MODEL#HLDS01-RGT-BLK
Pilot PACKAGE CONTENTS Hi Igniter Lo PART A B C D E F G H I J K L 1 A Reflector B Emitter C Support D Protective Guard E Ruby Quartz Glass Tube F Burner Ignition Plate G Control Box Casing H Gas Hose & Regulator I Back Panel J Front Door Panel K Wheel Kit L Bottom plate DESCRIPTION Reflector Emitter Support Protective Guard Ruby Quartz Glass Tube Burner Ignition Plate Control Box Casing Gas Hose & Regulator Back Panel Front Door Panel Wheel Kit Base plate QUANTITY 1 1 3 3 1 1
WARNlNG SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRlOR TO OPERATION OF THE HEATER FOR YOUR SAFETY If you smell gas: 1 Shut off gas to the appliance. 2 Extinguish any open flame. 3 If odor continues, immediately call your gas supplier or your fire Department. FOR YOUR SAFETY 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance 2.
WARNING Read the instructions before installation and use.
INCLUDED HARDWARE (6 Already Preassembled) (2 for wheels) OO EE HH DD Wrench Qty. 1 Bolt M10 ×15mm Qty. 2 Nut M8 Qty. 11 Screw M8×15 mm Qty. 16 ADDITIONAL REQUIRED HARDWARE MM FF Screw M5×10 mm Qty. 12 Screw M8×30 mm Qty. 1 (Already Preassembled) SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This manual contains important information about the assembly, operation and maintenance of this patio heater.
SAFETY INFORMATION DANGER DANGER DANGER WARN DANGER 5
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone. WARNING will sink to the lowest level possible.
ASSEMBLY INSTRUCTIONS 1. First please ensure all transit protection (foam, cardboard, bubble wrap, etc.) is removed. Carefully put the ruby quartz glass tube aside after removing the bubble wrap and foam material .Then install emitter to reflector with Nut M8 ① and ② as shown in picture 1 Top portion Bottom panels Wheel kit Hardware Used Nut M8 Qty. 9 Wrench Qty. 1 Base plate 2. Remove three protective steel guards 2 Top View Hardware Used Philips screwdriver Qty.
ASSEMBLY INSTRUCTIONS 3 Top portion Bottom panels Wheel kit Hardware Used Base plate 4 4. Then place 1pc of ceramic rope into emitterand 1pc of ceramic rope into glass tubeholder at bottom Top View Hardware Used Wrench Qty.
ASSEMBLY INSTRUCTIONS 6 6. Tighten the Nut M8 on the reflector.Then use Bolt M8 to tighten the small hat on top of the reflector. Top portion Bottom panels Wheel kit Base plate 2 Hardware Used Top View Nut M8 Qty. 3 Bolt M8×30 mm Qty. 1 Wrench Qty. 1 Philips screwdriver Qty.
ASSEMBLY INSTRUCTIONS 7. Align bottom panel on top of base plate and connect them together by securely installing (5) M8×15 screws through the designated 90 degree metal brackets with a philips screwdriver. 7 Hardware Used DD Screw M8×15 mm x5 PP Philips screwdriver x1 8. Align top portion on top of bottom panel and connect them together by securely installing (5) M8×15 screws through the designated 90 degree metal brackets with a philips screwdriver.
ASSEMBLY INSTRUCTIONS 9 .Re-install the protective steel guard(D) by hanging it on the upper support slots.Next tightly secure it with all (12) of the M5×10 screws in to their original support slots accordingly. 9 MM D . Hardware Used MM Screw M5×10 mm x 12 PP Philips screwdriver x1 10. Propane Only-Proper Hose Connection. WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak, causing a fire.
1 ASSEMBLY INSTRUCTIONS 11. Connect hose and regulator to cylinder.The propane gas and cylinder are sold separately.Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 12 of the standard for storage and handling of liquefied petroleum gas, ANSI/NFPA 58 or CSA B149.1, Natural Gas and Propane Installation Code. Your local library or fire department should have this book.
OPERATION INSTRUCTIONS DANGER Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Note: This heater is equipped with a pilot light that allows for safer startups and shutdowns. Pilot must be lit before main burner can be started.
OPERATION INSTRUCTIONS 4. Push the igniter button until pilot flame is visible throughthe glass tube. 5. Once the pilot is lit, continue to depress the control knob for 30 seconds. 6. If the pilot does not stay lit, repeat steps 4 to 6. 7. If after repeating steps 4 to 6 unit does not light, then -Push in control knob and turn counterclockwise to “PILOT” (Figure 3). -As you are depressing the control knob, place long stem lighter through the glass tube to light the pilot (Figure 4). -Repeat step 6.
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 20 seconds before igniting the gas will cause a ball of flame upon ignition. When heater is ON: The "pilot light" should be blue with yellow top once burner is lit. The flame in the glass tube will be yellow in color.If excessive yellow flame is detected, turn offheater and consult “Troubleshooting” on page 18.
OPERATION INSTRUCTIONS 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 24 in. on top and at least 36 in. on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
CARE AND MAINTENANCE Gas odor Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Pilot won’t light Air in gas line Note: Heater operates Low gas pressure with cylinder valve fully open at reduced efficiency below 40ºF (5ºC) Igniter fails Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas Turn cylinder valve OFF and replace cylinder Use match to light pilot;
AZ Patio Heater, LLC (“Vendor”) warrants to the original retail purchaser of this heater to no other person, that if this heater is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one year from the date of purchase, all parts in such heater shall be free from defects in manufacturing and workmanship. Vendor may require reasonable proof of your date of purchase from an authorized retailer or distributor.
Pilot PACKAGE CONTENTS Hi Igniter Lo PART A B C D E F G H I J K L 20 A Reflector B Emitter C Support D Protective Guard E Ruby Quartz Glass Tube F Burner Ignition Plate G Control Box Casing H Gas Hose & Regulator I Back Panel J Front Door Panel K Wheel Kit L Bottom plate DESCRIPTION Reflector Emitter Support Protective Guard Ruby Quartz Glass Tube Burner Ignition Plate Control Box Casing Gas Hose & Regulator Back Panel Front Door Panel Wheel Kit Base plate QUANTITY 1 1 3 3 1
