Network Indoor Station Operation Guide
Network Indoor Station Operation Guide Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Network Indoor Station Operation Guide CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Network Indoor Station Operation Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Network Indoor Station Operation Guide Safety Instruction Warning ● ● ● ● ● ● ● All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
Network Indoor Station Operation Guide ● ● ● ● ● ● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use.
Network Indoor Station Operation Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Indoor Station Operation Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Network Indoor Station Operation Guide 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Network Indoor Station Operation Guide Contents 1 About this Manual ...................................................................................... 1 2 Local Operation .......................................................................................... 2 2.1 Call Settings ....................................................................................................... 2 2.1.1 Add Contact .............................................................................................. 2 2.1.
Network Indoor Station Operation Guide 3.5 Release Notice ................................................................................................ 14 3.6 Search Video Intercom Information ................................................................ 17 3.6.1 Search Call Logs ...................................................................................... 17 3.6.2 Search Notice .......................................................................................... 18 A.
Network Indoor Station Operation Guide 1 About this Manual Get the manual and related software from or the official website (http:// www.hikvision.com). Product Model Network Indoor Station DS-KH6320-TE1(B)/DS-KH6320- WTE1(B )/DS-KH6320 -LE1(B)/DS- KH6350 -TE1/ DS-KH6350-WTE1/DS- KH6360-TE1/DSKH6360-WTE1 Scan the QR code to get the configuration guide for detailed information. Scan the QR code to get the operation guide for detailed information.
Network Indoor Station Operation Guide 2 Local Operation 2.1 Call Settings 2.1.1 Add Contact Steps 1. Tap Call → to enter the contact list page. Figure 2-1 Contact List 2. Tap to pop up the contact adding dialog. 3. Enter the contact name and the room No. 4. Tap OK to save the settings. Note Up to 200 contacts can be added. 2.1.
Network Indoor Station Operation Guide Steps Note Only when the Call Management Center function is enabled, should the call center button be displayed. For details, see the configuration guide. 1. Tap Call → to enter the residents calling page. Figure 2-2 Call Resident 2. Enter the calling number. The calling number format should be x-x-x-xxx. For example, the calling number of Community 1, Building 2, Unit 3, and Room 405 is 1-2-3-405. Note The community No. can be omitted. 3.
Network Indoor Station Operation Guide The indoor station and indoor extension can receive calls from the door station, the main station or iVMS-4200 Client. On the call from door station interface, there are 2 unlock buttons: Unlock 1, and Unlock 2. When you tap Unlock 1, the building gate will open by default, and when you tap Unlock 2, the door connected to the door station with the secure control door unit will open.
Network Indoor Station Operation Guide 2.2 Leave Message You can set leave message, and view the messages. Tap Settings → → Shortcut Settings , and enable Leave Message. Tap Message to view the messages. 2.3 Live View On the live view page, you can view the live video of added door station and network camera. Steps Note ● Make sure the network camera or door station is well-connected. ● Make sure the indoor extension and the indoor station are well-connected. 1.
Network Indoor Station Operation Guide Note ● ● On the Call from Door Station page, there are 2 unlock buttons: Unlock 1, and Unlock 2. When you tap Unlock 1, the building gate will open by default. When you tap Unlock 2, the door station connected door will open. On the Call from Door Station page, there are 1 capture button. You can tap the button to capture the picture via door station. 3. Tap to enter the live view page of network cameras. 2.
Network Indoor Station Operation Guide Figure 2-5 Arm Settings page 2. Select Stay, Away, Sleeping or Custom. 3. Enter the arm/disarm password to enable the scene. Note You can set the arm/disarm password in the general settings. For details, see the configuration guide. 4. Tap OK. Note You can also tap → One-Push to Arm at the upper right corner of the home page to enable the scene. 2.4.2 Disarm Room Steps 1. Tap → One-Push to Disarm at the upper-right corner of the home page to disarm.
Network Indoor Station Operation Guide Figure 2-6 Disarm Room 2. Enter the arm/disarm password. Note You can set the arm/disarm password in the general settings. For details, see the configuration guide. 3. Tap OK. 2.5 Arming Mode Settings 4 arming modes can be configured: stay mode, away mode, sleeping mode and custom mode. Before You Start Tap Settings → → Shortcut Settings to enable Alarm. Steps Note On the home page, the arming status function and zone settings function are hidden by default.
Network Indoor Station Operation Guide Figure 2-7 Arming Mode Settings 3. Arm the selected zone. Note ● ● ● Zones are configurable on the arming mode page. 24H alarm zone including smoke detector zone and gas detector zone will be triggered even if they are disabled. Arming mode settings should be configured with the settings of arming status on the user page of the device. 2.6 Call Elevator The indoor station supports calling the elevator.
Network Indoor Station Operation Guide Figure 2-8 Call Elevator 2. Tap on the home page of the indoor station to start calling the elevator. 3. When the device communicates with door station, tap unlock icon to start calling the elevator. 2.7 Relay Settings After you set the output parameters and display the relay button on the main page, you can control the relay manually. Steps 1. Tap Settings → → Output Settings and disable Hide on Main Page function. 2. Back to the main page and tap . 3.
Network Indoor Station Operation Guide Figure 2-9 Alarm Logs Delete a Log: Hold the item, you can delete it. Clear Logs: Hold the item, you can clear all logs. See Details: Hold a alarm log, you can see the alarm details. Note Indoor extension only supports alarm log and capture log.
Network Indoor Station Operation Guide 3 Remote Operation via the client software The Video Intercom module provides remote control and configuration on video intercom products via the iVMS-4200 client software. 3.1 Call Indoor Station Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Select a resident and click selected resident. in the Call Household column to start calling the Figure 3-1 Calling Indoor Station 3.
Network Indoor Station Operation Guide 3.2 Receive Call from Indoor Station/Door Station Steps 1. Select the client software in the indoor station or door station page to start calling the client and an incoming call dialog will pop up in the client software. Figure 3-2 Incoming Call from Indoor Station 2. Click Answer to answer the call. Or click Hang Up to decline the call. 3. After you answer the call, you will enter the In Call window. ● Click to adjust the volume of the loudspeaker.
Network Indoor Station Operation Guide You can get the live view of the door station and outer door station in the Main View module and control the door station and outer door station remotely. In the Main View module, double-click a door station or outer door station device or drag the device to a display window to start the live view. You can click Unlock on the menu to open the door remotely. 3.
Network Indoor Station Operation Guide You can create different types of notices and send them to the residents. Four notice types are available, including Advertising, Property, Alarm and Notice Information. Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Click Notice to enter the Release Notice page. Figure 3-4 Release Notice 3. Click Add on the left panel to create a new notice.
Network Indoor Station Operation Guide Figure 3-5 Create a Notice 4. Edit the notice on the right panel. 1) Click ... on the Send To field to pop up the Select Resident dialog. 2) Check the checkbox(es) to select the resident(s). Or you can check the All checkbox to select all the added residents. 3) Click OK to save the selection. 4) Enter the subject on the Subject field. Note Up to 63 characters are allowed in the Subject field.
Network Indoor Station Operation Guide Note Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB. 7) Enter the notice content in the Information field. 8) Optional: You can also click Clear to clear the edited content. Note Up to 1023 characters are allowed in the Content field. 5. Click Send to send the edited notice to the selected resident(s). The sent notice information will display on the left panel.
Network Indoor Station Operation Guide Figure 3-6 Search Call Logs 3. Set the search conditions, including call status, device type, start time and end time. Call Status Click to unfold the drop-down list and select the call status as Dialed, Received or Missed. Or select All to search logs with all statuses. Device Type Click to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor Station.
Network Indoor Station Operation Guide Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Click Notice to enter the Notice page. Figure 3-7 Search Notice 3. Set the search conditions, including notice type, subject, recipient, start time and end time. Recipient Input the recipient information in the Recipient field to search the specified notice. Subject Input the keywords in the Subject field to search the matched notice.
Network Indoor Station Operation Guide 6. You can view and edit the notice details, check the sending failed/sent succeeded/ unread users, and resend the notice to sending failed/unread users. 7. Optional: Click Export to export the notices to your PC.
Network Indoor Station Operation Guide A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD26878B
