Video Intercom Bundle
Video Intercom Bundle Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom Bundle DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
Video Intercom Bundle Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom Bundle Safety Instruction ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Warning All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
Video Intercom Bundle ● ● ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Input voltage should meet both the SELV and the Limited Power Source according to 60950-1 standard. The power supply must conform to LPS. The recommended adaptor models and manufacturers are shown as below.
Video Intercom Bundle Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Video Intercom Bundle under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Video Intercom Bundle Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
Video Intercom Bundle Contents Chapter 1 About this Manual ...................................................................................................... 1 Chapter 2 Introduction ............................................................................................................... 2 Chapter 3 Appearance ................................................................................................................ 3 Chapter 4 Terminal and Wiring Description ................................
Video Intercom Bundle 7.3.1 Add Organization ........................................................................................................ 29 7.3.2 Modify and Delete Organization ................................................................................. 30 7.4 Person Management ............................................................................................................ 30 7.4.1 Add Person ......................................................................................
Video Intercom Bundle Chapter 1 About this Manual Get the manual and related software from or the official website (http://www.hikvision.com).
Video Intercom Bundle Chapter 2 Introduction Features of the hybrid video intercom products: ● User-friendly control with a convenient touch screen. ● Convenient management via the Hik-Connect mobile client. ● More cost-effective options with analog doorbells. ● Easy installation as the doorbell requires no exclusive power supply.
Video Intercom Bundle Chapter 3 Appearance Network Indoor Station Figure 3-1 Appearance of Indoor Station Table 3-1 Description No.
Video Intercom Bundle Doorphone Figure 3-2 Appearance of Doorphone Table 3-2 Description No.
Video Intercom Bundle No.
Video Intercom Bundle Chapter 4 Terminal and Wiring Description 4.
Video Intercom Bundle Interface Description B2+ Power supply for doorphone 2 V2 Video data interface for doorphone 2 A2 Audio data interface for doorphone 2 G Grounding Function For the access of doorphone 2 7
Video Intercom Bundle Doorphone Wiring Figure 4-2 Terminal of Doorphone Table 4-2 Descriptions of Terminal and Interfaces Interface Description B+ Power supply from indoor station V Video output A Audio input/ output Function For the access of indoor station 8
Video Intercom Bundle Interface Description G Grounding NC Door lock relay output/normally closed COM Door lock relay output/common NO Door lock relay output/normally open Function Connect to door lock 4.2 Wiring Description The Typical application is shown as below. Caution Make sure all the related equipment is power-off during the wiring and installation. Typical Application Figure 4-3 Topology ● Note Network indoor station can be connected to LAN(PoE) with Network Cable.
Video Intercom Bundle Chapter 5 Installation 5.1 Install Indoor Station 5.1.1 Wall Mounting with Junction Box Before You Start ● ● ● ● Note Make sure the device in the package is in good condition and all the assembly parts are included. The power supply the indoor station supports is 12 VDC. Please make sure your power supply matches your indoor station. Make sure all the related equipment is power-off during the installation. Check the product specification for the installation environment.
Video Intercom Bundle Figure 5-1 Wall Mounting Plate Steps 1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm (length) × 50 mm (depth). 2. Insert the junction box to the hole chiseled on the wall. 3. Fix the wall mounting plate to the junction box with 2 screws. 4. Hook the indoor station to the wall mounting plate tightly by inserting the plate hooks into the slots on the rear panel of the indoor station, during which the lock catch will be locked automatically.
Video Intercom Bundle Figure 5-2 Wall Mounting with Junction Box 5.1.2 Mounting Indoor Station without Junction Box Before You Start ● ● ● ● Note Make sure the device in the package is in good condition and all the assembly parts are included. The power supply the indoor station supports is 12 VDC. Please make sure your power supply matches your indoor station. Make sure all the related equipment is power-off during the installation. Check the product specification for the installation environment.
Video Intercom Bundle Figure 5-3 Wall Mounting without Junction Box 5.2 Install Doorbell Before You Start ● Make sure you have powered off the main power switch of your home. ● Make sure you have connected power cables of the doorbell. The Dimension of the wall mounting shield is shown below.
Video Intercom Bundle Figure 5-4 Wall Mounting Shield Steps 1. Fix the wall mounting shield to the wall with 3 screws.
Video Intercom Bundle Figure 5-5 Fix Shield to Wall 2. Hook the door station to the shield tightly by inserting the hooks of shield panel into the slots on the rear panel of the door station.
Video Intercom Bundle Figure 5-6 Install Doorphone to Shield 3. Secure the door station with the mounting shield with the set screw.
Video Intercom Bundle Figure 5-7 Fix Doorbell 17
Video Intercom Bundle Chapter 6 Activation 6.1 Connect to Wired Network You can connect the device to the network via connecting network cables. Steps 1. Use the network cable to connect your computer to distributor. 2. Enter the default IP address of the device in the address bar of web browser. What to do next Activate the device and login to configure parameters remotely. 6.2 Activate Indoor Station You can configure and operate the indoor station after creating a password for the device activation.
Video Intercom Bundle Note You can click to enable or disable password reveal. 3. Tap OK to activate the indoor station. Note We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Video Intercom Bundle 6.4 Basic Operation 6.4.1 Set Linked Device IP Linked network parameters refers to the network parameters of devices (like door station, doorphone, main station, center, etc.), to which the indoor station is linked. Linked devices for the indoor station refers to door station, center, main station, and doorphone. With the private SIP protocol, intercom can be realized only when all these devices are in the same network segment with the indoor station.
Video Intercom Bundle Restore the door station via indoor station. Tap to restore the parameters of the door station. Modify the IP address of the linked door station. Tap to edit the IP address of door station. Select the device to link. Edit the network parameters. 5. 6. Set the IP address for SIP Server, Platform IP, Main Station and Main Doorphone. 6.4.2 Call Settings Add Contact Before You Start Wake up the device. Refers to for details. Steps 1.
Video Intercom Bundle Figure 6-4 Add Contact 3. Enter the contact name and room No. Note If you enable the VoIP account functions, you should enter the contact name and the phone number of VOIP account for the standard SIP protocol. 4. Tap OK to save the settings. Note Up to 200 contacts can be added. Call Resident Before You Start Wake up the device. Refers to for details. Steps 1. On the main page of the device, tap Call to enter the residents calling page.
Video Intercom Bundle Figure 6-5 Call Resident 2. Enter the calling number to call. - If you want to call room, the calling number format should be x-x-x-xxx. For example, the calling number of Community 1, Building 2, Unit 3, and Room 405 is 1-2-3-405. Tap the call button to start an audiovisual call. Note The community No. can be omitted. - If you want to call VoIP contact, the calling number should be the phone number of VoIP account.
Video Intercom Bundle Call Indoor Extension from Indoor Extension Enter【0-indoor extension No.】on the indoor extension to start calling the target indoor extension. Receive Call The indoor station and indoor extension can receive calls from the door station, the main station or iVMS-4200 Client. On the call from door station interface, there are 2 unlock buttons: Unlock 1, and Unlock 2.
Video Intercom Bundle 2. Tap a piece of call logs in the list to call back. ● ● ● ● Note Indoor extension does not support this function. The indoor station saves call logs from door station, outer door station, management center and other indoor stations. Hold a piece of call logs, and tap Delete Logs to delete. Tap Clear to delete all pieces of call logs. 6.4.3 Live View On the live view page, you can view the live video of added door station and network camera.
Video Intercom Bundle Note ● On the Call from Door Station page, there are 2 unlock buttons: Unlock 1, and Unlock 2. When you tap Unlock 1, the building gate will open by default. When you tap Unlock 2, the door station connected door will open. ● On the Call from Door Station page, there are 1 capture button. You can tap the button to capture the picture via door station. ● On the Call from Bell or Call from Analog Doorphone page, there 1 unlock button and 1 capture button.
Video Intercom Bundle Chapter 7 Door Station Configuration via Client Software 7.1 Device Management Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 7.1.1 Add Online Device Before You Start Make sure the device to be added is in the same subnet with your computer. Otherwise, please edit network parameters first.
Video Intercom Bundle Figure 7-1 Add to the Client 28
Video Intercom Bundle 7.1.2 Add Device by IP Address Steps 1. Click +Add to pop up the adding devices dialog box. 2. Select IP/Domain as Adding Mode. 3. Enter corresponding information. 4. Click Add. 7.1.3 Add Device by IP Segment You can add many devices at once whose IP addresses are among the IP segment. Steps 1. Click +Add to pop up the dialog box. 2. Select IP Segment as Adding Mode. 3. Enter corresponding information, and click Add. 7.2 Live View via Door Station Steps 1.
Video Intercom Bundle Note Up to 10 levels of organizations can be created. 7.3.2 Modify and Delete Organization You can select the added organization and click to modify its name. You can select an organization, and click X button to delete it. ● ● Note The lower-level organizations will be deleted as well if you delete an organization. Make sure there is no person added under the organization, or the organization cannot be deleted. 7.
Video Intercom Bundle Note The picture should be in *.jpg format. Click Upload Select the person picture from the local PC to upload it to the client. Click Take Phone Take the person's photo with the PC camera. Click Remote Collection Take the person's photo with the collection device. 3. Issue the card for the person. 1) Click Credential → Card . 2) Click + to pop up the Add Card dialog. 3) Select Normal Card as Card Type. 4) Enter the Card No.
Video Intercom Bundle Steps 1. Select the person in the list and click Change Organization. 2. Select the organization to move the person to. 3. Click OK to save the settings. 7.4.4 Import and Export Person Information The person information can be imported and exported in batch. Steps 1. Exporting Person: You can export the added persons' information in Excel format to the local PC. 1) After adding the person, you can click Export Person to pop up the following dialog. 2) Click ...
Video Intercom Bundle ● ● ● Note The person information, including person details, person's fingerprint information (if configured), and the linked card (if configured), will be imported to the selected organization. If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. The gender of the persons will be Male by default. 7.4.6 Issue Card in Batch You can issue multiple cards for the person with no card issued in batch.
Video Intercom Bundle Figure 7-2 Issue Card in Batch 2. Click Settings.
Video Intercom Bundle Figure 7-3 Card Settings 3. Select Card Type and Card No. Type. 4. Click OK to save the settings. Result After issuing the card to the person, the person and card information will display in the Person(s) with Card Issued list.
Video Intercom Bundle 7.4.7 Permission Settings Add Permissions Steps AccessControlInfo → Access Group to enter the page. 1. On the main page, click 2. Click +Add to pop up the adding dialog box. 3. Configure the parameters. 1) Enter the Name of the permission. 2) Select the Template of the schedule. 3) Check the person to Selected according to your needs. 4) Check the device to Selected according to your needs. 4. Click Save. 5. Check the permission and click Apply All to Device.
Video Intercom Bundle 7.5.1 Receive Call from Door Station Steps 1. Select the client software in the page to start calling the client and an incoming call dialog will pop up in the client software. 2. Click Answer to answer the call. Or click Hang Up to decline the call. 3. After you answer the call, you will enter the In Call page. ● ● ● ● Adjust the Volume of Loudspeaker Click to adjust the volume of loudspeaker. Hang Up Click Hang Up to hang up.
Video Intercom Bundle ● ● ● Note Up to 63 characters are allowed in the Subject field. Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB. Up to 1023 characters are allowed in the Information field. 7.5.3 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Call Log to enter the page. Figure 7-4 Search Call Logs 2. Set the search conditions, including call status, device type, start time and end time.
Video Intercom Bundle Click ˅ to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor Station. Or select All Devices to search logs with all device types. Start Time/End Time Click the time icon to specify the start time and end time of a time period to search the logs. Reset the Settings Click Reset to reset all the configured search conditions. Click Search and all the matched call logs will display on this page. 3. 4.
Video Intercom Bundle Appendix A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD28086B
