User's Manual
DS-KH6320-WTPE2
Video Intercom Two-Wire Indoor Staon
Diagram References
ENGLISH
UD17636B
1 2
3
2
1
3 4 5
6
7
Appearance
Installaon
Before you begin:
Wall Mounng with Juncon Box
Acvate Indoor Staon
1
3
Geng Started
4
Wiring
2
Display Screen
Microphone
Debugging Port
1 2 3
4
5 6 7
1. Make sure the device in the package is in good condition and all the assembly
parts are included.
2. The power supply the indoor station supports is 24 VDC. Please make sure your
power supply matches your indoor station.
3. Make sure all the related equipment is power-off during the installation.
4. Check the product specificaon for the installaon environment.
5. Here takes wall mounitng with juncon box for example.
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate hooks
into the slots on the rear panel of the indoor staon, during which the lock catch will be
locked automacally.
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon and tap Next.
a. Select Indoor Staon Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor staon are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the door staon in the list to link.
b. Tap the sengs icon to pop up the Network Sengs page.
c. Edit the network parameters of the door staon manually or enable DHCP to get
the network parameters automacally.
d. Oponal: Enable Synchronize Language to synchronize the Language of door
staon with indoor staon.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
Note: We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following categories:
upper case leers, lower case leers, numbers, and special characters) in order to
increase the security of your product. And we recommend you reset your password
regularly, especially in the high security system, reseng the password monthly or
weekly can beer protect your product.
Loudspeaker
Two-Wire Interface
Alarm Terminal
Power Supply Interface
Note: The debugging port is used for debugging only.
The wall mounng plate and the juncon box are required to install the indoor staon onto
the wall.
The dimension of juncon box should be 75 mm (width) × 75 mm (length) × 50 mm (depth).
The dimension of wall mounng plate is shown.
Refer to Video Intercom Indoor Staon Configuraon Guide (scan the QR code) for details.
Refer to Video Intercom Indoor Staon Operaon Guide (scan the QR code) for details.
You are required to acvate the device first by seng a strong password for it before
you can use the device.
1
Quick Configuraon
2
Wall Mounng without Juncon Box
1. Insert 2 expension tubes into the wall.
2. Fix the wall mounng plate to the wall with 2 screws.
3. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock
catch will be locked automacally.
Product Informaon
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware embodied in the Product is governed by the
user license agreement covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright protecon. Hangzhou Hikvision Digital Technology
Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated,
or distributed, parally or wholly, by any means, without the prior wrien permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the
subject of applicaons for the same by Hikvision and/or its affiliates. Other trademarks menoned in this manual
are the properes of their respecve owners. No right of license is given to use such trademarks without express
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN
RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Data Protecon
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for device with facial
recognion features, biometrics data is stored in your device with encrypon method; for fingerprint device,
only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable
data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard
personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic
reviews and assessments of the effecveness of your security controls.
Scan the QR code to get the configuraon
guide for detailed informaon.
Scan the QR code to get the operaon
guide for detailed informaon.
● All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regulaons
and other related regulaons in your local region.
● Please use the power adapter, which is provided by normal company. The power consumpon cannot be less than the
required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center. Never aempt to
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.)
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the
equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operang temperature),
cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfuncon however), and affecng the endurance of sensor at the same me.
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the
acidic sweat of the fingers may erode the surface coang of the device cover.
● Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline
detergents.
● Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you need to return the device
to the factory with the original wrapper. Transportaon without the original wrapper may result in damage on the device
and lead to addional costs.
● Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used baeries according to the instrucons provided by the baery manufacturer.
Safety Instruction
Cauons
Warnings
122
100
64.85
Unit:mm
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
GND
485-
485+
ALARM IN
RS485
AIN1: Alarm Input 1
AIN2: Alarm Input 2
AIN3: Alarm Input 3
AIN4: Alarm Input 4
AIN5: Alarm Input 5
AIN6: Alarm Input 6
AIN7: Alarm Input 7
AIN8: Alarm Input 8
GND: Grounding
485-: RS-485 Interface
485+: RS-485 Interface
Note: Wiring descripon refers to the User Manual.
Rear Panel (without Interface)
Screw
Wall Mounng Plate
Lock Catch Lock Catch
Lock CatchLock Catch
Juncon Box Wall
Hook
Hook
Hook
Hook
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore
with the applicable harmonized European standards listed under the RE Direcve 2014/53/EU, the EMC
Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU.
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at designated collecon points. For more
informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentaon for specific baery informaon.
The baery is marked with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point.
For more informaon see: www.recyclethis.info
FCC Conditions
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operaon.
EU Conformity Statement
FCC Information
Please take aenon that changes or modificaon not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a
residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee
that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
Please take aenon that changes or modificaon not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operaon.
This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm between the radiator & your body.