Video Intercom 9 Series Indoor Station Configuration Guide
Video Intercom 9 Series Indoor Station Configuration Guide Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom 9 Series Indoor Station Configuration Guide CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Video Intercom 9 Series Indoor Station Configuration Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom 9 Series Indoor Station Configuration Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom 9 Series Indoor Station Configuration Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Video Intercom 9 Series Indoor Station Configuration Guide 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Video Intercom 9 Series Indoor Station Configuration Guide Contents 1 About this Manual ...................................................................................... 1 2 Local Operation .......................................................................................... 2 2.1 Activate Indoor Station ..................................................................................... 2 2.2 Configuration Settings ................................................................................
Video Intercom 9 Series Indoor Station Configuration Guide 3.4 Remote Configuration ..................................................................................... 19 3.4.1 System .................................................................................................... 19 3.4.2 Video Intercom ....................................................................................... 24 3.4.3 Network ................................................................................................
Video Intercom 9 Series Indoor Station Configuration Guide 1 About this Manual Get the manual and related software from or the official website (http:// www.hikvision.com).
Video Intercom 9 Series Indoor Station Configuration Guide 2 Local Operation 2.1 Activate Indoor Station You can only configure and operate the indoor station after creating a password for the device activation. Steps 1. Power on the device. It will enter the activation page automatically. 2. Create a password and confirm it. 3. Tap OK to activate the indoor station.
Video Intercom 9 Series Indoor Station Configuration Guide Two ways are available for you to set IP address: DHCP, and set IP address manually. 1. Tap Settings → page. → Configuration Settings → to enter the network settings Note Enter activate password as the admin password. Figure 2-2 Network Settings 2. Enable DHCP, then the indoor station can search and get an IP address automatically. Note Skip the following steps if you have enabled DHCP. 3. Set the Local IP, Subnet Mask and Gateway manually. 4.
Video Intercom 9 Series Indoor Station Configuration Guide 1. Tap Settings → → Configuration → to enter the device management page. Note Default admin password is the activation password. Figure 2-3 Device Management 2. Tap Main Door Station to pop up the device information dialog. Figure 2-4 Device Information Restore the door station via indoor station. Tap to restore the parameters of the door station. Modify the IP address of the linked door station. Tap to modify the IP address of door station.
Video Intercom 9 Series Indoor Station Configuration Guide 2.2.3 Set Indoor Station No. Indoor station No. and the indoor extension No. are numbers, which can be dialed by other devices to call the indoor station and the indoor extension in an intercom system. The indoor station No., is composed of the floor No. and the room No. The indoor extension No. should be a numeric from 1 to 5. Up to 5 indoor extensions can be set for 1 indoor station. Steps 1. Tap Settings → page.
Video Intercom 9 Series Indoor Station Configuration Guide Note Default admin password is the activation password. 2. Tap + to pop up the dialog box. 3. Tap Camera and OK to add. Figure 2-6 Add Camera 4. Enter the device name and IP address. 5. Enter the port No. and channel No. 6. Enter the user name and password of the camera. 7. Tap √ to add the camera. 2.2.5 Zone and Alarm Settings Zone Settings You can set the zone type, alarm type and delay time and other parameters of 8 zones.
Video Intercom 9 Series Indoor Station Configuration Guide 1. Tap Settings → → Zone Settings to enter the zone settings page. Figure 2-7 Zone Settings 2. Press a zone to pop up the zone editing dialogue box. 3. Set the zone type, alarm type, status of arming status, entering delay, and exiting delay. 4. Tap OK to save the settings. Note • 7 zone types are selectable: Panic Button, Door Magnetic, Smoke Detector, Active Infrared, Passive Infrared, Gas Detector, and Doorbell.
Video Intercom 9 Series Indoor Station Configuration Guide Before You Start Tap Settings → → Shortcut Settings to enable Zone Alarm Locally. Steps Note Arming status page and zone settings page are hidden by default. You should enable alarm function first. 1. Tap Settings → → Scene Settings to enter the arming mode settings page. 2. Tap Stay Mode, Away Mode, Sleeping Mode, or Custom to enter the page. Figure 2-8 Arming Mode Settings 3. Arm the selected zone.
Video Intercom 9 Series Indoor Station Configuration Guide Steps 1. Tap Settings → → Password to enter the password settings page. Figure 2-9 Password Settings 2. Tap Unlock Password, Arm/Disarm, or Duress Code to pop up the password settings dialog box. Unlock Password Enter the unlock password and room No. on the door station to open the door. Arm/Disarm Create an arm/disarm password before configuring alarm parameters. Arm or disarm the zone for the indoor station by entering the arm/disarm password.
Video Intercom 9 Series Indoor Station Configuration Guide 4. Create a new password and confirm it. 5. Tap OK to save the settings. Note Indoor Extension only supports admin password and arm/disarm password. 6. Enable Switch Scene without Password and enter the arm/disarm password. There is no need to enter the password during scene mode switching. 2.4 Synchronize Time Steps 1. Tap Settings → → Time to enter the time settings page. 2. Synchronize the system time.
Video Intercom 9 Series Indoor Station Configuration Guide You can set the ringtone, ring duration, call forwarding time, volume of microphone and loudspeaker and enable/disable touch sound on call settings page. Steps 1. Tap Settings → to enter the call settings page. Figure 2-11 Call Settings 2. Set corresponding parameters. Ringtone There are 3 ringtones by default, and you can custom and import at most 4 ringtones via Batch Configuration Tool or iVMS-4200 Client Software.
Video Intercom 9 Series Indoor Station Configuration Guide Steps 1. Tap Settings → page. → Configuration → to enter the restore default settings Figure 2-12 Restore Default Settings 2. Tap Restore Default Settings to restore the default settings and reboot the system. 3. Tap Restore All to restore all parameters and reboot the system. 2.7 System Settings Language Tap Settings → → Language to change the system language. Note The indoor station supports 5 languages.
Video Intercom 9 Series Indoor Station Configuration Guide You can view the Version, System Version, Model, Serial No., Playing Library Version, Two-Way Audio Library Version and OSS Statement. Reboot Device Tap Settings → to enter the settings page. Reboot Automatically Enable Reboot Automatically and configure the Reboot Schedule according to your needs. Reboot Manually Tap Reboot to reboot the system. Upgrade Device Tap Settings → Configuration Settings → maintenance page.
Video Intercom 9 Series Indoor Station Configuration Guide Steps 1. Tap Settings → Cloud Service to enter the settings page. 2. Enable Cloud Service. 3. Edit LBS server and Verification Code. Note Verification code is used to add the device to mobile client. 4. Optional: Scan QR code on the screen to add the device to the mobile client. 2.9 Shortcut Settings Tap Settings → → Shortcut Settings to enter the settings page.
Video Intercom 9 Series Indoor Station Configuration Guide 3 Remote Operation via the client software The Video Intercom module provides remote control and configuration on video intercom products via the iVMS-4200 client software. 3.1 Activate Device Remotely You can only configure and operate the indoor station after creating a password for the device activation. Before You Start Default parameters of indoor station are as follows: • Default IP Address: 192.0.0.64. • Default Port No.: 8000.
Video Intercom 9 Series Indoor Station Configuration Guide Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 3.2.1 Add Video Intercom Devices Steps Note • You can add at most 512 indoor stations and master stations in total to the client, and add at most 16 door stations to the client.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-1 Add the Device 4. Optional: Click Online Device, the active online devices in the same local subnet with the client software will be displayed on the Online Device area. Note To add online devices to the software, you are required to change the device IP address to the same subnet with your computer first. 1) You can click Refresh Every 60s to refresh the information of the online devices. 2) Select the devices to be added from the list.
Video Intercom 9 Series Indoor Station Configuration Guide Edit a name for the device as you want. Address Input the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port Input the device port No. The default value is 8000. User Name Input the device user name. By default, the user name is admin. Password Input the device password. By default, the password is 12345. 6. Optional: You can check the checkbox Export to Group to create a group by the device name.
Video Intercom 9 Series Indoor Station Configuration Guide 3.3 System Configuration You can configure the video intercom parameters accordingly. Steps 1. Click Maintenance and Management → System Configuration → Acs and videoIntercom to enter the system configuration page. 2. Enter the required information. Ringtone Click ... and select the audio file from the local path for the ringtone of for a testing of the audio file. indoor station. Optionally, you can click Max.
Video Intercom 9 Series Indoor Station Configuration Guide Device Information Click Device Information to enter device basic information page. You can view basic information (the device type, and serial No.), and version information of the device. Figure 3-2 Device Information General Click General to enter device general parameters settings page. You can view and edit the device name and device ID. Figure 3-3 General Time Click Time to enter the device time settings page.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-4 Synchronize Time Select Time Zone or Enable NTP. Click Save to save the time settings. • Time Zone • Select a time zone from the drop-down list menu. • Click Synchronization. • NTP • Check the checkbox of Enable NTP to enable NTP. • Enter the server address, NTP port, and synchronization interval. • DST • Check the checkbox of Enable DST to enable DST. • Enter the start time and end time of DST, and set the DST bias.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-5 System Maintenance • Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the system. • Click Restore Default Settings to restore the default parameters. • Click Restore All to restore all parameters of device and reset the device to inactive status. Note • Click Restore Default Settings, all default settings, excluding network parameters, will be restored.
Video Intercom 9 Series Indoor Station Configuration Guide • Click ... to select the upgrade file and click Upgrade to remote upgrade the device. The process of remote upgrade will be displayed in the process bar. • Select a language, and click Save to change the device system language. Note • The device supports 11 languages: English, Russian, German, Italian, French, Portuguese, Spanish, Turkish, Arabic, Polish, and Vietnamese. • Rebooting the device is required after you change the system language.
Video Intercom 9 Series Indoor Station Configuration Guide RS-485 Click RS485 to enter the RS-485 settings page. You can view and edit the RS-485 parameters of the device. Figure 3-7 RS-485 Settings Note For indoor station and master station, there are 3 choices for the working mode: transparent channel, disable, and custom. 3.4.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-8 Time Parameters 2. Configure the maximum ring duration, maximum live view time, and call forwarding time. 3. Click Save. Note • Maximum ring duration is the maximum duration of indoor station when it is called without being received. The range of maximum ring duration varies from 30s to 60s. • Maximum live view time is the maximum time of playing live view of the indoor station.
Video Intercom 9 Series Indoor Station Configuration Guide For indoor station, you can change the admin password, arm/disarm password, unlock password and duress code. For indoor extension, only admin password and arm/disarm password need to be configured. Zone Alarm Steps 1. Click Zone Alarm to enter the zone settings page. Figure 3-10 Zone Alarm 2. Select a zone type from the drop-down list menu. 3. Select an alarm mode from the drop-down list menu. 4. Set the zone status: NO or NC. 5.
Video Intercom 9 Series Indoor Station Configuration Guide Under disarming mode, it will not receive alarm message when the detector is triggered. • When the zone type is set to be 24H Alarm, the indoor station will receive alarm message when the detector is triggered no matter it is under arming mode or disarming mode. • When the zone type is set to be Delay Alarm, only under arming mode, the indoor station will receive alarm message when the detector is triggered.
Video Intercom 9 Series Indoor Station Configuration Guide Note Indoor extension does not support this function. Export and Import Added Device Information Steps 1. Click Export to export the added device information file. 2. Edit parameters of added devices in batch in the exported file. 3. Click Import to pop up importing box, and open the edited added device information file. Figure 3-12 Import Added Device Information Volume Input and Output Steps 1.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-13 Volume Input and Output 2. Slide the slider to adjust the volume input, volume output and talk volume. 3. Click Save to enable the settings. Ring Import Steps 1. Click Ring Import to enter the ring configuration page. Figure 3-14 Ring Import 2. Click + to add the ring, and click x to delete the imported ring. Note • The ring to be imported should be in the wav format, and the size of the ring cannot be larger than 300k.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-15 Deploy Info Incoming Call Linkage Steps 1. Click Incoming Call Linkage to enter configuration the page. Figure 3-16 Incoming Call Linkage 2. Enable and select triggers. When the calling incoming, the alarm you linked will be triggered. Relay Click Relay. Select a relay and click time. Click OK to save the settings.
Video Intercom 9 Series Indoor Station Configuration Guide The Third-Party APP Settings View the App information in the list and add/delete the App remotely. Steps 1. Click App Information List to enter the settings page. 2. Click Add, enter the URL to get the package. 3. Optional: Select the App, click Delete to uninstall the App. SIP No. Settings You can view and edit the SIP informations in SIP No. Settings page. Steps 1. Click SIP No. Settings to enter the settings page. 2.
Video Intercom 9 Series Indoor Station Configuration Guide Local Network Configuration Steps 1. Click Local Network Configuration to enter local network configuration page. Figure 3-18 Local Network Configuration 2. Enter the local IP address, subnet mask, gateway address, and port No. 3. Click Save to enable the settings. Note • The default port No. is 8000. • After editing the local network parameters of device, you should add the devices to the device list again. SIP Settings Steps 1.
Video Intercom 9 Series Indoor Station Configuration Guide Figure 3-19 SIP Settings 2. Set the parameters according to your needs. 3. Click Save to enable the settings. DNS Settings The indoor station supports 2 DNS address. Click Advanced Settings to enter DNS address settings page. Edit the IP address and click Save.
Video Intercom 9 Series Indoor Station Configuration Guide Configure Hik-Connect server parameters before viewing videos via mobile client. Before You Start Make sure the indoor station connects to the network. Steps 1. Click Hik-Connect to enter configuration page. 2. Enable Enable Hik-Connect Access. 3. Enable Custom and edit Service Address 4. Enter the Verification Code. 5. Click Save.
Video Intercom 9 Series Indoor Station Configuration Guide 5. Select the main door station type from the drop-down list. 6. Click Save to enable the settings. Note • After adding master station IP Address, the linkage between indoor station and master station can be realized. • After adding the door station IP Address, the video intercom between indoor stations of same building can be realized.
Video Intercom 9 Series Indoor Station Configuration Guide The page is divided into two parts: Organization Management and Person Management. Organization Management You can add, edit, or delete the organization as desired. Person Management After adding the organization, you can add the person to the organization and issue card to persons for further management. 3.5.1 Organization Management In the main page of the Client Software, click Application to enter the configuration page.
Video Intercom 9 Series Indoor Station Configuration Guide Note • The lower-level organizations will be deleted as well if you delete an organization. • Make sure there is no person added under the organization, or the organization cannot be deleted. 3.5.2 Person Management After adding the organization, you can add person to the organization and manage the added person such as issuing cards in batch, importing and exporting person's information in batch, etc.
Video Intercom 9 Series Indoor Station Configuration Guide Click Remote Collection Take the person's photo with the collection device. 3. Issue the card for the person. 1) Click Credential → Card . 2) Click + to pop up the Add Card dialog. 3) Select Normal Card as Card Type. 4) Enter the Card No. 5) Click Read and the card(s) will be issued to the person. 4. Add fingerprints to the person. 1) Click Credential → Fingerprint . 2) Click + to pop up the Add Fingerprint dialog. 3) Select Collection Mode.
Video Intercom 9 Series Indoor Station Configuration Guide 4) Click ... to select the Excel file with person information. 5) Click OK to start importing. Get Person Information from Device If the added device has been configured with person information (including person details, fingerprint, issued card information), you can get the person information from the device and import to the client for further operation.
Video Intercom 9 Series Indoor Station Configuration Guide Change Person to Other Organization You can move the person to another organization if needed. Steps 1. Select the person in the list and click Change Organization. 2. Select the organization to move the person to. 3. Click OK to save the settings.
Video Intercom 9 Series Indoor Station Configuration Guide A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD19193B
