Network Bullet Camera Quick Start Guide 0
Network Bullet Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Bullet Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Bullet Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Bullet Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Bullet Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Bullet Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be -30 °C to +60 °C, or -40 °C to 60 °C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ................................................................. 9 1.1 Type I Camera ................................................................. 9 1.2 Type II Camera .............................................................. 10 2 Installation .................................................................................... 13 2.1 Memory Card Installation .............................................. 13 2.
Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Type I Camera The overview of Type I camera is shown below. 2 1 3 7 8 9 10 4 DC12 V IN 11 56 Figure 1-1 Overview of Type I Camera Table 1-1 Description No.
Network Bullet Camera·Quick Start Guide No. Description 4 IR LED 5 Memory Card Slot 6 Reset Button 7 Camera Body 8 Bracket 9 Network Interface 10 Power Interface 11 CVBS Interface Note: Press RESET about 10 s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.2 Type II Camera The overview of Type II camera is shown below.
Network Bullet Camera·Quick Start Guide 2 1 3 7 8 9 4 DC1 2V IN 10 56 Figure 1-2 Overview of Type II Camera Table 1-2 Description No.
Network Bullet Camera·Quick Start Guide No. Description 7 Camera Body 8 Bracket 9 Network Interface 10 Power Interface Note: Press RESET about 10 s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3af). Make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide DC V 12IN Lock Screw Figure 2-1 Remove the Sun Shield 2. Rotate the front cover counterclockwise to remove it. DC V 12IN Figure 2-2 Remove the Front Cover 3. Insert the memory card into the memory card slot. DC1 2V IN Figure 2-3 Insert the Memory Card 4. Rotate the front cover clockwise back to the camera and replace the sun shield. 5. Tighten the lock screw clockwise to fix the sun shield.
Network Bullet Camera·Quick Start Guide DC V 12IN Figure 2-4 Fix the Front Cover 2.2 Ceiling/Wall Mounting Before you start: Camera of these types is equipped with a bracket. It can be mounted to a wall or a ceiling directly. Steps: 1. Paste the drill template (supplied) to the wall or the ceiling where you intend to install the camera. 2. Drill screw holes in the wall or ceiling according to the drill template.
Network Bullet Camera·Quick Start Guide 3. If you need to route the cables through the wall (or the ceiling), dill a cable hole according to the drill template. Skip this step if you want to route the cables on the surface of the wall (or the ceiling). 4. Route the cables of the camera. 5. Secure the camera to the wall (or the ceiling) with the supplied screws. Drill Template Drill Template Figure 2-6 Secure the Camera Note: ● The supplied screw package contains self-tapping screws, and expansion bolts.
Network Bullet Camera·Quick Start Guide Pan Adjustment Steps: 1). Loosen the lock screw 1. 2). Adjust the panning position of the camera. The adjusting range is from 0° to 360°. 3). Tighten the lock screw 1. Tilt Adjustment Steps: 1). Loosen the lock screw 2. 2). Adjust the tilting position of the camera. The adjusting range is from 0° to 90°. 3). Tighten the lock screw 2. Rotation Adjustment Steps: 1). Loosen the lock screw 3. 2). Rotate the rotation position to adjust the azimuth angle of the image.
Network Bullet Camera·Quick Start Guide 8. Adjust zoom and focus (refer to 2.3 Zoom and Focus Adjustment). 9. (Optional) Install the waterproof jacket for network interface. Refer to 2.4 Installation of Network Cable Waterproof Jacket (Optional) for detailed installation procedures. 2.3 Zoom and Focus Adjustment 2.3.1 Type I Purpose: You can use the zoom lever and focus lever to adjust the zoom and focus level. Follow the steps below to adjust focus and zoom. Steps: 1.
Network Bullet Camera·Quick Start Guide Zoom/Focus Lever DC12 V IN Figure 2-8 Zoom and Focus Adjustment Note: If the camera is equipped with a fixed lens, you don’t need to adjust the zoom and focus. 2.3.2 Type II Camera of this type is equipped with a motorized varifocal lens. You can adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client software. For detailed steps, refer to the User Manual of Network Camera.
Network Bullet Camera·Quick Start Guide 2.4 Installation of Network Cable Waterproof Jacket (Optional) Purpose: If the camera is installed outdoor, you can adopt the waterproof accessory for the network cable after the camera is secured on the installation surface. ① ② ③ ④ ⑤ ⑥ ⑦ Figure 2-10 Waterproof Accessory Components Table 2-1 Components No.
Network Bullet Camera·Quick Start Guide Steps: 1. Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (the rubber gasket inset ridge must face the waterproof endcap), and the waterproof endcap ④ in order. 2. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. 3. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. 4.
Network Bullet Camera·Quick Start Guide Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
Network Bullet Camera·Quick Start Guide 3 Set the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Bullet Camera·Quick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for activation via client software. 3.2.
Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide 5. Click OK to save the password and enter the live view interface. 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2.
Network Bullet Camera·Quick Start Guide 3. Create and input the new password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification. For IP address modification via client software, refer to the user manual of client software. Steps: 1. Run the SADP software. 2. Select an active device. 3.
Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Bullet Camera·Quick Start Guide 5 Operate via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Bullet Camera·Quick Start Guide 7. Save the settings. 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Bullet Camera·Quick Start Guide 2. In the Hik-Connect app, tap “+” on the upper-right corner and then scan the QR code of the camera to add the camera. You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera.
Network Bullet Camera·Quick Start Guide 5.4 Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD07021B-B 0
