DS-K5032-3XFD Visitor Terminal User Manual
DS-K5032-3XFD Visitor Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K5032-3XFD Visitor Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K5032-3XFD Visitor Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K5032-3XFD Visitor Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K5032-3XFD Visitor Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K5032-3XFD Visitor Terminal User Manual ● ● ● ● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center.
DS-K5032-3XFD Visitor Terminal User Manual Available Model Product Name Visitor Terminal Model DS-K5032-3XFD vii
DS-K5032-3XFD Visitor Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Main Features ........................................................................................................................ 1 Chapter 2 Appearance ...............
DS-K5032-3XFD Visitor Terminal User Manual 7.3 Staff-Service Visitor System .................................................................................................. 23 7.3.1 View and Search Visitor Information .......................................................................... 23 7.3.2 Login ............................................................................................................................ 24 7.3.3 System Settings ....................................................
DS-K5032-3XFD Visitor Terminal User Manual Chapter 1 Overview 1.1 Overview The visitor terminal is designed for visitor management, integrated with temperature measurement, which is mainly applied to enterprises, stations, university campuses, factories, etc. 1.2 Main Features ● ● ● ● ● ● ● ● Android operation system with dual-screen design. Temperature measuring range: 30 °C to 45 °C (86 °F to 113 °F), accuracy: 0.1 ° C, deviation: ± 0.5 °C Recognition distance: 0.3 to 2 m.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the visitor terminal: Figure 2-1 Visitor Terminal Diagram Table 2-1 Description of Face Recognition Terminal No. Description 1 Indicator for Card Presenting 2 Card Presenting Area 3 Visitor Screen 4 Supplement Light 5 Thermographic Module 6 Supplement Light 7 Camera 8 Reserved 9 Reserved 10 USB 2.
DS-K5032-3XFD Visitor Terminal User Manual No. Description Note Supports the USB import function. You can use the interface to upload the event to the client software, etc. 11 USB 2.0 Note The interface can connect with an USB flash drive. You can import the allowlist to the device or export the events to the USB flash drive.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better face recognition, there should be light source in or near the installation environment. Sunlight, wind, hot/cool air from air conditioner and other external factors, which may affect surface temperature, will create the deviation of the temperature measurement.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 4 Wiring The suggested wiring diagram is as follows: Figure 4-1 Wiring Diagram 5
DS-K5032-3XFD Visitor Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K5032-3XFD Visitor Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K5032-3XFD Visitor Terminal User Manual 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address.
DS-K5032-3XFD Visitor Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English. Note You will need to exit the APP and change the Android system language via Google Pinyin Input to the same language you choose for the APP system. 6.2 Set Time Zone You can set a time zone for the device system.
DS-K5032-3XFD Visitor Terminal User Manual Figure 6-2 Time Zone Settings Note ● The time zone will affect the device time. 2. Tap Next. 3. Optional: Tap Skip to skip time zone settings. 4. Optional: Tap PREVIOUS to back to the previous page. 6.3 Set Network Parameters You can set the network for the device. Steps 1. Tap Wired Network or Wi-Fi for your actual needs.
DS-K5032-3XFD Visitor Terminal User Manual Figure 6-3 Select Network Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 7 Basic Operation 7.1 Visitor Check In 7.1.1 Reserved Visitor Check In Visitors can make appointments on the platform in advance and check in by phone number or the visitor code generated for successful reservation. Before You Start Fill in the visitor information on the platform in advance. Steps 1. Tap on the right side of the home page to enter the visitor code or the last 4 digits of the visitor's phone number.
DS-K5032-3XFD Visitor Terminal User Manual 2. Present the card on the card presenting area. The visitor's temperature will be displayed on top of the screen. When authentication is completed, you will enter the visitor check-in information page. to retry authentication, or tap to capture face 3. Optional: If authentication fails, tap picture and measure temperature. Figure 7-2 Failed Authentication 4. Fill in the rest of the visitor information.
DS-K5032-3XFD Visitor Terminal User Manual Before You Start Complete the basic settings and visitor parameter settings. Refer to Set Basic Parameters and Visitor Check In Settings for details. Steps 1. Enroll visitor information. 1) Tap Unreserved Check In in the lower right corner of the home page to enter the visitor check-in page.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-4 Visitor Check In 2) Present the card on the card presenting area for authentication. The visitor's temperature will be displayed on top of the screen. When authentication is completed, you will enter the visitor check-in information page.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-5 Visitor Check-in Information Note If authentication fails, tap and measure temperature.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-6 Failed Authentication 3) Add face picture according to the instruction on the visitor screen. Note ● The system will perform recognition according to the configurations in Settings → Basic Settings . Refer to Set Basic Parameters for details. ● The page and instructions are based on dual-screen devices and are referable for singlescreen devices. ● Go to Visitor Check In Settings and set the visitor information to be displayed.
DS-K5032-3XFD Visitor Terminal User Manual 7.1.3 Offline Check In Check-in for visitors when the device is unconnected to network. Before You Start Complete the basic settings and visitor parameter settings. Refer to Set Basic Parameters and Visitor Check In Settings for details. Steps 1. Enroll visitor information. 1) Tap Offline Check In in the right corner of the home page to enter the visitor check-in page.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-8 Person and ID Comparison 2) Present the card on the card presenting area for authentication. The visitor's temperature will be displayed on top of the screen. Note If authentication fails, tap and measure temperature.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-9 Failed Authentication 3) Add face picture according to the instruction on the visitor screen. Note ● The system will perform recognition according to the configurations in Settings → Basic Settings . Refer to Set Basic Parameters for details. ● The page and instructions are based on dual-screen devices and are referable for singlescreen devices. ● Go to Visitor Check In Settings and set the visitor information to be displayed.
DS-K5032-3XFD Visitor Terminal User Manual 7.2 Visitor Check Out 7.2.1 Check Out via QR Code Scan scan the QR code on the receipt to check out. Steps 1. Scan the QR code on the visitor receipt. Note Visitors should scan the QR code on the receipt. Refer to Printing Receipt Settings for receipt content details. Refer to Visitor Check In Settings for receipt print steps. The check-out window will pop up on the operator screen. 2. Tap Check Out.
DS-K5032-3XFD Visitor Terminal User Manual 7.2.2 Check Out via Card Check out via card. Steps 1. Present the card. The check-out window will pop up on the operator screen. 2. Tap Check Out. 7.2.3 Check Out via Search Record You can search and view the visitor record and check out the visitors. Steps 1. Tap in the top right corner to enter the visitor record page. 2. Optional: Filter visitors by conditions. 3. Tap on the selected visitor to enter the detailed information page. 4. Tap Check Out. 7.2.
DS-K5032-3XFD Visitor Terminal User Manual 7.3.2 Login Steps 1. Tap in the top right corner of the home page. The login window will pop up. 2. Enter the activation password. to display the password. 3. Optional: Tap 4. Tap OK to enter the settings page. Note 5 failed attempts with incorrect password will lock the device for 30 minutes. 7.3.3 System Settings Set Network Parameters You can set wired network or Wi-Fi for the device. Steps 1. Tap in the top right corner of the home page.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-11 Wired Network If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the default gateway, DNS1 and DNS2. Tap to save the settings.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-12 Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. Temperature Measurement Settings You can set the temperature measurement parameters, including temp. detection, unit, Max. temperature, Min. temperature, temperature measurement distance and temp. limit to stop visitor registration. Tap Temperature Settings to enter the Temperature Settings page.
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-13 Temperature Measurement Parameters The available parameters descriptions are as follows: Temp. Detection When enabling the function, the device will authenticate the permissions and at the same time take the temperature. When disabling the device, the device will authenticate the permissions only. Unit Select a temperature unit according to your preference. Over-Temperature Threshold (Max.) Configure the upper limit for temperature measurement result.
DS-K5032-3XFD Visitor Terminal User Manual Set Basic Parameters You can set basic parameters for the device. Tap in the top right corner of the home page. Tap Settings → Basic Settings .
DS-K5032-3XFD Visitor Terminal User Manual Table 7-1 Basic Parameters Parameter Description Visitor Parameters Settings Set visitor parameters. Refer to Set Visitor Parameters for details. Change Password Enter old password and confirm new password. The password here is the activation password. Volume Adjust the voice volume ranging from 0 to 10. The larger the value, the louder the volume. Supplement Light Set the white or IR supplement light's brightness. The brightness ranges from 0 to 100.
DS-K5032-3XFD Visitor Terminal User Manual Tap in the top right corner of the home page. Tap Basic Settings → Visitor Parameters Settings to enter the page. Figure 7-15 Visitor Parameters Settings Tap to enable the functions. Manually Enter Visitor Information When the function is enabled, the staff can input visitor information manually. Person and ID Comparison When the function is enabled, the device will be able to process person and ID comparison.
DS-K5032-3XFD Visitor Terminal User Manual Saving Visitor Records When the function is enabled, visitor information will be recorded for the first-time visit. When revisits, the visitor only need to present his/her credential for the device to read and the information will be displayed on screen. Auto Check Out When the function is enabled, system will check out all visitors at 24 o'clock every day. Visitor Code Length You can set the visitor code length of 4 or 6 digits.
DS-K5032-3XFD Visitor Terminal User Manual 2. Tap Export Captured Picture or Export Visitor Records to export the picture captured or visitor information recorded on the device to your USB flash drive. System Maintenance You can view the device information, restore the system to factory settings or default settings, reboot the device, exit the system and start wizard. Tap in the top right corner of the home page. Tap Settings → System Maintenance .
DS-K5032-3XFD Visitor Terminal User Manual All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect. About You can view the device information. Note The page may vary according to different device models. Refers to the actual page for details. Exit Tap Exit to exit the application. Start Wizard Tap Start Wizard for language settings, time zone settings and network settings.
DS-K5032-3XFD Visitor Terminal User Manual Select Language Figure 7-18 Select Language Page Select a language according to your actual needs. By default, the language is English. Note After you change the system language, the device will reboot automatically. Tap Next.
DS-K5032-3XFD Visitor Terminal User Manual Set Time Zone Figure 7-19 Set Time Zone Select a time zone according to your actual needs. Note The time zone will affect the device time. Tap Next.
DS-K5032-3XFD Visitor Terminal User Manual Set Network Figure 7-20 Set Network Select Wired or Wireless. Note Disconnect the wired network before connecting a Wi-Fi. Wired Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wireless Select a Wi-Fi and enter the Wi-Fi's password to get connected. Tap OK.
DS-K5032-3XFD Visitor Terminal User Manual Steps 1. Tap in the top right corner of the home page. Tap Custom Settings → Visitor Check in Settings .
DS-K5032-3XFD Visitor Terminal User Manual Figure 7-21 Visitor Check in Settings Page 2. Set the target items as Required, Not Required or Hide.
DS-K5032-3XFD Visitor Terminal User Manual Visitor Name Visitor name that the visitor needs to fill in when checking in. Gender Visitor's gender that the visitor needs to fill in when checking in. Temp. Visitor's temperature that the visitor needs to fill in when checking in. Phone Visitor's phone No. that the visitor needs to fill in when checking in. Credential Type Visitor's credential type that the visitor needs to fill in when checking in.
DS-K5032-3XFD Visitor Terminal User Manual The remark content that the visitor needs to fill in when checking in. Custom 1/2/3 Customize visitor's check in information. Printing Receipt Settings Set the printing contents on the receipt. Steps 1. Tap in the top right corner of the home page. Tap Custom Settings → Printing Receipt Settings . Figure 7-22 Printing Receipt Settings 2. Enable/disable Print Visitor Receipt with ID Photo.
DS-K5032-3XFD Visitor Terminal User Manual You can view the current logo picture. 2. Plug in the USB flash drive. Note The supported USB flash drive format is FAT32. 3. Tap Add and select a logo picture from the USB flash drive. Note The supported file size is less than 100 KB. The added picture will be cropped to 400 × 400. 4. Optional: Tap Restore Default, the device will use the default logo. 5. Optional: Tap Add Again, you can select the logo picture again. 6.
DS-K5032-3XFD Visitor Terminal User Manual Note The supported USB flash drive format is FAT32. 3. Tap Add, select a picture to add. Note The supported file size is less than 120 kb. The added picture will be cropped to 1280 × 800. 4. Optional: Tap Restore Default, the device will use the default picture for the screen saver. 5. Optional: Tap Add Again, you can select the picture again. 6. Optional: Tap on the upper left corner, you can exit the page.
DS-K5032-3XFD Visitor Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-1 Add User Add the person's basic information, including the employee ID, the person's name, the role, and the organization. Click Save to save the settings.
DS-K5032-3XFD Visitor Terminal User Manual 8.3 Configuration 8.3.1 View Device Information View the device name, language, model, serial No., firmware version, web version, plugin version, number of channels, number of alarm output, device capacity, etc. Click Configuration → System → System Settings → Basic Information to enter the configuration page. You can view the device name, language, model, serial No.
DS-K5032-3XFD Visitor Terminal User Manual NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.3.3 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-3 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4.
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-4 Upgrade and Maintenance Page Click Reboot to reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K5032-3XFD Visitor Terminal User Manual Note Do not power off during the upgrading. 8.3.6 Security Mode Settings Set the security mode for logging in the client software. On the Device for Management page, click Configuration → System → Security → Security Service . Select a security mode from the drop-down list, and click Save. Security Mode High security level for user information verification when logging in the client software.
DS-K5032-3XFD Visitor Terminal User Manual your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 8.3.8 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → User Management → Arming/Disarming Information .
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-5 TCP/IP Settings Page Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, Mac address, and MTU. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, the IPv4 default gateway automatically. NIC Type Select a NIC type from the drop-down list. By default, it is Auto.
DS-K5032-3XFD Visitor Terminal User Manual Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Port Parameters Set the HTTP, RTSP, HTTPS and Server port parmaeters. Click Configuration → Network → Basic Settings → Port . HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. RTSP It refers to the port of real-time streaming protocol.
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's name, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click Network Settings.
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-7 WLAN Settings 2) Set the IP address, subnet mask, and default gateway. Or check Enable DHCP and the system will allocate the IP address, subnet mask, and default gateway automatically. 5. Click Save. 8.3.10 Set Audio Parameters Set the image quality, resolution, and the device volume. Set Audio Parameters Click Configuration → Video/Audio → Audio .
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-8 Set Audio Parameters Drag the block to adjust the output volume. Click Save to save the settings after the configuration. You can also enable Voice Prompt. Note The functions vary according to different models. Refers to the actual device for details. 8.3.11 Set Image Parameters Set brightness, contrast, saturation and hue parameters. Steps 1. Click Configuration → Image . 2. Configure the parameters to adjust the image.
DS-K5032-3XFD Visitor Terminal User Manual Start/end recording video. Capture the image. 3. Click Default to restore the parameters to the default settings. 8.3.12 Set Authentication Parameters Click Configuration → General → Authentication Settings . Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration. Figure 8-9 Authentication Settings Card Reader Select Main Card Reader.
DS-K5032-3XFD Visitor Terminal User Manual You can set the interval between 2 continuous recognition of a same person during the authentication. In the configured interval, Person A can only recognized once. If another person (Person B) has recognized during the interval, Person A can recognized again. 8.3.13 Temperature Measurement Settings You can set the temperature measurement parameters, including unit, Max. temperature, Min. temperature and temperature measurement distance.
DS-K5032-3XFD Visitor Terminal User Manual Edit the distance according to actual situation. The person needs to approach within the set value to trigger the temperature measurement. 4. Click Save. 8.3.14 Set Biometric Parameters Set Basic Parameters Click Configuration → Smart → Smart . Note The functions vary according to different models. Refers to the actual device for details. Figure 8-11 Smart Settings Page Click Save to save the settings after the configuration.
DS-K5032-3XFD Visitor Terminal User Manual Live Face Detection Security Level After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication. Application Mode Select either others or indoor according to actual environment. Continuous Face Recognition Interval Set the time interval between two continuous face recognitions when authenticating. Pupillary Distance Set the pupillary distance when starting face authentication.
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-12 Logo Management 2. Click to add a local image. 3. Click Import to import the selected logo image. Note The logo image shall be no larger than 100 kb with a resolution of 400 × 400. 4. Optional: Click Delete to delete the selected logo image. Set Visitor Basic Information Set visitor basic information. Click Configuration → Visitor → Basic Parameter .
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-13 Visitor Basic Parameters Configure parameters and click Save.
DS-K5032-3XFD Visitor Terminal User Manual You can enter visitor information manually when the function is enabled. ID Card Comparison Threshold Drag the block or enter the value to adjust the card comparison threshold. The higher the value is, the more unlikely for device to mismatch. Auto Check-out The system will auto check out all visitors at 24 o'clock every day when the function is enabled. Saving Visitor Records When saving visitor records is enabled, the visitor's information will be recorded.
DS-K5032-3XFD Visitor Terminal User Manual Custom Item List 1/2/3 Set custom information for visitor check-in. Set Check In Information Select items that will be displayed on the visitor check-in page. Click Configuration → Visitor → Visitor Check In Settings . Figure 8-14 Visitor Check In Settings Select the visitor information items as required at the Required column. Select the visitor information items as display at the Display column. Click Save.
DS-K5032-3XFD Visitor Terminal User Manual Set Printing Receipt Information Select items to be printed on the receipt. Click Configuration → Visitor → Printing Receipt Settings . Figure 8-15 Printing Receipt Settings Select the information items to be printed at the Print column. Click or to move the item position printed on the receipt. 8.3.16 Set Screen Saver Picture You can set the screen saver and the sleep time for the device. Click Configuration → Notice Publication .
DS-K5032-3XFD Visitor Terminal User Manual Figure 8-16 Notice Page Screen Saver Picture Click to add a local picture. Note Only JPG and MP4 format are allowed. No more than 10 pictures can be added. Click Upload. Slide Show Interval Drag the block or enter the number to set the slide show interval. The picture will be changed according to the interval. Click Save to save the configurations.
DS-K5032-3XFD Visitor Terminal User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.
DS-K5032-3XFD Visitor Terminal User Manual Appendix B. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K5032-3XFD Visitor Terminal User Manual Appendix C.
DS-K5032-3XFD Visitor Terminal User Manual Appendix D. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure D-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD20494B-A