DS-K1T690 Series Face Recognition Terminal User Manual
DS-K1T690 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T690 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T690 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T690 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T690 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T690 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T690 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T690 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless Description DS-K1T690MF 13.56MHz + Bluetooth DS-K1T690MF-X 13.56MHz + Bluetooth DS-K1T690M-T 13.56MHz + Bluetooth DS-K1T690M-E1 13.56MHz + Bluetooth DS-K1T690MW 13.56 MHz + 2.4 G Wi-Fi + Bluetooth Use only power supplies listed in the user instructions: Model Manufacturer Standard C2000IC12.0-24P-DE MOSO Power Supply Technology Co., Ltd. CEE C2000IC12.
DS-K1T690 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T690 Series Face Recognition Terminal User Manual 6.3 Set Administrator ................................................................................................................. 41 Chapter 7 Basic Operation ........................................................................................................ 45 7.1 Login .................................................................................................................................... 45 7.1.1 Login by Administrator .........
DS-K1T690 Series Face Recognition Terminal User Manual 7.7 Set Biometric Parameters .................................................................................................... 65 7.8 Temperature Measurement Settings ................................................................................... 67 7.9 Set Access Control Parameters ............................................................................................ 69 7.10 Preference Settings .............................................
DS-K1T690 Series Face Recognition Terminal User Manual 8.6.11 Online Users .............................................................................................................. 86 8.6.12 View Device Arming/Disarming Information ............................................................ 87 8.6.13 Network Settings ....................................................................................................... 87 8.6.14 Set Video and Audio Parameters ..........................................
DS-K1T690 Series Face Recognition Terminal User Manual 9.4.2 Import and Export Person Identify Information ........................................................ 131 9.4.3 Get Person Information from Access Control Device ................................................ 134 9.4.4 Issue Cards to Persons in Batch ................................................................................. 134 9.4.5 Report Card Loss ........................................................................................
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 15.6-inch LCD touch screen 2 MP wide-angle dual-lens Face recognition distance: 0.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No.
DS-K1T690 Series Face Recognition Terminal User Manual No.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● ● Note Interfaces of the device vary by model.The figures are for reference only. The soundbox interface does not support external headphones. Only devices that support the POE function have POE network ports. Other devices feature network ports.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-1 Install Gang Box 2. After aligning the mounting plate screw holes with the gang box holes, secure the mounting plate on the wall with four supplied screws (SC-KA4×22).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-2 Install Mounting Plate 3. Route the cable through the cable hole, wire the cables and insert the cables in the gang box. Note Apply silicone sealant among the cable wiring area to keep the raindrop from entering.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-3 Apply Silicone Sealant 4. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-M4×8-SUS-NL).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-4 Secure Device 5. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.3 Flush Mounting (Type II) Steps 1. Cave an installation hole on the wall. Pull the cable out from the wall. Note ● The suggested dimension of the installation hole is 324 mm (W) × 337 mm (H) × 47.5 mm (D). ● The mounting methods is optional. You should pay for the gang box. 2.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-5 Install Gang Box 3. Install the mounting plate on the gang box with the four supplied screws (SC-K1M4×6).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-6 Install Mounting Plate 4. Route the cable through the cable hole, wire the cables and insert the cables in the gang box. Note Apply silicone sealant among the cable wiring area to keep the raindrop from entering.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-7 Apply Silicone Sealant 5. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-M4×8-SUS-NL).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-8 Secure Device 6. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.4 Surface Mounting Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-9 Mounting Template 2. Drill holes on the wall or other surface according to the Hole 1 on the mounting template. 3. Remove the cable hole on the mounting plate with tools. 4. Align the holes to the mounting plate and secure the mounting plate on the wall with the 4 supplied screws (K1A×24).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-10 Install Mounting Plate 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding peripherals cables. Note If the device is installed outdoor, you should apply silicone sealant to the wiring exit to avoid water from entering.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-11 Apply Silicone Sealant 6. Align the device with the mounting plate and hang the device on the mounting plate.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-12 Hang Device 7. Use 1 supplied screw (SC-M4×8-SUS-NL) to secure the device and the mounting plate.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-13 Secure Device 8. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.5 Base Mounting Steps Note You can refer to the following figure for base mounting bracket size.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-14 Base Mounting Bracket 1. Remove the back cover plate, route the cables through the cable hole, and connect them to the corresponding external devices' cables. 2. Install the back cover plate back, and install the device on the bracket with 4 supplied screws (SC-KM3×6-T10-SUS).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-15 Remove Back Cover Plate Note The base mounting bracket is optional accessory. You should buy it for yourself. 3. Put the mounted device on the desk or other surface. 4. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.6 Bracket Mounting Steps 1. Install the mounting plate on the bracket with 4 supplied screws (SC-K1M4×6).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-16 Install Mounting Template Note The bracket is optional accessory. You should buy it for yourself. 2. Remove the back cover plate, route the cables through the cable hole, and connect them to the corresponding external devices' cables. 3. Install the back cover plate back, and install the device on the bracket with 1 supplied screw (SCM4×8_SUS-NL).
DS-K1T690 Series Face Recognition Terminal User Manual Figure 3-17 Install Device 4. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, the exit button, the alarm output/input devices, the Wiegand card reader, the access controller, and the power supply. You can wire the peripherals according to the descriptions below.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-1 Terminal Diagram The descriptions of the terminals are as follows: 24
DS-K1T690 Series Face Recognition Terminal User Manual Table 4-1 Terminal Descriptions Group Group A No.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-2 Device Wiring ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly. 4.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-3 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module 4.4.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-4 Wire Device Figure 4-5 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-6 Wiring Device Figure 4-7 Wiring Secure Door Control Unit 4.4.
DS-K1T690 Series Face Recognition Terminal User Manual Scenario: Installed in Entrance/Exit with Fire Linkage ● ● Note The Uninterpretable Power Supply (UPS) is required. The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 4-9 Wiring Diagram 31
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked.
DS-K1T690 Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● ● ● ● After activation, you should select a language according to your actual needs.
DS-K1T690 Series Face Recognition Terminal User Manual The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details. Steps 1. Run the SADP software and search the online devices. 2. Find and select your device in online device list. 3. Input new password (admin password) and confirm the password.
DS-K1T690 Series Face Recognition Terminal User Manual 5.4 Activate Device via iVMS-4200 Client Software For some devices, you are required to create the password to activate them before they can be added to the iVMS-4200 software and work properly. Steps Note This function should be supported by the device. 1. Enter the Device Management page. 2. Click on the right of Device Management and select Device. 3. Click Online Device to show the online device area.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 6-1 Welcome Page 2. Tap OK to save.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 6-2 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device.
DS-K1T690 Series Face Recognition Terminal User Manual Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function. Upload Pic. After Linked Capture (Upload Picture After Linked Capture) Upload the pictures captured by linked camera to the platform automatically. Save Pic. After Linked Capture (Save Pictures After Linked Capture) If you enable this function, you can save the picture captured by linked camera to the device.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 6-3 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added.
DS-K1T690 Series Face Recognition Terminal User Manual : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. - - Note ● Devices with fingerprint module support fingerprint function. Refers to the actual device. ● Some models support WiFi function. Refers to the actual device.
DS-K1T690 Series Face Recognition Terminal User Manual Note The device should be added to the center, or the calling operation will be failed. Enter password to authenticate.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page.
DS-K1T690 Series Face Recognition Terminal User Manual 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Enter the password. - If you have added an administrator for the device, tap and enter the password.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-3 Home Page 7.2 Communication Settings You can set the wired network, the Wi-Fi parameter, the RS-485 parameters, the Wiegand parameters and access to Hik-Connect on the communication settings page.
DS-K1T690 Series Face Recognition Terminal User Manual 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wired Network. Figure 7-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK.
DS-K1T690 Series Face Recognition Terminal User Manual Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.
DS-K1T690 Series Face Recognition Terminal User Manual 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. ● Output: A face recognition terminal can connect an external access controller.
DS-K1T690 Series Face Recognition Terminal User Manual 3. Enable Access to Hik-Connect 4. Enter Server IP. 5. Create the Verification Code, and you need to enter the verification code when you manage the devices via Hik-Connect. 7.3 User Management On the user management interface, you can add, edit, delete and search the user. 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2.
DS-K1T690 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5. Optional: Add a face picture, fingerprints, cards, or Pin for the administrator. ● Note For details about adding a face picture, see Add Face Picture . ● Note For details about adding a fingerprint, see Add Fingerprint . ● For details about adding a card, see Add Card .
DS-K1T690 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Face Picture field to enter the face picture adding page. Figure 7-8 Add Face Picture 6. Look at the camera.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page. 7. Tap Save to save the face picture. 8.
DS-K1T690 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Fingerprint field to enter the Add Fingerprint page. 6. Follow the instructions to add a fingerprint. Note ● The same fingerprint cannot be repeatedly added. ● Up to 10 fingerprints can be added for one user.
DS-K1T690 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 6. Tap the Card field and tap +. 7. Configure the card No. - Enter the card No. manually. - Present the card over the card presenting area to get the card No. Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8.
DS-K1T690 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the PIN code to view the PIN code. Note The PIN code cannot be edited. It can only be applied by the platform. 6. Set the user role. Administrator The user is the administrator.
DS-K1T690 Series Face Recognition Terminal User Manual Search User On the User Management page, Tap the search area to enter the Search User page. Tap Card on the left of the page and select a search type from the drop-down list. Enter the employee ID, card No., or the user name for search. Tap to search. Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow the steps in User Management to edit the user parameters. Tap to save the settings.
DS-K1T690 Series Face Recognition Terminal User Manual 7.4.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data or Face Data. 4. Enter the created password when you exported the data. If you do not create a password when you exported the data, leave a blank in the input box and tap OK immediately.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● ● Note The supported USB flash drive format is DB. The system supports the USB flash drive with the storage of 1G to 32G. Make sure the free space of the USB flash drive is more than 512M. The exported user data is a DB file, which cannot be edited. 7.5 Identity Authentication After network configuration, system parameters configuration and user configuration, you can go back to the initial page for identity authentication.
DS-K1T690 Series Face Recognition Terminal User Manual 7.5.2 Authenticate via Multiple Credential Before You Start Set the user authentication type before authentication. For details, see Set Authentication Mode . Steps 1. If the authentication mode is Card and Face, Password and Face, Card and Password, Card and Face and Fingerprint, authenticate any credential according to the instructions on the live view page. Note ● The card can be normal IC card, or encrypted card.
DS-K1T690 Series Face Recognition Terminal User Manual Sound Settings You can enable/disable the voice prompt function and adjust the voice volume. Note You can set the voice volume between 0 and 10. Time Settings Set the time zone, the device time and the DST. Beauty You can enable the beauty function and set the smooth and the whiten parameter. Tap + or - to control the effect strength. Note By default, the function is disabled. Sleep Set the device sleeping waiting time (minute).
DS-K1T690 Series Face Recognition Terminal User Manual Parameter Description Note You can input the number from 1 to 10. Wide Dynamic It is suggested to enable the WDR function if installing the device outdoors. When there are both very bright and very dark areas simultaneously in the view, you can enable the WDR function to balance the brightness of the whole image and provide clear images with details. Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode.
DS-K1T690 Series Face Recognition Terminal User Manual Parameter Description If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open. Must Wear If the person do not wear a face mask when authenticating, the device prompts a notification and the door keeps closed. None If the person do not wear a face mask when authenticating, the device will not prompt a notification.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-11 Temperature Measurement Parameters The available parameters descriptions are as follows: Temp. Detection When enabling the function, the device will authenticate the permissions and at the same time take the temperature. When disabling the device, the device will authenticate the permissions only. Normal Temp. Edit the threshold according to actual situation.
DS-K1T690 Series Face Recognition Terminal User Manual Measurement Area Configure the temperature measurement area. Unit Select a temperature unit according to your preference. 7.9 Set Access Control Parameters You can set the access control permissions, including the functions of terminal auth. mode, reader auth. mode, enable NFC card, auth. via QR Code, door contact, open duration (s) and authentication interval (s). On the Home page, tap Access Control to enter the Access Control Settings page.
DS-K1T690 Series Face Recognition Terminal User Manual Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face. Reader Auth.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 7-13 Preference Settings Theme You can set the theme of the prompt window on the authentication page. You can select Theme as Iris Recognition Mode/Advertisement/Meeting/Simple. Advertisement After selecting this mode, the advertising area and identification authentication area of the device will be displayed on separate screens. Video and advertising information playback, welcome speech display are supported.
DS-K1T690 Series Face Recognition Terminal User Manual You should set a room No. When you tap the call button on the authentication page, you can call the configured room directly without dialing. Call APP When you tap the call button on the authentication page, you will call the mobile client where the device is added. Password Enable this function amd you can enter the password to authenticate via password. QR Code You can use the QR code scanning function on the authentication interface.
DS-K1T690 Series Face Recognition Terminal User Manual Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of administrator, user, face picture, card, and event. ● ● Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. The capacity varies according to the configured enrollment rules. For details about setting enrollment rules, see .
DS-K1T690 Series Face Recognition Terminal User Manual 3. Click Device Management to enter the Device Management interface. 4. Add the device to the client software. Note For details about adding device, see Add Device. 5. Call the client software. 1) Tap on the device initial page. 2) Enter 0 in the pop-up window. 3) Tap to call the client software. 6. Tap Answer on the pop-up page of the client software and you can start two-way audio between the device and the client software.
DS-K1T690 Series Face Recognition Terminal User Manual 7.12.3 Call Device from Client Software Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management page. 4. Add the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K1T690 Series Face Recognition Terminal User Manual 7.12.5 Call Mobile Client from Device Steps 1. Get the mobile mobile client from the supplied disk or the official website, and install the software according to the prompts. 2. Run the mobile client and add the device to the mobile client. Note For details, see the user manual of the mobile client. 3. Enter Basic Settings → Shortcut Key and enable Call APP. 4. Go back to the initial page and call the mobile client. 1) Tap on the device initial page.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K1T690 Series Face Recognition Terminal User Manual Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream.
DS-K1T690 Series Face Recognition Terminal User Manual Add Face Picture Click User → Add to enter the Add Person page. Click + on the right to upload a face picture from the local PC. Note The picture format should be JPG or JPEG or PNG, and the size should be less than 200 K. Click Save to save the settings. Add Authentication Mode Click User → Add to enter the Add Person page. Set the authentication mode. Click Save to save the settings. 8.4 Search Event Click Search to enter the Search page.
DS-K1T690 Series Face Recognition Terminal User Manual Steps 1. Click Device Management to enter the settings page. Figure 8-3 Device Management 2. Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add. 3. Click Import. Enter the information of the device in the template to import devices in batch. 4. Click Export to export the information to the PC. 5. Select the device and click Delete to remove the selected device from the list. 6.
DS-K1T690 Series Face Recognition Terminal User Manual You can also click Open to open the file folder to view details. Set Captured Pictures Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 8.6.2 View Device Information View the device name, language, model, serial No.
DS-K1T690 Series Face Recognition Terminal User Manual You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.6.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-5 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-6 Upgrade and Maintenance Page Click Reboot to start reboot the device. Or you can check Reboot Automatically to set desired reboot mode by selecting Reboot by Duration or Reboot by Time and set the corresponding parameters. Click Save. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage.
DS-K1T690 Series Face Recognition Terminal User Manual Import Click and select the file to import. Click Import to start import configuration file. Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. Note Do not power off during the upgrading. 8.6.7 Log Query You can search and view the device logs.
DS-K1T690 Series Face Recognition Terminal User Manual In order to increase the network security level when visiting websites, you can enable HTTP to acquire a more secure and encrypted network communication environment. The communication should authenticated by identity and encryption password after enabling HTTP, which is save. 8.6.9 Certificate Management It helps to manage the server/client certificates and CA certificate. Note The function is only supported by certain device models.
DS-K1T690 Series Face Recognition Terminal User Manual Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1. Go to Configuration → System → Security → Certificate Management . 2. Create an ID in the Inport CA Certificate area. Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 8.6.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3.
DS-K1T690 Series Face Recognition Terminal User Manual 8.6.12 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → User Management → Arming/Disarming Information . You can view the device arming/disarming information. Click Refresh to refresh the page. 8.6.13 Network Settings Set TCP/IP, port, SIP, WiFi, report strategy, platform access and ISUP. Note Some device models do not support Wi-Fi settings. Refer to the actual products when configuration.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-7 TCP/IP Settings Page Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, and the IPv4 default gateway automatically. NIC Type Select a NIC type from the drop-down list. By default, it is Auto.
DS-K1T690 Series Face Recognition Terminal User Manual DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Port Parameters Set the HTTP, RTSP and HTTPS port parmaeters. Click Configuration → Network → Basic Settings → Port . HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login.
DS-K1T690 Series Face Recognition Terminal User Manual - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click Network Settings. 2) Set the IP address, subnet mask, and default gateway. Or check Enable DHCP and the system will allocate the IP address, subnet mask, and default gateway automatically. Click OK. 5. SIP Setting Steps 1. Click Network → Basic Settings → SIP to enter the settings page.
DS-K1T690 Series Face Recognition Terminal User Manual Note Hik-Connect is an application for mobile devices. With the App, you can view live image of the device, receive alarm notification and so on. 3. Check the checkbox of Enable to enable the function. 4. Optional: Check the checkbox of Custom, and you can set the server address by yourself. 5. Create a Stream Encryption/Encryption Key for the device. Note 6 to 12 letters (a to z, A to Z) or numbers (0 to 9), case sensitive.
DS-K1T690 Series Face Recognition Terminal User Manual Steps 1. Click Configuration → Network → Advanced → HTTP Listening . 2. Edit the destination IP or host name, URL and port. 3. Optional: Click Test to test whether the entered IP address or host name are valid. 4. Optional: Click Default to reset the destination IP or host name. 5. Click Save. 8.6.14 Set Video and Audio Parameters Set the image quality, resolution, and the device volume. Set Video Parameters Click Configuration → Video/Audio → Video .
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-9 Video Settings Page Set the video channel, the stream type, the video type, resolution, the bitrate type, video quality, the frame rate, the Max. bitrate, the video encoding, and I frame interval. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio .
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-10 Set Audio Parameters Drag the block to adjust the device input and output volume. Click Save to save the settings after the configuration. You can also enable Voice Prompt. Note The functions vary according to different models. Refers to the actual device for details. 8.6.15 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1. Click Configuration → Video/Audio → Prompt .
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-11 Customize Audio Content 2. Select Prompt as TTS(Text to Speech) to turn the text to audio content. 3. Select time schedule. 4. Enable the function. 5. Set the appellation. 6. Set the time period when authentication succeeded. 1) Click Add. 2) Set the time duration and the language. Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content.
DS-K1T690 Series Face Recognition Terminal User Manual Note If authentication is failed in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. Optional: Add holiday schedule. 8. 1) Click Add to add holiday schedule. 2) Repeat step 3 to 6. 9. Click Save to save the settings. 8.6.
DS-K1T690 Series Face Recognition Terminal User Manual 8.6.17 Set Supplement Light Brightness Set the device supplement light brightness. Steps 1. Click Configuration → Image → Supplement Light Parameters . Figure 8-12 Supplement Light Settings Page 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 8.6.18 Set Beauty Parameters You can enable beauty camera and set the parameters. Steps 1.
DS-K1T690 Series Face Recognition Terminal User Manual After selecting Automatic, the device will enter automatically enter the image fusion mode. You need to set set the Sensitivity. The larger the value, the higher the sensitivity, and the easier it is for the device to enter the image fusion mode. Disable The device will not enter the image fusion mode automatically. 8.6.
DS-K1T690 Series Face Recognition Terminal User Manual Set Manual Attendance via Web Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Manual. 3. Enable the Attendance Status Required and set the attendace status lasts duration. 4.
DS-K1T690 Series Face Recognition Terminal User Manual Set Manual and Auto Attendance via Web Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page.
DS-K1T690 Series Face Recognition Terminal User Manual Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters. If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list.
DS-K1T690 Series Face Recognition Terminal User Manual Select an authentication mode according to your actual needs from the drop-down list. Multiple People Authentication Multiple people can be authenticated at the same time. Recognition Interval If the interval between card presenting of the same card is less than the configured value, the card presenting is invalid. Authentication Interval You can set the authentication interval of the same person when authenticating.
DS-K1T690 Series Face Recognition Terminal User Manual Drag the block or enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time. Overwriting The earliest 5% events will be deleted when the system detects the stored events has been over 95% of the full space.
DS-K1T690 Series Face Recognition Terminal User Manual Clear Registered Face Pictures All registered pictures in the device will be deleted. Clear Captured Pictures All captured pictures in the device will be deleted. Set Card Security Click Configuration → General → Card Security to enter the settings page. Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data.
DS-K1T690 Series Face Recognition Terminal User Manual Full Card No. All card No. will be read. Wiegand 26 (3 bytes) The device will read card via Wiegand 26 protocol (read 3 bytes). Wiegand 34 (4 bytes) The device will read card via Wiegand 34 protocol (read 4 bytes). 8.6.22 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage. Click Configuration → Intercom → Device No. .
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-13 Device No. Settings Device Type The device can be used as a door station or outer door station. Select a device type from the drop-down list. Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● Note If you change the No., you should reboot the device. The main door station No. is 0, and the sub door station No. ranges from 1 to 16. Phase No. Set the device phase No. Building No. Set the device building No. Unit No. Set the device unit No. Note If you change the No., you should reboot the device. If set the device type as Outer Door Station, you can set the period No., outer door station No., and community No. Outer Door Station No.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-14 Session Settings 2. Set registration password, main station IP, private server IP and enable Protocol 1.0. Registration Password Activation password of the main station. Main Station IP IP address of the main station. Private Server IP IP address of the private server. Enable Protocol 1.0 After enabling, the device is registered to the main station through the previous protocol.
DS-K1T690 Series Face Recognition Terminal User Manual Number Settings Link the room No. and SIP numbers. Click Configuration → Intercom → Device No. to enter the page. Figure 8-15 Number Settings 1. Set the Device Type. 2. Set the Floor No.. 3. Set the Door Station No.. 4. You can also set the Phase No., Building No. and Unit No. in advanced settings. 5. Click Save.
DS-K1T690 Series Face Recognition Terminal User Manual 8.6.23 Access Control Settings Set Door Parameters Click Configuration → Access Control → Door Parameters . Figure 8-16 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked.
DS-K1T690 Series Face Recognition Terminal User Manual You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open. Door Lock Powering Off Status You can set the door lock status when the door lock is powering off. By default, it is Remain Closed.
DS-K1T690 Series Face Recognition Terminal User Manual RS-485 Address Set the RS-485 Address according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. Baud Rate The baud rate when the devices are communicating via the RS-485 protocol. Set Wiegand Parameters You can set the Wiegand transmission direction.
DS-K1T690 Series Face Recognition Terminal User Manual Input The device can connect a Wiegand card reader. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. Drag the block to set the time interval and pulse width. 4. Note ● The time interval ranges from 1 ms to 20 ms. ● The pulse width ranges from 1 us to 100 us. 5. Click Save to save the settings.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-18 Access Control and Elevator Control 2. Check Enable Elevator Control. 3. Set the elevator parameters. Elevator No. Select an elevator No. for configuration from the drop-down list. Elevator Controller Type Select an elevator controller from the drop-down list. Interface Type Select a communication type from the drop-down list for elevator communication.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● ● Note Up to 4 elevator controllers can be connected to 1 device. Up to 10 negative floors can be added. Make sure the interface types of elevator controllers, which are connected to the same device, are consistent. 8.6.
DS-K1T690 Series Face Recognition Terminal User Manual Enable Temperature Detection When enabling the function, the device will authenticate the permissions and at the same time take the temperature. When disabling the device, the device will authenticate the permissions only. Over-Temperature Alarm Threshold (Max./Min.) Edit the threshold according to actual situation. If the detected temperature is higher or lower than the configured parameters, an alarm will be triggered. By default, the value is 37.3°.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-20 Black Body Settings 2. Enable black body correction function. 3. Put a black body in front of the camera. Make sure there are no other objects between the camera and the black body. 4. Set the distance between the black body and the camera (straight line), the emissivity of the black body, and the temperature unit. Note The black body's temperature is fixed. 5. Click Calibrate, and draw the black body's position on the page.
DS-K1T690 Series Face Recognition Terminal User Manual Set Basic Parameters Click Configuration → Smart → Smart . Note The functions vary according to different models. Refers to the actual device for details. Figure 8-21 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T690 Series Face Recognition Terminal User Manual Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Live Face Detection Security Level After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication. Recognition Distance Select the distance between the authenticating user and the device camera.
DS-K1T690 Series Face Recognition Terminal User Manual Face Recognition Timeout Value Set the timeout value when face recognizing. If the face recognition time is longer than the configured value, the system will pop up a prompt. ECO Mode After enabling the ECO mode, the device will use the IR camera to authenticate faces in the low light or dark environment. And you can set the ECO mode threshold, ECO mode (1:N), and ECO mode (1:1).
DS-K1T690 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Set Recognition Area Click Configuration → Smart → Area Configuration . Drag the yellow frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system. Click Save to save the settings.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 8-22 Meeting Plans 2. Set Meeting Room Name, Meeting Theme, and Host. 3. Set Start Time and End Time of the meeting. 4. Add Participants. Note You can add by entering names or work numbers to inquire device workers. 5. Drag the block to set the advanced check-in time and the latest check-in time. Note ● The advanced check-in time ranges from 1 min to 255 min. ● The latest check-in time ranges from 1 min to 255 min. 6. Select the check-in type.
DS-K1T690 Series Face Recognition Terminal User Manual Single Participant Only one of the participant attending the meeting checks in. All Participants All of the participant attending the meeting check in. Disable You can diable this function and participants attending the meeting don't have to check in. 7. Click Save. 8.6.27 Set Notice Publication You can set the screen saver and the sleep time for the device. Click Configuration → Notice Publication .
DS-K1T690 Series Face Recognition Terminal User Manual Simple After selecting this mode, the live view of the authentication page will be disabled, and in the meanwhile, the person's name, employee ID, face pictures will all be hidden. Normal After selecting this mode, the device displays the video preview screen and performs authentication. Advertisement After selecting this mode, the advertising area and identification authentication area of the device will be displayed on separate screens.
DS-K1T690 Series Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T690 Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T690 Series Face Recognition Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T690 Series Face Recognition Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T690 Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T690 Series Face Recognition Terminal User Manual 9.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T690 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 9.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 9.4.
DS-K1T690 Series Face Recognition Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T690 Series Face Recognition Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T690 Series Face Recognition Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 9.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T690 Series Face Recognition Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by Local Mode. 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. Click the Card No. column and enter the card number. 6. - Place the card on the card enrollment station.
DS-K1T690 Series Face Recognition Terminal User Manual Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E.
DS-K1T690 Series Face Recognition Terminal User Manual 9.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K1T690 Series Face Recognition Terminal User Manual Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2.
DS-K1T690 Series Face Recognition Terminal User Manual 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 9.
DS-K1T690 Series Face Recognition Terminal User Manual Figure 9-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T690 Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 9-4 Data Synchronization 9.
DS-K1T690 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Before You Start Add access control device to the client. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T690 Series Face Recognition Terminal User Manual Press Key to Enter Card Number If you enable this function, you can input the card No. by pressing the key. Wi-Fi Probe If you enable this function, the device can probe the surrounding communication devices' MAC address and upload the MAC address to the system. If the MAC address match the specified MAC address, the system can trigger some linkage actions. 3G/4G If you enable this function, the device can communicate in 3G/4G network.
DS-K1T690 Series Face Recognition Terminal User Manual You can set the exit button as remaining closed or remaining open. Usually, it is remaining open. Door Locked Time After swiping the normal card and relay action, the timer for locking the door starts working. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card.
DS-K1T690 Series Face Recognition Terminal User Manual Steps 1. Click Access Control → Advanced Function → Device Parameter . 2. In the device list on the left, click to expand the door, select a card reader and you can edit the card reader's parameters on the right. 3. Edit the card reader basic parameters in the Basic Information page. ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows.
DS-K1T690 Series Face Recognition Terminal User Manual Select the fingerprint recognition level in the drop-down list. Default Card Reader Authentication Mode View the default card reader authentication mode. Fingerprint Capacity View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance.
DS-K1T690 Series Face Recognition Terminal User Manual user cannot authenticate via the fake face within 5 minutes. Within the 5 minutes, the user can authenticate via the real face twice continuously to unlock. Application Mode You can select indoor or others application modes according to actual environment. 4. Click OK. 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s).
DS-K1T690 Series Face Recognition Terminal User Manual Passing Mode Select the controller which will control the barrier status of the device. ● If you select According to Lane Controller's DIP Settings, the device will follow the lane controller's DIP settings to control the barrier. The settings on the software will be invalid. ● If you select According to Main Controller's Settings, the device will follow the settings of the software to control the barrier.
DS-K1T690 Series Face Recognition Terminal User Manual 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Face Recognition Terminal. 4. Set the parameters. Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface.
DS-K1T690 Series Face Recognition Terminal User Manual 5. Set the baud rate, data bit, the stop bit, parity type, communication mode, working mode, and connection mode in the drop-down list. Note When the connection mode is Connect Access Control Device, you can select Card No. or Person ID as the output type. 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically.
DS-K1T690 Series Face Recognition Terminal User Manual 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. The sector ID ranges from 1 to 100. 6. Click Save to save the settings. 9.
DS-K1T690 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T690 Series Face Recognition Terminal User Manual Before You Start You have added person(s) and access control device(s) to the client. For details, refer to Person Management and Add Device . Steps 1. Click Monitoring to enter monitoring module. Real-time access records are displayed on the bottom of the page. You can view record details, including card No., person name, event time, door location, temperature, authentication type etc.
DS-K1T690 Series Face Recognition Terminal User Manual 7. Optional: Click picture). to view details (including person's detailed information and the captured Note In the pop-up window, you can click to view details in full screen.
DS-K1T690 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T690 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T690 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T690 Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K1T690 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T690 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T690 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD24752B
