window.
DS-K3G411 Series Tripod Turnstile User Manual For details about setting the door's open duration, refer to Configure Parameters for Door . Add to Blacklist Add the person to the blacklist and when the person tries to access doors/floors, an event will be triggered and send to the client to notify the security personnel. Mark as Visitor If the person is a visitor, set the maximum times of authentications, including access by card and fingerprint to limit the visitor's access times.
DS-K3G411 Series Tripod Turnstile User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 2) In the Custom Information panel, enter the person information. 3) Click Add to add the person and close the Add Person window, or click Add and New to add the person and continue to add other persons. 7.4.
DS-K3G411 Series Tripod Turnstile User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Additional Information panel, enter the additional information of the person, including person's ID type, ID No., job title, etc., according to actual needs. 4. Confirm to add the person. - Click Add to add the person and close the Add Person window.
DS-K3G411 Series Tripod Turnstile User Manual 7.4.14 Import Person Pictures After importing face pictures for the added persons to the client, the persons in the pictures can be identified by an added face recognition terminal. You can either import person pictures one by one, or import multiple pictures at a time according to your need. Before You Start Be sure to have imported person information to the client beforehand. Steps 1. Enter the Person module. 2.
DS-K3G411 Series Tripod Turnstile User Manual 7.4.16 Export Person Pictures You can export face picture file of the added persons and save in your PC. Before You Start Make sure you have added persons and their face pictures to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4.
DS-K3G411 Series Tripod Turnstile User Manual 7.4.18 Move Persons to Another Organization You can move the added persons to another organization if you need. Before You Start • Make sure you have added at least two organizations. • Make sure you have imported person information. Steps 1. Enter Person module. 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5.
DS-K3G411 Series Tripod Turnstile User Manual 2. Select the person you want to report card loss for and click Edit to open the Edit Person window. 3. In the Credential → Card panel, click on the added card to set this card as lost card. After reporting card loss, the access authorization of this card will be invalid and inactive. Other person who gets this card cannot access the doors by swiping this lost card. to cancel the loss. 4.
DS-K3G411 Series Tripod Turnstile User Manual Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E. If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should enable this function and select the sector of the card to encrypt.
DS-K3G411 Series Tripod Turnstile User Manual Note Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K3G411 Series Tripod Turnstile User Manual Note Up to 8 time duration(s) can be set for each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K3G411 Series Tripod Turnstile User Manual 2. Click Add to open the Add window. 3. In the Name text field, create a name for the access group as you want. 4. Select a template for the access group. Note You should configure the template before access group settings. Refer to Configure Schedule and Template for details. 5. In the left list of the Select Person field, select person(s) to assign access authority. 6.
DS-K3G411 Series Tripod Turnstile User Manual 4) View the applying status in the Status column or click Applying Status to view all the applied access group(s). Note You can check Display Failure Only to filter the applying results. The selected persons in the applied access groups will have the authorization to enter/exit the selected doors/door stations with their linked card(s) or fingerprints. 9. Optional: Click to edit the access group if necessary.
DS-K3G411 Series Tripod Turnstile User Manual 7.7.1 Configure Device Parameters After adding the access control device, you can configure the parameters of access control device (access controller), access control points (door or floor), alarm inputs, alarm outputs, card readers and lane controller. Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K3G411 Series Tripod Turnstile User Manual Reserved. If enable the function, the device can recognize the ID card. You can present ID card on the device. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s). Configure Parameters for Door After adding the access control device, you can configure its access point door parameters. Steps 1. Click Access Control → Advanced Function → Device Parameter . 2.
DS-K3G411 Series Tripod Turnstile User Manual Note • The duress code, super code, and dismiss code should be different. • The duress code, super password, and the dismiss code should be different from the authentication password. • The length of duress code, super password, and the dismiss code is according the device, usually it should contains 4 to 8 digits. 5. Click OK. 6. Optional: Click Copy to , and then select the door(s) to copy the parameters in the page to the selected doors(s).
DS-K3G411 Series Tripod Turnstile User Manual If enabling the function, user can present card on the card reader. If disabling the function, the card reader for entrance cannot be used. OK LED Polarity/Error LED Polarity/Buzzer Polarity Set OK LED Polarity/Error LED Polarity/Buzzer LED Polarity of main board according to the card reader parameters. Generally, adopts the default settings. Buzzing Time Set the card reader buzzing time. The available time ranges from 0 to 5,999s.
DS-K3G411 Series Tripod Turnstile User Manual 4. Click OK. 5. Optional: Set the switch on the upper right corner to ON to trigger the alarm output. Configure Parameters for Lane Controller After adding the lane controller to the client, you can configure its parameters for passing through the lane. Steps 1. Click Access Control → Advanced Function → Device Parameter to enter Parameter Settings page. 2.
DS-K3G411 Series Tripod Turnstile User Manual Steps 1. Click Access Control → Advanced Function → Remain Open/Closed to enter the Remain Open/ Closed page. 2. Select the door that need to be configured on the left panel. 3. To set the door status during the work day, click the Week Schedule and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated.
DS-K3G411 Series Tripod Turnstile User Manual 6) Optional: Select the time duration(s) that need to be deleted, and then click in the Operation column to delete the selected time duration(s). 7) Optional: Click in the Operation column to clear all the time duration(s) in the time bar. 8) Optional: Click in the Operation column to delete this added holiday period from the holiday list. 9) Click Save. 5. Optional: Click Copy to to copy the door status settings of this door to other door(s). 7.7.
DS-K3G411 Series Tripod Turnstile User Manual Note For setting the template, refer to Configure Schedule and Template . 3) Select the authentication type as Local Authentication, Local Authentication and Remotely Open Door, or Local Authentication and Super Password from the drop-down list. Local Authentication Authentication by the access control device. Local Authentication and Remotely Open Door Authentication by the access control device and by the client.
DS-K3G411 Series Tripod Turnstile User Manual Note • For each access control point (door), up to four authentication groups can be added. • For the authentication group of which authentication type is Local Authentication, up to 8 person/card groups can be added to the authentication group. • For the authentication group of which authentication type is Local Authentication and Super Password or Local Authentication and Remotely Open Door, up to 7 person/card groups can be added to the authentication group.
DS-K3G411 Series Tripod Turnstile User Manual 6. Set output transformation rule. 1) Click Set Rule to open the Set Output Transformation Rules window. Figure 7-9 Set Output Transformation Rule 2) Select rules on the left list. The selected rules will be added to the right list. 3) Optional: Drag the rules to change the rule order. 4) Click OK. 5) In the Custom Wiegand tab, set the rule's start bit, length, and the decimal digit. 7. Click Save. 7.7.
DS-K3G411 Series Tripod Turnstile User Manual Figure 7-10 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4.
DS-K3G411 Series Tripod Turnstile User Manual Figure 7-11 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 7.7.6 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K3G411 Series Tripod Turnstile User Manual Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Authorization by First Person All authentications (except for the authentications of super card, super password, duress card, and duress code) are allowed only after the first person authorization.
DS-K3G411 Series Tripod Turnstile User Manual Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect. Example Set Card Swiping Path If you select Reader In_01 as the beginning, and select Reader In_02, Reader Out_04 as the linked card readers.
DS-K3G411 Series Tripod Turnstile User Manual Steps Note The function should be supported by the access control device and the card reader. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. Note • The sector ID ranges from 1 to 100.
DS-K3G411 Series Tripod Turnstile User Manual The added access control devices will display in the device list. 2. Select a resource (including device, alarm input, door/elevator, and card reader) from the device list. The event types which the selected resource supports will display. 3. Select the event(s) and click Edit Priority to define the priority for the event(s), which can be used to filter events in the Event Center. 4. Set the linkage actions of the event.
DS-K3G411 Series Tripod Turnstile User Manual Buzzer on Controller The audible warning of access control device will be triggered. Capture An event-related picture will be captured when the selected event happens. Recording An event-related picture will be captured when the selected event happens. Note The device should support recording. Buzzer on Reader The audible warning of card reader will be triggered.
DS-K3G411 Series Tripod Turnstile User Manual 7.8.3 Configure Device Actions for Card Swiping You enable access control device's linkage actions (such as disarming a zone and triggering audio prompt) for the swiping of a specific card, In this way, you can monitor the card holder's behaviors and whereabouts. Steps Note It should be supported by the device. 1. 2. 3. 4. 5. 6. 7. Click Access Control → Linkage Configuration . Select the access control device from the list on the left.
DS-K3G411 Series Tripod Turnstile User Manual The audio prompt will be triggered. And the select audio index related audio content will be played according to the configured play mode. 8. Click Save. When the card (configured in Step 5) swipes on the card reader (configured in Step 6), it can trigger the linked actions (configured in step 7). 9.
DS-K3G411 Series Tripod Turnstile User Manual When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Close Door When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials. Remain Open The door will be unlocked (no matter closed or open). All the persons can access the door with no credentials required.
DS-K3G411 Series Tripod Turnstile User Manual Figure 7-12 Real-time Access Records Note You can right click the column name of access event table to show or hide the column according to actual needs. 2. Optional: Select an access point group from the drop-down list in the upper-right corner to show the real time access records of the selected group. 3. Optional: Check the event type and event status. The detected events of checked type and status will be displayed in the list below. 4.
DS-K3G411 Series Tripod Turnstile User Manual 7.10 Event Center The event information (for example, device offline) received by the client displays. In the Event Center, you can check the detailed information of the real-time and historical events, view the event linked video, handle the events, and so on. Before the client can receive the event information from the device, you need to enable the events of the resource and arm the device first. For details, refer to Enable Receiving Event from Devices .
DS-K3G411 Series Tripod Turnstile User Manual Steps 1. Click Event Center → Real-time Event to enter the real-time event page and you can view the real-time events received by the client. Event Time For encoding device, event time is the client time when it receives the event. For other device types, event time is the time when the event is triggered. Priority Priority represents the emergency degree of the event. 2. Filter the events.
DS-K3G411 Series Tripod Turnstile User Manual Enlarge Video or Picture • Double click the video image to view video in a larger window. • Put the cursor on the picture, and click to view picture in a larger window. Download Captured Picture Hover the cursor on the captured picture, and click the download icon on the lower right corner of the picture to download it to the local PC.
DS-K3G411 Series Tripod Turnstile User Manual Status The handling status of the event. 3. Click Search to search the events according the conditions you set. 4. Optional: Right-click the table header of the event list to customize the event related items to be displayed in the event list. Figure 7-14 Customize Event Related Items to Display 5. Optional: Perform one of the following operations.
DS-K3G411 Series Tripod Turnstile User Manual Download Event Related Picture Hover the cursor on the related picture, and then click the download icon on the upper-right corner of the picture to download it to the local PC. You can set the saving path manually. 7.11 Remote Configuration via Client Software Configure device parameters remotely. 7.11.1 Check Device Information Steps 1. Click Maintenance and Management → Device to enter the device list. 2. Click to enter the remote configuration page. 3.
DS-K3G411 Series Tripod Turnstile User Manual 3. Click System → System Maintenance . 4. Maintain the device. Reboot The device starts rebooting. Restore Default Settings Restore the device settings to the default ones, excluding the IP address. Restore All Restore the device parameters to the default ones. The device should be activated after restoring. 5. Remotely upgrade the device. 1) In the Remote Upgrade part, select an upgrade type.
DS-K3G411 Series Tripod Turnstile User Manual 4. Click Add to add the user. 5. Check Enable in the pop-up window and set the keyfob's serial No. 6. Optional: Enable the Remain Open Status of the turnstile. Note If enabling this function, after the keyfob is matching completed, you can set the barrier as remaining open by using the keyfob. 7. Set the door open direction 8. Click OK. Note Up to 32 keyfob users can be added. 7.11.7 Set Security Steps 1.
DS-K3G411 Series Tripod Turnstile User Manual Screen Position Select the screen's position on the device. If select Exit from the drop-down list, the screen will be installed at the exit position of the device. Screen Model Select the screen model from the drop-down list. Font Size Select the text font size in the screen. Text Orientation Select the text orientation on the screen. Line Spacing Set the space between two lines. Word Spacing Set the space between two words.
DS-K3G411 Series Tripod Turnstile User Manual You can select from Invalid, By IR Detection, and By Authentication Number. None The device will not count people. If the device people counting function is enabled, the people counting function is still disabled. By IR Detection The device will count the people who passing through the device depending on the IR detection. By Authentication Number The device will count the people who authenticating on the device.
DS-K3G411 Series Tripod Turnstile User Manual Note • The imported audio file should be in MEM format. • For details about converting other format of the audio file to MEM format, see the audio conversion manual. • If you use the third part software to create or edit an audio file, the volume of the audio file should be no less than 0 × 68. If the volume is less than the value, it will exceed the loudspeaker's power consumption, so that damage the loudspeaker. 7.11.
DS-K3G411 Series Tripod Turnstile User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.
DS-K3G411 Series Tripod Turnstile User Manual Appendix B. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K3G411 Series Tripod Turnstile User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
DS-K3G411 Series Tripod Turnstile User Manual Appendix C. DIP Switch Description The DIP switch is on the master lane control board. No.1 to No 8 is from the low bit to the high bit. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12.
DS-K3G411 Series Tripod Turnstile User Manual Appendix D.
DS-K3G411 Series Tripod Turnstile User Manual Appendix E. Table of Audio Index Related Content Index Content 1 Authenticated. 2 Card No. does not exist. 3 Card No. and fingerprint mismatch. 4 Passing timeout. 5 No permissions. 6 Authentication time out. 7 Authentication failed. 8 Expired card.
DS-K3G411 Series Tripod Turnstile User Manual Appendix F. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure F-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD21315B