Video Intercom Card Reader Module Quick Start Guide Scan to get detailed User Manual
Video Intercom Card Reader Module·Quick Start Guide Quick Start Guide ©2018 Hangzhou Hikvision Digital Technology Co., Ltd. This quick start guide is intended for users of card reader module: DS-KD-M (13.56 MHz) and DS-KD-E (125 KHz). Nametag module is the component of the module door station. Use it along with the main unit. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.
Video Intercom Card Reader Module·Quick Start Guide Support Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Card Reader Module·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Card Reader Module·Quick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.
Video Intercom Card Reader Module·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Video Intercom Card Reader Module·Quick Start Guide Cautions Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
Video Intercom Card Reader Module·Quick Start Guide Table of Contents 1 Overview ...................................................................................................... 1 2 Terminal and Wiring ..................................................................................... 2 3 Installation ................................................................................................... 3 3.1 Configure Sub Module Address .................................................................
Video Intercom Card Reader Module·Quick Start Guide 1 Overview Card reader module supports issue cards and unlock door via swiping card. It works together with the main unit and other sub modules. Its appearance is shown as below. Figure 1-1 Card Reader Module Appearance Table 1-1 Appearance Description No.
Video Intercom Card Reader Module·Quick Start Guide 2 Terminal and Wiring The card reader module’s interfaces and terminals as below: Figure 2-1 Terminals and Interfaces Table 2-1 Descriptions of Terminals and Interfaces No.
Video Intercom Card Reader Module·Quick Start Guide 3 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Sub module must work along with the main unit. Set the sub module address before start the installation steps. Make sure the place for surface mounting is flat. Make sure all the related equipment is power-off during the installation.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-1 DIP Switch 2. Set the sub module address according to the DIP rules, and install the rubber cover back. Digit 1, 2, 3, 4 are used to coding the sub module address; Digit 5, 6, 7, 8 are reserved. Valid sub module address range is 1 to 8. The No. should be unique for sub modules that connected to the same main unit. The sub module address and corresponding switch status as below.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-2 Front and Side View The dimension of one module mounting frame is: 117(L)×107(W)×32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2. Chisel 4 holes with drill align to the screw holes on the sticker.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-3 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-4 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low-right. 5. Connect the cables to the corresponding interfaces of the main unit and insert it into the frame.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-5 Insert the Main unit 6. Use the hexagon wrench in the package fix the cover onto the frame. Figure 3-6 Fix the Cover 3.2.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-7 Front and Side View Figure 3-8 Appearance Description 9
Video Intercom Card Reader Module·Quick Start Guide The dimension of one-module gang box is: 115(L)×134(W)×56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 118(L)×108(W)×45.5(D) mm. The suggested length of cables left outside is 100 mm. Figure 3-9 Cave the Installation Hole 2.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-11 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the 4 mounting ears with tool after concrete is dry. Figure 3-12 Remove the Mounting Ears 7. Insert the mounting frame together with the locating plates into the hole, and fix it with 4 expansion bolts. 8. Connect the cables to the corresponding interfaces of the main unit and insert it into the gang box. Figure 3-13 Insert the Main unit 9.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-14 Fix the Cover 3.3 Two-Module Installation 3.3.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-15 Front and Side View The dimension of two-module mounting frame is: 219(L)×107 (W)×32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2. Chisel 4 holes with drill align to the screw holes on the sticker.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-16 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts.
Video Intercom Card Reader Module·Quick Start Guide The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid. 5. Thread the module-connecting line across the thread hole of the frame. Pass the main unit connecting lines across the thread hole to the upper grid. Figure 3-18 Placement of Lines 6. Connect the cables and module-connecting line to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-19 Line Connection Effect Picture 7. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid. Figure 3-20 Insert the Modules 8. Use the hexagon wrench in the package fix the cover onto the frame.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-21 Fix the Cover 3.3.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-23 Appearance Description The dimension of one-module gang box is: 237(L)×134(W)×56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 220(L)×108(W)×45.5(D) mm. The suggested length of cables left outside is 270 mm.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-24 Cave the Installation Hole 2. Remove the plastic sheet of the cable entry which will be used. 3. Insert the gang box into the hole and pull out the cables through the cable entry. Mark the screw holes’ position with a marker, and take out the gang box. Figure 3-25 Mark the Screw Holes 4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-26 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-27 Remove the Mounting Ears 7. Connect wires and insert the modules: a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of the sub module.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-28 Connect Wires and Insert Modules Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 refers to the module-connecting line in the accessory package. 8. Use the hexagon wrench in the package fix the cover.
Video Intercom Card Reader Module·Quick Start Guide 3.4 Three-Module Installation 3.4.1 Three-Module Surface Mounting Installation Frame Figure 3-30 Front and Side View The dimension of two-module mounting frame is: 320.8(L)×107 (W)×32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-31 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts. Figure 3-32 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid.
Video Intercom Card Reader Module·Quick Start Guide 5. Thread the module-connecting lines across the thread holes of the frame. Pass the main unit connecting lines across the thread hole to the top grid.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-33 Placement of Lines 6. Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. Connect the other end of the module-connecting line1 to the input interface of the sub module. Connect two sub modules via module-connecting line 2. Organize the line with cable tie in the package. The suggested line connection picture as below.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-34 Line Connection Effect Picture 7. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid.
Video Intercom Card Reader Module·Quick Start Guide 8. Use the hexagon wrench in the package fix the cover onto the frame. Figure 3-36 Fix the Cover 3.4.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-37 Front and Side View 28
Video Intercom Card Reader Module·Quick Start Guide Figure 3-38 Appearance Description The dimension of one-module gang box is: 338.8(L)×134(W)×56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 321.8(L)×108(W)×45.5(D) mm. The suggested length of cables left outside is 270 mm.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-39 Cave the Installation Hole 2. Remove the plastic sheet of the cable entry which will be used. 3. Insert the gang box into the hole and pull out the cables through the cable entry. Mark the screw holes’ position with a marker, and take out the gang box. Figure 3-40 Mark the Screw Holes 4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-41 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-42 Remove the Mounting Ears 7. Connect wires and insert the modules: a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the Main Unit, then place the Main Unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of Sub Module 1.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-43 Connect Wires and Insert Modules Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 and Cable 3 refer to the module-connecting line in the accessory package. 8. Use the hexagon wrench in the package to fix the cover onto the gang box.
Video Intercom Card Reader Module·Quick Start Guide 3.5 More-than-Three Module Installation 3.5.1 More-than-Three Module Surface Mounting Figure 3-45 Front and Side View It takes two three-module mounting frames. The dimension of three-module mounting frame is: 320.8(L)×107 (W)×32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Paste two Sticker 1 onto the wall.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-46 Chisel Screw Hole 4. Remove the stickers and insert the expansion sleeves into the screw holes. 5. Thread the module-connecting line (400 mm) and grounding line across the thread hole of both frames. Figure 3-47 Place the Grounding Line and Module-Connecting Line There are 6 module-connecting lines in the package: 190 mm *4 and 400 mm*2.
Video Intercom Card Reader Module·Quick Start Guide Take the 400 mm one for this step. The green-yellow line in the package is for grounding. 6. Fix the mounting frame onto the wall with 8 expansion bolts. Figure 3-48 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid.
Video Intercom Card Reader Module·Quick Start Guide 7. Pass the main unit connecting lines across the thread hole to the top grid of the left frame. Thread the module-connecting line (190 mm) across the thread hole of the frame. The lines should be placed as below: Figure 3-49 Placement of Lines 8. Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-50 Line Connection Effect Picture 9. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid on the left.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-51 Insert the Modules 10. Pull the grounding line out and fixed its two end to the screw on the cover. Figure 3-52 Connect the Grounding Line to the Cover 11. Use the hexagon wrench in the package fix the cover onto the frame.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-53 Fix the Cover 3.5.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-54 Front and Side View 40
Video Intercom Card Reader Module·Quick Start Guide Figure 3-55 Appearance Description It takes two three-module gang boxes. The dimension of the gang box is: 338.8(L)× 134 (W)×56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps: 1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 321.8(L)×315(W)×45.5(D) mm. The suggested length of cables left outside is 270 mm.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-56 Cave the Installation Hole 2. Connect the two gang boxes as the below. Figure 3-57 Cave the Installation Hole 3. Remove the plastic sheet of the cable entry which will be used. 4.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-58 Remove the Plastic Sheets 5. Insert the gang boxes into the hole and pull out the cables through the cable entry. Mark the screw holes’ position with a marker, and take out the gang boxes. Figure 3-59 Mark the Screw Holes 6. Chisel 8 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm. 7. Fix the gang boxes with 8 expansion bolts.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-60 Fix the Gang Boxes 8. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-61 Remove the Mounting Ears 9. Pass the grounding line through the cable entries.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-62 Place the Grounding Line The green-yellow line in the package is for grounding. 10. Connect wires and insert the modules. a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the Main Unit, then place the Main Unit into the upper grid of the left gang box. b. Connect the other end of Cable 2 to the input interface of Sub Module 1.
Video Intercom Card Reader Module·Quick Start Guide Figure 3-63 Install Mounting Frames The cables connect to each module shown as below: Figure 3-64 Install Mounting Frames Cable 2,3,5 and 6 are the module-connecting lines (190 mm) in the package.
Video Intercom Card Reader Module·Quick Start Guide Cable 4 is the module-connecting line (400 mm) in the package. Main unit must be put in the top grid. 11. Pull the grounding line out and fixed its two end to the screw on the cover. Figure 3-65 Connect the Grounding Line to the Cover 12. Use the hexagon wrench in the package fix the cover onto the gang box.
Video Intercom Card Reader Module·Quick Start Guide 4 Remote Operation 4.1 Activate Main Unit Card reader module cannot work alone. It need to use together with main unit. You need to activate the main unit first. You can configure and operate the video intercom devices via iVMS-4200. Default parameters of door station are as follows: Default IP Address: 192.0.0.65. Default Port No.: 8000. Default User Name: admin. Steps: 1. Run iVMS-4200, enter Device Management, check the Online Device area. 2.
Video Intercom Card Reader Module·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Video Intercom Card Reader Module·Quick Start Guide The default port No. is 8000. The default IP address of the door station is 192.0.0.65. After editing the network parameters of device, you should add the devices to the device list again. 4.3 Add Device To configure the device remotely, you need to add the device to iVMS-4200. Steps: 1. Select the activated device and click Add to Client. 2. Enter corresponding information, and click Add.
Video Intercom Card Reader Module·Quick Start Guide Device is added to the client, check it in the Device for Management area. You can call corresponding residents by press the call buttons on the nametag module.
Video Intercom Card Reader Module·Quick Start Guide 52 UDB
