User Manual

11
Specificaon
8
5
7
Funcons
Operaon Cauon and Device Maintenance
- All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regulaons and other related
regulaons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment
installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment
installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operaon temperature), cold, dusty or
damp locaons, and do not expose it to high electromagnec radiaon.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfuncon however), and
affecng the endurance of sensor at the same me.
- Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used baeries according to the instrucons provided by the baery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situaon.
You can add two external inputs (each input can be set as NO\NC\TAMPER\Pulse) via the AX PRO client.
While Any of the two inputs generates an alarm event, the detector reports the alarm to the AX PRO. The LED keeps blue for 2 s.
4
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Set Up with App
6
You can view the device status including temperature, signal intensity, baery level, lid, external input, etc.,on the device page.
Tap the buon to enter the sengs page.
Formang
1. Remove the baery.
2. Hold the TAMPER buon and power the detector on at the same me.
The red LED flashes 3 me when the formang is completed.
Disallowed field adjustable sengs: None
Model DS-PDBG8-EG2-WB/WE
Detecon Performance
Detecon Method Acousc Sensor
Detecon Range 8m
Detecon Angle 120°
Sensivity 2m,4m,6m,8m
Glass Type
Float,Plate,Tampered,Wired,Laminated
Leaded,Double Glazing
Glass Thickness 2.4mm to 6.4mm
Glass Size 0.3m x 0.3m to 3m x 3m
Feature
Digital Processing Support
Tamper Protecon Front,Rear
Environment Temperature Indicator Support
Signal Strength Indicator Support
Interface
Alarm Input Normally Closed,Normally Open,Impulse Count
Power Switch Power Up Enrolling
LED Indicator Blue(Alarm)
Transmission
Transmission Technology Tri-X Wireless
Transmission Method Two-Way RF Wireless
Transmission Frequency 433MHz/868MHz
Transmission Security AES-128 Encrypon
Transmission Range(Free Space) 1Km(433MHz)/1.6Km(868MHz)
Frequency Hopping Support
Enrolling Method Power up,Remote ID,QR Code
Electrical Characteriscs
Power Supply Baery Powered
Baery Type CR123A × 2
Typical Voltage 3V
Standard Baery Life 5 Years
General
Operaon Temperature -10 °C to 55 °C (14 °F to 131 °F)
Storage Temperature -20 °C to 60 °C (-4 °F to 140 °F)
Operaon Humidity 10% to 90%
Dimension(WxHxD) 38.8mm × 107.0mm × 24.5mm
Weight 83g
Mounng Method Wall,Ceiling
Applicaon Scenario Indoor