Video Intercom Face Recognition Door Station User Manual
Video Intercom Face Recognition Door Station User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom Face Recognition Door Station User Manual CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Video Intercom Face Recognition Door Station User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom Face Recognition Door Station User Manual Safety Instruction Warning ● ● ● ● All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Please make sure that the power has been disconnected before you wire, install or dismantle the device.
Video Intercom Face Recognition Door Station User Manual ● ● ● Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. Used batteries may result in pollution to the environment. Dispose of used batteries according to the instructions provided by the battery manufacturer.
Video Intercom Face Recognition Door Station User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Face Recognition Door Station User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Video Intercom Face Recognition Door Station User Manual 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Video Intercom Face Recognition Door Station User Manual Contents 1 Appearance Description ............................................................................. 1 1.1 Appearance of Door Station .............................................................................. 1 1.2 Appearance of Door Station with Fingerprint Module ...................................... 3 2 Terminal and Wiring Description ................................................................ 5 3 Installation ...............
Video Intercom Face Recognition Door Station User Manual 5.2.1 Call Resident ........................................................................................... 25 5.2.2 Call Center .............................................................................................. 26 5.3 Unlock Door .................................................................................................... 26 5.3.1 Unlock by Password ...............................................................................
Video Intercom Face Recognition Door Station User Manual 7.2.1 Add Online Device .................................................................................. 57 7.2.2 Add Device via IP Address ...................................................................... 58 7.2.3 Add Device via IP segment ..................................................................... 58 7.2.4 Add Devices in Batch .............................................................................. 58 7.2.
Video Intercom Face Recognition Door Station User Manual 8.1.1 Create Community Structure .................................................................. 68 8.1.2 Door Station Flash .................................................................................. 68 8.2 Upgrade in Batch ............................................................................................. 71 8.2.1 Add Devices to be Upgraded .................................................................. 72 8.2.
Video Intercom Face Recognition Door Station User Manual 1 Appearance Description 1.1 Appearance of Door Station Front View Figure 1-1 Front View Table 1-1 Description No.
Video Intercom Face Recognition Door Station User Manual No. Description 4 Ambient Light Sensor 5 Loudspeaker 6 Type C Interface Rear View Figure 1-2 Rear View Table 1-2 Description No.
Video Intercom Face Recognition Door Station User Manual 1.2 Appearance of Door Station with Fingerprint Module Front View Figure 1-3 Front View Table 1-3 Description No.
Video Intercom Face Recognition Door Station User Manual No. Description 6 Fingerprint Recognition Zone 7 Button Rear View Figure 1-4 Rear View Table 1-4 Description No.
Video Intercom Face Recognition Door Station User Manual 2 Terminal and Wiring Description Door station can be wired to alarm input interface, alarm input interface, door lock, door contact and so on.
Video Intercom Face Recognition Door Station User Manual 3 Installation Note ● ● Make sure the device in the package is in good condition and all the assembly parts are included. The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. ● Make sure all the related equipment is power-off during the installation. ● Check the product specification for the installation environment. 3.
Video Intercom Face Recognition Door Station User Manual Mounting Template Figure 3-1 Mounting Template The dimensions of the mounting template is 113.5 mm (W) × 214 mm (H).
Video Intercom Face Recognition Door Station User Manual The dimensions of the mounting plate is 113.5 mm (W) × 214 mm (H) × 23.5 mm (D). Gang Box Figure 3-3 Gang Box The dimensions of the gang box is 137.75 mm (W) × 261.2 mm (H) × 41.8 mm (D). 3.1.2 Surface Mounting Steps 1. Paste the mounting template on the wall according to the installation requirements. Drill holes according to the template. Insert the expansion bolts into the screw holes. 2.
Video Intercom Face Recognition Door Station User Manual Figure 3-4 Fix Mounting Plate 3. Wire the device and cover the rear panel with 2 screws. Apply Sillicone sealant among the joints. Figure 3-5 Seal Rear Panel 4. Fix the device to the mounting plate and fix the device with the set screw.
Video Intercom Face Recognition Door Station User Manual Figure 3-6 Fix Device 3.1.3 Flush Mounting with Gang Box Steps 1. Cave an installation hole on the wall. Pull out the cable from the wall.
Video Intercom Face Recognition Door Station User Manual Figure 3-7 Cave Installation Hole Note ● ● The suggested dimension of the installation hole is 137.75 mm (W) × 261.2 mm (H) × 40.8 mm (D). The suggested length of the cables left outside is 250 mm. 2. Install the gang box into the wall. 1) Insert the gang box into the installation hole. Mark the positon of the gang box screw holes with a marker, and take out the gang box.
Video Intercom Face Recognition Door Station User Manual Figure 3-8 Fix Gang Box 3. Remove the mounting ears of the gang box. Figure 3-9 Remove Mounting Ears 4. Wire the device and cover the rear panel with 2 screws. Apply Sillicone sealant among the joint.
Video Intercom Face Recognition Door Station User Manual Figure 3-10 Seal Rear Panel 5. Fix the door station to the gang box with a set screw.
Video Intercom Face Recognition Door Station User Manual 6. Apply Silicone sealant among the joints between the device and the wall to keep the raindrop from entering. 3.2 Install Door Station with Fingerprint Module Note ● ● Accessories that you need to prepare for installation: Mounting template, mounting plate and gang box. Wire the cables during installation. 3.2.1 Installation Accessory Mounting Template Figure 3-12 Mounting Template The dimensions of the mounting template is 113.
Video Intercom Face Recognition Door Station User Manual Mounting Plate Figure 3-13 Mounting Plate The dimensions of the mounting plate is 113.5 mm (W) × 214 mm (H) × 23.5 mm (D).
Video Intercom Face Recognition Door Station User Manual Gang Box Figure 3-14 Gang Box The dimensions of the gang box is 137.75 mm (W) × 335.2 mm (H) × 41.8 mm (D). 3.2.
Video Intercom Face Recognition Door Station User Manual Steps 1. Paste the mounting template on the wall according to the installation requirements. Drill holes according to the template. Insert the expansion bolts into the screw holes. 2. Fix the mounting plate to the wall with 4 supplied screws. Figure 3-15 Fix Mounting Plate 3. Wire the device and cover the rear panel with 2 screws. Apply Sillicone sealant among the joints. Figure 3-16 Seal Rear Panel 4.
Video Intercom Face Recognition Door Station User Manual Figure 3-17 Fix Device 5. Fix the fingerprint module to the device with 2 set screws to complete installaion.
Video Intercom Face Recognition Door Station User Manual 3.2.3 Flush Mounting with Gang Box Steps 1. Cave an installation hole on the wall. Pull out the cable from the wall. Figure 3-19 Cave Installation Hole Note ● ● The suggested dimension of the installation hole is 137.75 mm (W) × 335.2 mm (H) × 40.8 mm (D). The suggested length of the cables left outside is 250 mm. 2. Install the gang box into the wall. 1) Insert the gang box into the installation hole.
Video Intercom Face Recognition Door Station User Manual Figure 3-20 Fix Gang Box 3. Remove the mounting ears of the gang box.
Video Intercom Face Recognition Door Station User Manual 4. Wire the device and cover the rear panel with 2 screws. Apply Sillicone sealant among the joint. Figure 3-22 Seal Rear Panel 5. Fix the door station to the gang box with a set screw. Figure 3-23 Fix Device 6. Apply Silicone sealant among the joints between the device and the wall to keep the raindrop from entering.
Video Intercom Face Recognition Door Station User Manual 4 Activation 4.1 Activate Device Locally You are required to activate the device first by settings a strong password for it before you can use the device. Steps 1. Power on the device to enter the activation page automatically. 2. Create a password and confirm it. Tap Next to finish activation. 4.2 Activate Device via Web Steps 1. The computer and the device should belong to the same subnet. Note Default IP Address: 192.0.0.65. 2.
Video Intercom Face Recognition Door Station User Manual ● Default IP Address: 192.0.0.65. ● Default Port No.: 8000. ● Default User Name: admin. Steps 1. Run the client software, click Maintenance and Management → Device Management → Device to enter the page. 2. Click Online Device. 3. Select an inactivated device and click Activate. 4. Create a password, and confirm the password.
Video Intercom Face Recognition Door Station User Manual 2. Enter the IP address into the address bar of the web browser, and click Enter to enter the activation page. Note The computer and the device should belong to the same subnet. 3. Create and enter a password into the password field. 4. Confirm the password. 5. Click OK to activate the device.
Video Intercom Face Recognition Door Station User Manual 5 Door Station Local Operation 5.1 Door Station Local Configuration Hold the menu page, enter the password and tap OK to enter the configuration page. 5.1.1 User Management 5.2 Video Intercom Operation Door station supports calling users or management center. 5.2.1 Call Resident Call Resident from Main/Sub Door Station Tap any digit button on the main/sub door station page to enter the calling page. Enter the Room No., and tap to call residents.
Video Intercom Face Recognition Door Station User Manual Number of Underground Floor, and set Interface Type as RS-485 or Network Interface. Enable elevator control. In batch configuration tool, tap Door Station Remote Configuration → System → RS-485 to enter RS-485 settings page and set elevator control type. Call Resident from Outer Door Station On the main page of the outer door station, tap Call to enter the calling page. Enter Phase No. + # + Building No. + # + Unit No. + # + Room No.
Video Intercom Face Recognition Door Station User Manual Enter【 # + Password + unlock button】to unlock door. Unlock by Public Password Note Make sure you have created the public password via iVMS-4200 Client Software remotely. On the menu page, tap to enter the calling page. Enter【 # + Password + #】to unlock door. 5.3.2 Unlock by Face Note Make sure that you have added your face picture to the device. Refers to the User Management for details. Face forward at the camera to unlock. 5.3.
Video Intercom Face Recognition Door Station User Manual Steps Note ● Make sure that the door station IP has been added to the indoor station, and the indoor station and the door station can communicate normally. ● Make sure that the door station is connected to the network. ● Make sure to issue the card first and link it to the door station. 1.
Video Intercom Face Recognition Door Station User Manual 6 Remote Configuration via Web 6.1 Live View In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page. Enter the user name and password and click Login to enter the Live View page. Or you can click Live View to enter the page. Figure 6-1 Live View ● You can start/stop live view, capture, record, audio on/off, two-way audio, etc. ● The stream type can be set as main stream or sub stream.
Video Intercom Face Recognition Door Station User Manual Figure 6-2 Add User 1) Enter Person ID, Name, Floor No.andRoom No.. Select Level. 2) Configure Start Time and End Time. 3) Check Administrator and the person added will be able to log in by face recognition. 4) Click Add Card, enter Card No. and select Property. Or you can click Read and place the card on the card-reding zone. 5) Click Capture and make sure the face image of the person can be captured properly.
Video Intercom Face Recognition Door Station User Manual You can manage the linked device on the page. Click Device Management to enter the settings page. Figure 6-3 Device Management Add Device ● ● Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add. Click Import. Enter the information of the device in the template to import devices in batch. Export Click Export to export the information to the PC.
Video Intercom Face Recognition Door Station User Manual Upgrading Status Click Upgrading to view the upgrading status of the devices. Synchronize Click Synchronize and enable Synchronize for device synchronization. Refresh Click Refresh to get the device information. Optional: Set Device Information. ● Click to edit device information. ● Click to delete device information from the list. ● Select Status and Device Type to search devices. 6.
Video Intercom Face Recognition Door Station User Manual Basic Information Click System Settings → Basic Information to enter the settings page. On the page, you can edit Device Name and Device No. Set the Language and System Type according to your needs. You can view the quantities of added users, face pictures and cards in Capacity. Click Save to enable the settings. Time Settings Click System Settings → Time Settings to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 6-4 Maintenance ● Reboot: Click Reboot to reboot the device. ● Default Click Default to restore all parameters to default settings. Restore All Click Restore All to reset all the parameters, except the IP parameters and user information, to the default settings. ● ● ● Export parameters: 1. Select Device Parameters, and click Export to pop up the dialog box. 2. Set and confirm the encryption password. 3. Click OK to export parameters.
Video Intercom Face Recognition Door Station User Manual Authentication Click Security → Authentication to enter the settings page. On the page, you can select RTSP Authenticationaccording to your actual needs. Click Save to enable the settings. Security Service Click Security → Security Service to enter the settings page. On the page, you can enable SSH or ADB remote control according to your actual needs. Click Save to enable the settings.
Video Intercom Face Recognition Door Station User Manual Figure 6-5 Online Users Click Refresh to get the present information. Arming/Disarming Information Click User Management → Arming/Disarming Information to view the information. Click Refresh to get the present information. 6.4.2 Network Settings TCP/IP Settings TCP/IP settings must be properly configured before you operate the device over network. The device supports IPv4. Steps 1.
Video Intercom Face Recognition Door Station User Manual Figure 6-6 TCP/IP Settings 2. Configure the network parameters. - Check DHCP, the device will get the parameters automatically. - Set the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway manually. 3. Configure the DNS server. 4. Edit Alarm Center IP and Alarm Host Port. 5. Click Save to enable the settings. Port Settings Steps 1. Click Network → Basic Settings → Port to enter the settings page. 2. Set the ports of the device.
Video Intercom Face Recognition Door Station User Manual HTTP Port The default port number is 80, and it can be changed to any port No. which is not occupied. HTTPS Port The default port number is 443, and it can be changed to any port No. which is not occupied. RTSP Port The default port number is 554. Server Port The default server port number is 8000, and it can be changed to any port No. ranges from 2000 to 65535. 3. Click Save to enable the settings. SIP Setting Steps 1.
Video Intercom Face Recognition Door Station User Manual 2. Check Enable VOIP Gateway. 3. Configure the SIP parameters. 4. Click Save to enable the settings. FTP Settings Steps 1. Click Network → Advanced → FTP to enter the settings page.
Video Intercom Face Recognition Door Station User Manual 2. Check Enable FTP. 3. Select Server Type. 4. Input the Server IP Address and Port. 5. Configure the FTP Settings, and the user name and password are required for the server login. 6. Set the Directory Structure, Parent Directory and Child Directory. 7. Set the picture naming rules. 8. Click Save to enable the settings. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1.
Video Intercom Face Recognition Door Station User Manual Note ● ● The verification code is used when adding devices to the mobile client. It can be modified. Please keep it properly. The verification code should contain 6 to 12 characters (it is recommended to be the combination of numeric and letter, and more than 8 characters). HTTP Listening Click Configuration → Network → Advanced → HTTP Listening to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Stream Type Select the stream type to main stream or sub stream. Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. Resolution Select the resolution of the video output. Bitrate Type Select the bitrate type to constant or variable. Video Quality When bitrate type is selected as Variable, 6 levels of video quality are selectable.
Video Intercom Face Recognition Door Station User Manual Figure 6-11 Audio Settings 2. Configure the stream type and the audio encoding type. Stream Type Select the stream type to main stream or sub stream. Audio Encoding The device support G.711ulaw and G.711 alaw. 3. Adjust the Input Volume and Output Volume. Note Available range of volume: 0 to 10. 4. Click Save to save the settings. 6.4.4 Display Settings Configure the image adjustment, backlight settings and other parameters in display settings.
Video Intercom Face Recognition Door Station User Manual Contrast describes the contrast of the image, which ranges from 1 to 100. Saturation Saturation describes the colorfulness of the image color, which ranges from 1 to 100. Sharpness Sharpness describes the edge contrast of the image, which ranges from 1 to 100. 4. Click Save to enable the settings. 6.4.
Video Intercom Face Recognition Door Station User Manual Figure 6-12 Motion Detection 2. Slide Enable Motion Detection to enable the function. 3. Click Draw Area. Click and drag the mouse on the live video to draw a motion detection area. Click Save to save the settings. Clear Area Click X to clear all of the areas. Adjust Sensitivity Move the slider to set the sensitivity of the detection. Note Click to start recording, and click again to stop. Click to capture images. 4.
Video Intercom Face Recognition Door Station User Manual 6. Click Linkage Method to enable the linkages. Notify Surveillance Center Send an exception or alarm signal to the remote management software when an event occurs. 7. Click Save to enable the settings. Event Linkage Steps 1. Click Event → Basic Event → Event Linkage to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 6-13 Event Linkage 2. Select the Major Type as Device Event or Door Event. 3. Select the Minor Type. - For device event, select Minor Type as Tampering Alaem, Fire Input Alarm or Fire Input Resume. - For door event, select Minor Type as Door Open Timed Out (Door Contact). 4. Select the type of the Normal Linkage for the event. 5. Click Save to enable the settings.
Video Intercom Face Recognition Door Station User Manual 6.4.6 Intercom Settings Device ID Configuration Steps 1. Click Device No. to enter the page. Figure 6-14 Device ID Settings 2. Select the device type from the drop-down list, and set the corresponding information. 3. Click Save to enable the device number configuration. Note ● ● ● ● For main door station (D series or V series), the serial No. is 0. For sub door station (D series or V series), the serial No. cannot be 0. Serial No.
Video Intercom Face Recognition Door Station User Manual Steps 1. Go to Intercom → Session Settings to enter the settings page. 2. Set Register Number and Registration Password. 3. Set Main Station IP and VideoIntercom Server IP. 4. Enable Protocol 1.0. 5. Click Save to enable the settings. Time Parameters Click Intercom → Time Parameters to enter the page. Configure the time parameters and click Save. Note ● ● For door station, maximum speaking time and maximum message time should be configured.
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Access Control → Password Settings to enter the settings page. Figure 6-15 Password Settings 2. Select Password Type. 3. Enter and confirm the password. 4. Click Save to enable the settings. Door Parameters Steps 1. Click Access Control → Door Parameters to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 6-16 Door Parameters 2. Select Door No., and edit the Name. 3. Set Lock Action Time. 4. Select Door Contact as Remain Closed or Remain Open. 5. Click Save to enable the settings. Card Security Click Access Control → Card Security to enter the settings page. Slide to enable card encryption parameters. Click Save to enable the settings. Elevator Control Before You Start Make sure that the door station is in the mode of main door station.
Video Intercom Face Recognition Door Station User Manual Figure 6-17 Elevator Control 2. Check to enable elevator control function. 3. Select an Elevator No., and select an elevator controller type for the elevator. 4. Select Interface Type. Note If you select Interface Type as RS-485, you only need to enter Negative Floor Capacity. 5. Enter Negative Floor Capacity, and select Alarm Receiver Type. 6. Enter the elevator controller's Server IP Address, Port No., User Name, and Password. 7.
Video Intercom Face Recognition Door Station User Manual Note ● Up to 4 elevator controllers can be connected to one door station. ● Up to 10 negative floors can be added. ● Make sure the interface types of elevator controllers, which are connected to the same door station are consistent. RS-485 Settings Set the working mode to linked device. Steps 1. Click Access Control → RS-485 to enter the settings page. Figure 6-18 RS-485 Settings 2. Select the No. 3. Select the working mode. 4.
Video Intercom Face Recognition Door Station User Manual Figure 6-19 Smart Settings Table 6-1 Face Capture Advanced Parameters Parameter Description Face Anti-spoofing Enable face anti-spoofing to detect real people face for recognition. After enabling face anti-spoofing function, you can set the Live Face Detection Security matching security level when performing live face Level authentication. Recognition Distance Set the valid distance between the user and the camera when authenticating.
Video Intercom Face Recognition Door Station User Manual Parameter Description Face Recognition Timeout Value When the face recognition time exceed the value you set, the recognition will be determined as a timeout operation. Note You can input the number from 1 to 20. ECO Settings After enabling the ECO mode, the device will use the IR camera to authenticate faces in the low light or dark environment. And you can set the ECO mode threshold, ECO mode (1:N).
Video Intercom Face Recognition Door Station User Manual 6.4.9 Theme Settings Set the advertisement on the main page of the device. Steps 1. Click Configuration → Theme to enter the settings page. 2. Check to enable screen saving function. 3. Set the advertisement theme. 1) Click + Add Theme. 2) Create a theme name, and select the advertisement body as picture or Video. 3) Click Save. 4. Click + to select a picture from the local as the material to be played in standby, and click upload. 5.
Video Intercom Face Recognition Door Station User Manual 7 Remote Configuration via Client Software You can set Video Intercom system and manage video intercom products including indoor station, door station and main station via iVMS-4200 client software. 7.1 Edit Device Network Parameters Before You Start Before configuring the device remotely, make sure that the device is activated. Steps 1. On the person management page, click Online Device. 2. Click to pop up the network parameter settings page. 3.
Video Intercom Face Recognition Door Station User Manual 4. Enter the device Name, User Name, Password, and click Add. Note ● ● Only when the doorphone is added to the client software, you can remotely configure the indoor station. Only online devices with the same user name and activation password can support batch activation. After the device is added, the device information will be listed in the device list area. 7.2.2 Add Device via IP Address Steps 1.
Video Intercom Face Recognition Door Station User Manual 4. Select the file and click Add to import. Note The file format for batch import is .csv format. 7.2.5 Add Device Via EHome Steps 1. In the device list area, click Add to pop up the device adding dialog box. 2. Select the adding mode as EHome. 3. Enter the corresponding information of the device: Name, Device Account , and ISUP login key. 4. Click Add. 7.
Video Intercom Face Recognition Door Station User Manual You can add device, modify device, delete device, perform remote configuration, etc. in device management page. The specific method is similar to web configuration . For details, please refer to the iVMS-4200 client user manual. Note ● ● When adding a third-party door station encoding device, the client only supports the management of device information, and does not support direct preview.
Video Intercom Face Recognition Door Station User Manual 7.7.1 Add Person Steps 1. On the main page of the client, click Person Management to enter the person information configuration page. 2. Select an organization in the organization list and click Add on the person panel to pop up the adding person dialog. Note The Person No. will be generated automatically, and it is editable. 3. Set the person basic information. 1) Enter basic information: name, gender, tel, effective period and E-mail address.
Video Intercom Face Recognition Door Station User Manual 3) Click Start to Scan to add the fingerprint. 4) Click Add to save the fingerprint. Note Only some models of the devices support fingerprint function, please refer to the specific product. 6. Click Access Control and check the access control permissions that need to be configured. 7. Linked Device 1) Click Resident Information, and select the device to be bound. 2) Set the floor No. and room No. 8. Click Save to enable the settings. 7.7.
Video Intercom Face Recognition Door Station User Manual Note ● ● ● ● Click Download Template for Importing Person to download the template. The import template contains the following information: person name, gender, department code, certificate type, certificate number, phone number and address. The number of persons can not exceed 5000 in a single import. If the imported person No. already exists in the client database, the system will automatically replace the original person information.
Video Intercom Face Recognition Door Station User Manual 2. Click Settings to set issue card paramrters. - If you set issue card Mode as Local, you need to set Card Issuer, Card Type and Card No., and enable Buzzer and M1 Card Encryption and click OK to issue card. - If you set Issue Card Mode as Remote, select card issuing device, and click OK to issue card. 7.7.6 Permission Settings Add Permissions Steps 1. On the main page of the client, click Access Control → Access Group to enter the settings page. 2.
Video Intercom Face Recognition Door Station User Manual You can call residents on the video intercom page, and the residents can also call the client software through the indoor station. The door station can also call the client software. Steps 1. On the main page, click Access Control → Video Intercom → Video Intercom to enter the video intercom page. 2. Select an organization from the list, and the residents list on the right displays the residents information under the organization. 3.
Video Intercom Face Recognition Door Station User Manual Note ● One video intercom device can only connect with one client software. ● The maximum ring duration can be set from 15 s to 60 s. ● The maximum speaking duration between the client software and indoor station can be set from 120 s to 600 s. 7.8.2 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Access Control → Video Intercom → Call Log to enter the page. 2. Set the search conditions.
Video Intercom Face Recognition Door Station User Manual You can set the information type as all, advertising Information, property information, alarm information or notice information according to your needs. Time Set the start time and end time of a time period to search the logs. 3. Click Save. 4. Optional: You can reset the settings or export the notice after the search. Reset the Settings Click Reset to reset all the configured search conditions.
Video Intercom Face Recognition Door Station User Manual 8 Batch Configuration Tool You can only configure and operate the door station after creating a password for the device activation. Default parameters of door station are as follows: ● Default IP Address: 192.0.0.65. ● Default Port No.: 8000. ● Default User Name: admin. 8.1 Create the Organization Structure In the batch configuration tool settings page, click Flash Rom to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Link Main Door Station Steps 1. Select the community structure. Here takes building 1 (with 1 unit, 1 floor, 2 rooms) as an example. Figure 8-1 Link Main Door Station 2. Set the starting IP address of main door station (The default starting IP is paired with the unit 1 sub door station). 3. Click Calculate to get the end IP address of door station and main door station No. (such as 1-1-1-1).
Video Intercom Face Recognition Door Station User Manual Caution ● ● During the rooting process, if the door station has been activated locally on the device or the configuration tool, the login password entered here is the activation password. During the rooting process, if the door station is not activated, then entering the login password here is to set a password by yourself. At the same time as the rooting, the door station will be activated. Link Sub Door Station Steps 1.
Video Intercom Face Recognition Door Station User Manual 4. Set the corresponding network information. Set the main door station IP address, SIP server IP address, main station IP address, central platform IP address and port No. Set the subnet mask and gateway address. 5. In the online device area, select a door station, enter the login password, and click Root. At this time, the corresponding No. (such as 1-1-1-1) and IP address of the sub door station are generated.
Video Intercom Face Recognition Door Station User Manual 8.2.1 Add Devices to be Upgraded You can add online devices to be upgraded in the same network segment, or add devices to be upgraded by IP address or IP segment. Add Online Device for Upgrading Steps 1. On the batch upgrade page, click Online Devices to open the online device window. 2. Select a device, click Login Device, enter the user name and password, and click OK. Figure 8-4 Add Online Device 3.
Video Intercom Face Recognition Door Station User Manual Steps 1. On the batch upgrade page, click Add via IP to open the IP/IP segment search window. 2. Search and add devices. Search via IP Enter the device IP address and search for the device to be added. Search via IP Segment Enter the device IP segment and search for the device to be added. 3. Click Add Device. 8.2.2 Upgrade Device You can upgrade the device via the file, or upgrade the device online.
Video Intercom Face Recognition Door Station User Manual Figure 8-5 Upgrade by File 2. Select the upgrade file, click Open and Start to Upgrade, and the device starts to upgrade. Note Device will reboot automatically after upgrading.
Video Intercom Face Recognition Door Station User Manual A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD25771B