Video Intercom Indoor Station Operation Guide
Video Intercom Indoor Station Operation Guide Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom Indoor Station Operation Guide Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of our devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
Video Intercom Indoor Station Operation Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom Indoor Station Operation Guide Safety Instruction ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Warning All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.
Video Intercom Indoor Station Operation Guide ● ● ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Input voltage should meet both the SELV and the Limited Power Source according to 60950-1 standard. The power supply must conform to LPS. The recommended adaptor models and manufacturers are shown as below.
Video Intercom Indoor Station Operation Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Indoor Station Operation Guide under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Video Intercom Indoor Station Operation Guide Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. Power Source Detail The power source should be qualified and meet limited power source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.
Video Intercom Indoor Station Operation Guide Contents Chapter 1 Local Operation .......................................................................................................... 1 1.1 Call Settings ............................................................................................................................ 1 1.1.1 Add Contact .................................................................................................................. 1 1.1.2 Call Resident .....................
Video Intercom Indoor Station Operation Guide Chapter 1 Local Operation 1.1 Call Settings 1.1.1 Add Contact Steps 1. Tap Call → to enter the contact list page. Figure 1-1 Contact List 2. Tap to pop up the contact adding dialog. 3. Enter contact information. ● If you adopt private SIP protocol, enter the contact name and the room No. ● If you adopt standard SIP protocol, enter the contact name and the phone number of VOIP account. 4. Tap OK to save the settings. Note Up to 200 contacts can be added.
Video Intercom Indoor Station Operation Guide 1.1.2 Call Resident Steps Note Only when the Call Management Center function is enabled, should the call center button be displayed. For details, see the configuration guide. 1. Tap Call → to enter the residents calling page. Figure 1-2 Call Resident 2. Enter the calling number. ● When you adopt private SIP protocol, the calling number format should be x-x-x-xxx. For example, the calling number of Community 1, Building 2, Unit 3, and Room 405 is 1-2-3-405.
Video Intercom Indoor Station Operation Guide 1.1.3 Call Indoor Extension/Indoor Station If you install indoor station and indoor extensions at home, you can call the indoor extension via your indoor station, and vice versa. Enter 【0-indoor extension No.】 on the indoor station to start calling. Enter 【0-0】 to call the indoor station from the indoor extension. 1.1.4 Receive Call The indoor station and indoor extension can receive calls from the door station and the main station.
Video Intercom Indoor Station Operation Guide 2. Tap a piece of call logs in the list to call back. ● ● ● Note Indoor extension does not support this function. The indoor station saves call logs from door station, outer door station, management center and other indoor stations. Hold a piece of call logs to open the call logs handling menu. Tap Delete to delete the piece of call logs. Tap Clear to delete all pieces of call logs. 1.2 Leave Message You can set leave message, and view the messages.
Video Intercom Indoor Station Operation Guide Figure 1-4 Live View 2. Tap to enter the live view page of door station. Note ● On the Call from Door Station page, there are 2 unlock buttons: Unlock 1, and Unlock 2. When you tap Unlock 1, the building gate will open by default. When you tap Unlock 2, the door station connected door will open. ● On the Call from Door Station page, there are 1 capture button. You can tap the button to capture the picture via door station. 3.
Video Intercom Indoor Station Operation Guide 1.4.1 Arm Room Steps Note Only when the Alarm shortcut function is enabled, should the call center button be displayed. For details, see the configuration guide. 1. Tap on the home page to enter the scene page. Figure 1-5 Arm Settings page 2. Select Stay, Away, Sleeping or Custom. 3. Enter the arm/disarm password to enable the scene. Note You can set the arm/disarm password in the general settings. For details, see the configuration guide. 4. Tap OK.
Video Intercom Indoor Station Operation Guide 1.4.2 Disarm Room Steps 1. Tap → One-Push to Disarm at the upper-right corner of the home page to disarm. Figure 1-6 Disarm Room 2. Enter the arm/disarm password. Note You can set the arm/disarm password in the general settings. For details, see the configuration guide. 3. Tap OK. 1.5 Arming Mode Settings 4 arming modes can be configured: stay mode, away mode, sleeping mode and custom mode. Before You Start Tap Settings → → Shortcut Settings to enable Alarm.
Video Intercom Indoor Station Operation Guide Steps Note On the home page, the arming status function and zone settings function are hidden by default. You should enable the alarm function first. 1. Back to the home page, tap Settings → → Scene Settings to enter the arming mode settings page. 2. Tap Stay Mode, Away Mode, Sleeping Mode, or Custom to enter the page. Figure 1-7 Arming Mode Settings 3. Arm the selected zone. ● ● ● Note Zones are configurable on the arming mode page.
Video Intercom Indoor Station Operation Guide 1.6 Call Elevator The indoor station supports calling the elevator. Before You Start Enable call elevator via Guarding Vision Client Software. Steps 1. Tap Settings → → Shortcut Settings to enable Call Elevator. Figure 1-8 Call Elevator on the home page of the indoor station to start calling the elevator. 2. Tap 3. When the device communicates with door station, tap unlock icon to start calling the elevator. 1.
Video Intercom Indoor Station Operation Guide 1.8 Information Management You can view public notice, visitor message, alarm log and capture log on information management page. Tap Message on the home page to enter the information management page. (Here takes the alarm log page as an example.) Figure 1-9 Alarm Logs Delete a Log: Hold the item, you can delete it. Clear Logs: Hold the item, you can clear all logs. See Details: Hold a alarm log, you can see the alarm details.
Video Intercom Indoor Station Operation Guide Chapter 2 Remote Operation via the client software The Video Intercom module provides remote control and configuration on video intercom products via the Guarding Vision client software. 2.1 Call Indoor Station Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Select a resident and click in the Call Household column to start calling the selected resident. Figure 2-1 Calling Indoor Station 3.
Video Intercom Indoor Station Operation Guide 2.2 Receive Call from Indoor Station/Door Station Steps 1. Select the client software in the indoor station or door station page to start calling the client and an incoming call dialog will pop up in the client software. Figure 2-2 Incoming Call from Indoor Station 2. Click Answer to answer the call. Or click Hang Up to decline the call. 3. After you answer the call, you will enter the In Call window. ● Click to adjust the volume of the loudspeaker.
Video Intercom Indoor Station Operation Guide 2.3 View Live Video of Door Station and Outer Door Station You can get the live view of the door station and outer door station in the Main View module and control the door station and outer door station remotely. In the Main View module, double-click a door station or outer door station device or drag the device to a display window to start the live view. You can click Unlock on the menu to open the door remotely. 2.
Video Intercom Indoor Station Operation Guide 2.5 Release Notice You can create different types of notices and send them to the residents. Four notice types are available, including Advertising, Property, Alarm and Notice Information. Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Click Notice to enter the Release Notice page. Figure 2-4 Release Notice 3. Click Add on the left panel to create a new notice.
Video Intercom Indoor Station Operation Guide Figure 2-5 Create a Notice 4. Edit the notice on the right panel. 1) Click ... on the Send To field to pop up the Select Resident dialog. 2) Check the checkbox(es) to select the resident(s). Or you can check the All checkbox to select all the added residents. 3) Click OK to save the selection. 4) Enter the subject on the Subject field. Note Up to 63 characters are allowed in the Subject field.
Video Intercom Indoor Station Operation Guide 5) Click in the Type field to unfold the drop-down list and select the notice type. 6) Optional: Click View to add a local picture to the notice. Note Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB. 7) Enter the notice content in the Information field. 8) Optional: You can also click Clear to clear the edited content. Note Up to 1023 characters are allowed in the Content field. 5.
Video Intercom Indoor Station Operation Guide Figure 2-6 Search Call Logs 3. Set the search conditions, including call status, device type, start time and end time. Call Status Click to unfold the drop-down list and select the call status as Dialed, Received or Missed. Or select All to search logs with all statuses. Device Type Click to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor Station.
Video Intercom Indoor Station Operation Guide 2.6.2 Search Notice Steps 1. On the main page, click Access Control → Video Intercom to enter the Video Intercom page. 2. Click Notice to enter the Notice page. Figure 2-7 Search Notice 3. Set the search conditions, including notice type, subject, recipient, start time and end time. Recipient Input the recipient information in the Recipient field to search the specified notice. Subject Input the keywords in the Subject field to search the matched notice.
Video Intercom Indoor Station Operation Guide 6. You can view and edit the notice details, check the sending failed/sent succeeded/unread users, and resend the notice to sending failed/unread users. 7. Optional: Click Export to export the notices to your PC.
UD30010N
