Video Intercom Villa Door Station User Manual
Video Intercom Villa Door Station User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom Villa Door Station User Manual CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Video Intercom Villa Door Station User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom Villa Door Station User Manual Safety Instruction Warning • The working temperature of the device is from -10 ºC to 55 ºC. • All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. • Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.
Video Intercom Villa Door Station User Manual • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. • Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. • Please keep all wrappers after unpack them for future use.
Video Intercom Villa Door Station User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Villa Door Station User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Video Intercom Villa Door Station User Manual Contents 1 Appearance ................................................................................................ 1 2 Terminal and Wiring Description ................................................................ 3 2.1 Terminal Description ......................................................................................... 3 2.2 Wiring Description ............................................................................................ 3 2.2.
Video Intercom Villa Door Station User Manual 5.5.1 Local Parameters Settings ....................................................................... 15 5.5.2 System Settings ....................................................................................... 16 5.5.3 Network Settings .................................................................................... 19 5.5.4 Video & Audio Settings ........................................................................... 23 5.5.5 Image Settings ......
Video Intercom Villa Door Station User Manual 6.4.6 Issue Card in Batch ................................................................................. 44 6.4.7 Permission Settings ................................................................................. 46 6.5 Video Intercom Settings .................................................................................. 47 6.5.1 Receive Call from Door Station ............................................................... 47 6.5.2 Release Notice .....
Video Intercom Villa Door Station User Manual 1 Appearance Front Panel and Rear Panel Figure 1-1 Front Panel and Rear Panel Table 1-1 Description No.
Video Intercom Villa Door Station User Manual No. Description 6 Loudspeaker 7 Terminals 8 Debugging Port 9 TAMPER 10 Set Screw Bottom Panel Figure 1-2 Bottom Panel Table 1-2 Description No.
Video Intercom Villa Door Station User Manual 2 Terminal and Wiring Description 2.1 Terminal Description Figure 2-1 Terminal Description 2.2 Wiring Description 2.2.
Video Intercom Villa Door Station User Manual Note Terminal NC/COM is set as default for accessing magnetic lock/electric bolt; terminal NO/COM is set as default for accessing electric strike. 2.2.2 Door Contact Wiring Figure 2-3 Door Contact Wiring 2.2.
Video Intercom Villa Door Station User Manual 2.2.
Video Intercom Villa Door Station User Manual 3 Installation Note • Make sure the device in the package is in good condition and all the assembly parts are included. • Make sure your power supply matches your door station. • Make sure all the related equipment is power-off during the installation. • Check the product specification for the installation environment. 3.1 Accessory Introduction Figure 3-1 Accessory Introduction Note The dimension of the mounting plate is 102.58 mm × 39.24 mm × 6.2 mm.
Video Intercom Villa Door Station User Manual 3.2 Surface Mounting without Protective Shield Before You Start • Tools that you need to prepare for installation: Drill (ø2.846) and gradienter. • Purchase the protective shield before installation. Steps 1. Stick the mounting template on the wall. Drill screw holes according to the mounting template. Remove the template from the wall. Figure 3-2 Mounting Template 2.
Video Intercom Villa Door Station User Manual Figure 3-3 Surface Mounting without Protective Shield 3.3 Surface Mounting with Protective Shield Before You Start • Tools that you need to prepare for installation: Drill (ø2.846) and gradienter. • Purchase the protective shield before installation. Steps 1. Stick the mounting template on the wall. Drill screw holes according to the mounting template. Remove the template from the wall.
Video Intercom Villa Door Station User Manual Figure 3-4 Mounting Template 2. Align the protective shield with the mounting template. 3. Secure the mounting plate and protective shield on the wall with 4 supplied screws according to the screw holes. 4. Install the villa door station to the mounting plate. Fix the device on the mounting plate with the set screw.
Video Intercom Villa Door Station User Manual Figure 3-5 Flush Mounting with Protective Shield 10
Video Intercom Villa Door Station User Manual 4 Activation 4.1 Activate Device via Web You are required to activate the device first by setting a strong password for it before you can use the device. Default parameters of the door station are as follows: • Default IP Address: 192.0.0.65. • Default Port No.: 8000. • Default User Name: admin Steps 1. Power on the device, and connect the device to the network. 2.
Video Intercom Villa Door Station User Manual 3. Select an inactivated device and click Activate. 4. Create a password, and confirm the password. Note We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Video Intercom Villa Door Station User Manual 5 Remote Configuration via Web 5.1 Live View In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page. Enter the user name and password and click Login to enter the Live View page. Or you can click Live View to enter the page. Figure 5-1 Live View • You can start/stop live view, capture, record, audio on/off, two-way audio, etc. • The stream type can be set as main stream or sub stream.
Video Intercom Villa Door Station User Manual Note User management function may vary with different models. Please refer to the actual product. 5.3 Number Settings Link the room No. and SIP numbers. Click Number Settings to enter the page. Click Add, set the Room No. and SIP numbers in the pop-up dialog box. 5.4 Device Management You can manage the linked device on the page. Click Device List to enter the settings page. Add Device • Click Add to add the indoor station or sub door station.
Video Intercom Villa Door Station User Manual Note Run the browser, click Mode. → Internet Options → Security to disable the Protected 5.5.1 Local Parameters Settings You can configure the parameters of the live view, record files and captured pictures. The record files and captured pictures are the ones you record and capture by using the web browser. You can also set and view the saving paths of the captured pictures and recorded videos on the PC that running the web browser.
Video Intercom Villa Door Station User Manual Set the saving path of the manually captured pictures in live view mode. Note You can click Browse to change the directory for saving the clips and pictures, and click Open to open the set folder of clips and picture saving. Click Save to enable the settings. 5.5.2 System Settings Follow the instructions below to configure the system settings, include System Settings, Maintenance, Security, and User Management, etc. Click System to enter the settings page.
Video Intercom Villa Door Station User Manual Figure 5-2 Maintenance • Reboot: Click Reboot to reboot the device. • Restore Click Restore to reset all the parameters, except the IP parameters and user information, to the default settings. Default Click Default to restore all parameters to default settings. • Export parameters: 1. Select Device Parameters, and click Export to pop up the dialog box. 2. Set and confirm the encryption password. 3. Click OK to export parameters. • Import Config. File: 1.
Video Intercom Villa Door Station User Manual Security Service Click Security → Security Service to enter the settings page. On the page, you can enable SSH according to your actual needs. Click Save to enable the settings. User Management Click User Management to enter the settings page. Administrator can edit the permission for the users.
Video Intercom Villa Door Station User Manual 5.5.3 Network Settings TCP/IP Settings TCP/IP settings must be properly configured before you operate the device over network. The device supports IPv4. Steps 1. Click Network → Basic Settings → TCP/IP to enter the settings page. Figure 5-4 TCP/IP Settings 2. Configure the network parameters. - Check DHCP, the device will get the parameters automatically. - Set the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway manually. 3.
Video Intercom Villa Door Station User Manual 4. Click Save to enable the settings. Port Settings Steps 1. Click Network → Basic Settings → Port to enter the settings page. Figure 5-5 Port Settings 2. Set the ports of the device. HTTP Port The default port number is 80, and it can be changed to any port No. which is not occupied. HTTPS Port The default port number is 443, and it can be changed to any port No. which is not occupied. RTSP Port The default port number is 554.
Video Intercom Villa Door Station User Manual 3. Click Add, and set corresponding parameters. and Password of the Wi-Fi. 1) Enter the SSID. 2) Select Working Mode. 3) Select Encryption Type. 4) Click OK. 5) Optional: Click Refresh to get the present information. 4. Click Network Settings, and set corresponding parameters. 5. Select Security Mode. 6. Click Connect. SIP Setting Steps 1. Click Network → Basic Settings → SIP to enter the settings page. Figure 5-6 SIP Settings 2. Check Enable VOIP Gateway. 3.
Video Intercom Villa Door Station User Manual Steps 1. Click Network → Advanced → FTP to enter the settings page. Figure 5-7 FTP Settings 2. Check Enable FTP. 3. Select Server Type. 4. Input the Server IP Address and Port. 5. Configure the FTP Settings, and the user name and password are required for the server login. 6. Set the Directory Structure, Parent Directory and Child Directory.
Video Intercom Villa Door Station User Manual 7. Set the picture naming rules. 8. Click Save to enable the settings. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Click Network → Advanced Settings → Platform Access to enter the settings page. 2. Check the checkbox of Enable to enable the function. 3. Select the Platform Access Mode. Note Hik-Connect is an application for mobile devices.
Video Intercom Villa Door Station User Manual Figure 5-8 Video Parameters 2. Select the Stream Type. 3. Configure the video parameters. Stream Type Select the stream type to main stream or sub stream. Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. Resolution Select the resolution of the video output. Bitrate Type Select the bitrate type to constant or variable.
Video Intercom Villa Door Station User Manual Max. Bitrate Set the max. bitrate from 32 to 16384 Kbps. The higher value corresponds to the higher video quality, but the better bandwidth is required. Video Encoding The device supports H.264. I Frame Interval Set I Frame Interval from 1 to 400. 4. Click Save to save the settings. Audio Parameters Steps 1. Click Video/Audio → Audio to enter the settings page. Figure 5-9 Audio Settings 2. Configure the stream type and the audio encoding type.
Video Intercom Villa Door Station User Manual 5.5.5 Image Settings Display Settings Configure the image adjustment, backlight settings and other parameters in display settings. Steps 1. Click Image → Display Settings to enter the display settings page. Figure 5-10 Display Settings 2. Select the Format. 3. Set the display parameters. WDR Wide Dynamic Range can be used when there is a high contrast of the bright area and the dark area of the scene.
Video Intercom Villa Door Station User Manual 4. Set the Day/Night Mode. - Figure 5-11 Day/Night Mode Set Day Mode or Night Mode manually. Set the mode as Auto and edit the sensitivity according to your needs. Set the mode as Scheduled-Switch. Set the start time and end time. Note Daytime is from configured start time to configured time. The rest of the time is set as night by default. 5. Set the backlight parameters.
Video Intercom Villa Door Station User Manual Figure 5-12 Backlight 1) Check the checkbox to enable BLC. 2) Select BLC Area. 6. Click Save to enable the settings. OSD Settings You can customize the camera name, time/date format, display mode, and OSD size displayed on the live view. Steps 1. Click Image → OSD Settings to enter the settings page. 2. Check the corresponding checkbox to select the display of camera name, date or week if required. 3. Edit the Camera Name. 4.
Video Intercom Villa Door Station User Manual Steps 1. Click Image. 2. Enable target cropping. 3. Click " " to crop photo. 4. Click " " to crop video. 5. Select Cropping Resolution. 6. Click Save. 5.5.6 Event Settings Motion Detection Motion detection detects the moving objects in the configured surveillance area, and a series of actions can be taken when the alarm is triggered. Steps 1. Click Event → Motion to enter the settings page.
Video Intercom Villa Door Station User Manual Figure 5-13 Motion Detection 2. Check Enable Motion Detection to enable the function. 3. Click Draw Area. Click and drag the mouse on the live video to draw a motion detection area. Click Stop Drawing to finish drawing one area. Click Save to save the settings. Clear Area Click Clear All to clear all of the areas. Adjust Sensitivity Move the slider to set the sensitivity of the detection. 4. Click Arming Schedule to edit the arming schedule. 5.
Video Intercom Villa Door Station User Manual Send an exception or alarm signal to the remote management software when an event occurs. 7. Click Save to enable the settings. Event Linkage Steps 1. Click Event → Basic Event → Event Linkage to enter the settings page. Figure 5-14 Event Linkage 2. Select the Major Type as Device Event or Door Event.
Video Intercom Villa Door Station User Manual 3. Select the type of the Normal Linkage for the event. 4. Click Save to enable the settings. 5.5.7 Schedule Settings You can create call schedule, or else the device will call indoor station all day by default. Steps 1. Click Schedule → Video Intercom . 2. Click the next row below Enable Indoor Station All Day by Default. 3. Enter Schedule Name. 4. Select Call Type. 5. Set Weekly Schedule. 1) Click Weekly Schedule.
Video Intercom Villa Door Station User Manual Device ID Configuration Steps 1. Click Device ID Settings to enter the page. Figure 5-15 Device ID Settings 2. Select the device type from the drop-down list, and set the corresponding information. 3. Click Save to enable the device number configuration. Note • For main door station (D series or V series), the serial No. is 0. • For sub door station (D series or V series), the serial No. cannot be 0. Serial No. ranges from 1 to 99.
Video Intercom Villa Door Station User Manual Figure 5-16 Linked Network Settings 2. Set Register Number and Registration Password. 3. Set Master Station IP and VideoIntercom Server IP. 4. Enable Protocol 1.0. 5. Click Save to enable the settings. Time Parameters Go to Intercom → Time Parameters to enter the page. Configure Max. Call Duration, Max. Message Duration, Max. Ring Duration, and click Save. Ring-Back Tone Settings Click Intercom → Ringbacktone Settings to enter the settings page.
Video Intercom Villa Door Station User Manual Note If you check Call Indoor Station, you should enter the call indoor station No. 3. Click Save. Input and Output Go to Intercom → I/O Settings to enter the settings page. Figure 5-17 IO Input and Output Select I/O Input No., Input, I/O Output No. and Output. Click Save to enable the settings. 5.5.9 Access Control Settings Door Parameters Steps 1. Click Access Control → Door Parameters to enter the settings page.
Video Intercom Villa Door Station User Manual Figure 5-18 Door Parameters 2. Select the door and edit the door name. 3. Set door contact status. 4. Set lock action time. 5. Click Save to enable the settings. Card Security Go to Access Control → Card Security to enter the settings page. Slide to enable card encryption parameters and CPU card reading content. Click Save to enable the settings. Elevator Control Before You Start • Make sure your door station is in the mode of main door station.
Video Intercom Villa Door Station User Manual Figure 5-19 Elevator Control 2. Check to enable elevator control function. 3. Select an Elevator No., and select an elevator controller type for the elevator. 4. Set the Negative Floor. 5. Select the Interface Type as RS-485 or Network Interface. And enable the elevator control. - If you select RS-485, make sure you have connected the door station to the elevator controller with RS-485 wire.
Video Intercom Villa Door Station User Manual 6 Configuration via Client Software 6.1 Device Management Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 6.1.1 Add Online Device Before You Start Make sure the device to be added is in the same subnet with your computer. Otherwise, please edit network parameters first.
Video Intercom Villa Door Station User Manual Figure 6-1 Add to the Client 6.1.2 Add Device by IP Address Steps 1. Click +Add to pop up the adding devices dialog box. 2. Select IP/Domain as Adding Mode. 3. Enter corresponding information. 4. Click Add. 6.1.
Video Intercom Villa Door Station User Manual You can add many devices at once whose IP addresses are among the IP segment. Steps 1. Click +Add to pop up the dialog box. 2. Select IP Segment as Adding Mode. 3. Enter corresponding information, and click Add. 6.2 Live View via Door Station Steps 1. On the main page of the client software, click Main View to enter the Live View page. 2. In the left list of the window, double-click the device IP or click the play icon to live view. 3.
Video Intercom Villa Door Station User Manual Note Up to 10 levels of organizations can be created. 6.3.2 Modify and Delete Organization You can select the added organization and click to modify its name. You can select an organization, and click X button to delete it. Note • The lower-level organizations will be deleted as well if you delete an organization. • Make sure there is no person added under the organization, or the organization cannot be deleted. 6.
Video Intercom Villa Door Station User Manual 1) Enter basic information: name, gender, tel, birthday details, effective period and email address. Note The length of person name should be less than 15 characters. 2) Click Add face to upload the photo. Note The picture should be in *.jpg format. Click Upload Select the person picture from the local PC to upload it to the client. Click Take Phone Take the person's photo with the PC camera.
Video Intercom Villa Door Station User Manual 6.4.2 Modify and Delete Person Select the person and click Edit to open the editing person dialog. To delete the person, select a person and click Delete to delete it. Note If a card is issued to the current person, the linkage will be invalid after the person is deleted. 6.4.3 Change Person to Other Organization You can move the person to another organization if needed. Steps 1. Select the person in the list and click Change Organization. 2.
Video Intercom Villa Door Station User Manual 5) Click OK to start importing. 6.4.5 Get Person Information from Device If the added device has been configured with person information (including person details, fingerprint, issued card information), you can get the person information from the device and import to the client for further operation. Steps Note This function is only supported by the device the connection mothod of which is TCP/IP when adding the device. 1.
Video Intercom Villa Door Station User Manual Figure 6-2 Issue Card in Batch 2. Click Settings.
Video Intercom Villa Door Station User Manual Figure 6-3 Card Settings 3. Select Card Type and Card No. Type. 4. Click OK to save the settings. Result After issuing the card to the person, the person and card information will display in the Person(s) with Card Issued list. 6.4.7 Permission Settings Add Permissions Steps 1. On the main page, click page. AccessControlInfo → Access Group to enter the 2. Click +Add to pop up the adding dialog box. 3. Configure the parameters.
Video Intercom Villa Door Station User Manual 2) Select the Template of the schedule. 3) Check the person to Selected according to your needs. 4) Check the device to Selected according to your needs. 4. Click Save. 5. Check the permission and click Apply All to Device. The status of the permission displays as Applied. 6. Optional: Click Applying Status to check the details. Modify/Delete Permissions On the page of the permission settings, click permission.
Video Intercom Villa Door Station User Manual Adjust the Volume of Loudspeaker Click Hang Up Click Hang Up to hang up. Adjust the Volume of Microphone Click Unlock Remotely For door station, you can click door remotely. to adjust the volume of loudspeaker. to adjust the volume of microphone. to open the Note • One video intercom device can only connect with one client software. • The maximum ring duration can be set from 15s to 60s via the Remote Configuration of the video intercom device.
Video Intercom Villa Door Station User Manual Note • Up to 63 characters are allowed in the Subject field. • Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB. • Up to 1023 characters are allowed in the Information field. 6.5.3 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Call Log to enter the page. Figure 6-4 Search Call Logs 2.
Video Intercom Villa Door Station User Manual Start Time/End Time Click the time icon to specify the start time and end time of a time period to search the logs. Reset the Settings Click Reset to reset all the configured search conditions. 3. Click Search and all the matched call logs will display on this page. 4. Optional: Check the detailed information of searched call logs, such as call status, ring/speaking duration, device name, resident organization, etc. 5.
Video Intercom Villa Door Station User Manual Note • While device has been added to the client software, the device armed by default. • When the device is armed, the alarm logs upload to the client software automatically. • Click Alarm Application → Event Search to search the alarm logs. 3. Optional: Click Arm All or Disarm All to arm or disarm all the device.
Video Intercom Villa Door Station User Manual A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD20205B
