Network Speed Dome Quick Start Guide
Network Speed Dome·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Speed Dome·Quick Start Guide USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Network Speed Dome·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Network Speed Dome·Quick Start Guide Do not drop the speed dome or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid installation on vibrations surface or places subject to shock (ignorance can cause device damage). Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the speed dome will not be used for an extended period, replace the lens cap to protect the sensor from dirt.
Network Speed Dome·Quick Start Guide Table of Contents 1 Overview ...................................................................................................... 1 1.1 Speed Dome Overview ............................................................................................ 1 1.1.1 Overview of N4xxx Series Speed Dome ............................................................. 1 1.1.2 Overview of N4xxxI Series (IR) Speed Dome ..................................................... 2 1.1.
Network Speed Dome·Quick Start Guide 1 Overview 1.1 Speed Dome Overview The network speed dome has three types: N4xxx Series N4xxxI Series (IR) N5xxxI Series (IR) Note: The figures below are for reference only, refer to the actual product as the standard. 1.1.
Network Speed Dome·Quick Start Guide 1.1.2 Overview of N4xxxI Series (IR) Speed Dome Figure 1-2 Overview of N4xxxI Series (IR) Speed Dome 1.1.
Network Speed Dome·Quick Start Guide 1.2 Cable Interfaces The cable interfaces of the speed dome are shown in Figure 1-4. The cables are distinguished by different colors. Refer to the labels attached on the cables for identification. Notes: The cables vary depending on different speed dome models. Make sure the speed dome is power-off before you connect the cables.
Network Speed Dome·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Do not touch the bubble directly by hand. The image blurs otherwise. Do not power the speed dome up until the installation is finished. To ensure the safety of personnel and equipment, all the installation steps should be done with power supply off.
Network Speed Dome·Quick Start Guide Steps: 1. Disassemble the speed dome. 1) Loosen three screws and remove the bubble. 2) Remove the protective lens cover, foam, and sticker. Protective Foam Bubble Protective Sticker Figure 2-2 Disassemble the Speed Dome 2. Install the memory card. Memory Card Slot Figure 2-3 Memory Card Slot 3. Drill screw holes in the ceiling. 1) Attach the drill template to the ceiling where you want to install the speed dome.
Network Speed Dome·Quick Start Guide Toggle Bolt Holes Figure 2-4 Toggle Bolt Holes 3) Rotate the bolts through the screw holes. 4) Install the toggles back as shown in Figure 2-5. Toggle Bolt Figure 2-5 Install the Toggle Bolts 5. Install the speed dome to the ceiling. 1) Align the toggle bolts with the screw holes on the ceiling. 2) Push the speed dome to the mounting hole on the ceiling. 3) Rotate the bolts again. The toggle will automatically rotate down to secure the speed dome to the ceiling.
Network Speed Dome·Quick Start Guide 4) Secure the bubble to the speed dome with three screws as shown in Figure 2-7. Screws Figure 2-7 Secure the Bubble 6. Route the cables through the ceiling. 7. Remove the protective film on the bubble after the installation is finished. 2.2 Installing N4xxxI Series (IR) Speed Dome 2.2.1 Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket.
Network Speed Dome·Quick Start Guide Loosen four screws Memory Card Slot Figure 2-8 Memory Card Slot 3) Install the rear cover back and tighten the lock screws. 2. Install the bracket. 1) Get the bracket and screws from the packing box as shown in Figure 2-9. Figure 2-9 Wall Mounting Bracket 2) Drill four screw holes in the wall according to the holes on the bracket, and then insert four M8 expansion screws into the mounting holes.
Network Speed Dome·Quick Start Guide Figure 2-11 Safety Rope 2) 3) 4) 5) Route the cables through the bracket and connect the corresponding cables. Loosen the lock screws on the bracket. Align the speed dome with bracket and rotate it to the bracket tightly. Tighten the two lock screws with the wrench to secure the speed dome and the bracket. Figure 2-12 Secure the Speed Dome 4. Remove the protective film on the bubble after the installation is finished.
Network Speed Dome·Quick Start Guide 2.2.2 In-ceiling Mounting Note: The height of the space above the ceiling must be more than 250 mm. The thickness of the ceiling must range from 5 mm to 40 mm. The ceiling must be strong enough to withstand more than four times the weight of the speed dome and the accessories. Steps: 1. Install the memory card. Note: Refer to step 1 in Section 2.2.1 Wall Mounting. 2. Drill screw holes in the ceiling.
Network Speed Dome·Quick Start Guide 5. Install the speed dome to the ceiling. 1) Align the toggle bolts with the screw holes on the ceiling. 2) Push the speed dome according to the direction of the arrow in Figure 2-14 to the mounting hole. Figure 2-14 Push to the Mounting Hole 3) Rotate the screws clockwise and the toggle will rotate down to secure the speed dome to the ceiling. Fix the locks on the ceiling.
Network Speed Dome·Quick Start Guide Figure 2-16 Install the Trim Ring 7. Remove the protective film on the bubble after the installation is finished. 2.3 Installing N5xxxI Series (IR) Speed Dome Notes: Refer to Section 2.2.1 Wall Mounting for wall mounting steps for N5xxxI series (IR) speed dome. Refer to Figure 2-17 for memory card slot of N5xxxI (IR) series speed dome.
Network Speed Dome·Quick Start Guide 3 Setting the Speed Dome over the LAN Notes: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact with your dealer or the nearest service center. To ensure the network security of the speed dome, we recommend you to have the speed dome assessed and maintained termly.
Network Speed Dome·Quick Start Guide Activation via web browser, activation via SADP, and activation via client software are supported. We will take activation via SADP software and activation via web browser as examples to introduce the speed dome activation. 3.2.1 Activation via Web Browser Steps: 1. Power on the speed dome. Connect the speed dome to your computer or the switch/router which your computer connects to. 2.
Network Speed Dome·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the speed dome. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select an inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the speed dome in batch.
Network Speed Dome·Quick Start Guide 3.3 Modifying the IP Address Purpose: To view and configure the speed dome via LAN (Local Area Network), you need to connect the network speed dome in the same subnet with your PC. Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification.
Network Speed Dome·Quick Start Guide 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by SADP. Refer to the user manual of SADP for details.
Network Speed Dome·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024 × 768 resolution or higher Web Browser: Internet Explorer 8 to 11, Google Chrome 31 to 44, and Mozilla Firefox 30 to 51 Steps: 1. Open the web browser. 2.
Network Speed Dome·Quick Start Guide Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above step 2 to step 4 to login. Note: For detailed instructions of further configuration, refer to the user manual of network speed dome.
Network Speed Dome·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the speed dome, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain speed dome models. 5.1 Enable Hik-Connect Service on Speed Dome Purpose: Hik-Connect service should be enabled on your speed dome before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Speed Dome·Quick Start Guide 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the speed dome before enabling the service. Refer to Section 3.2 Activating the Speed Dome. Steps: 1. Access the speed dome via web browser. Refer to Chapter 4 Accessing via Web Browser. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. 4. 5. 6.
Network Speed Dome·Quick Start Guide 5.3 Adding Speed Dome to Hik-Connect Before you start: You need to enable the Hik-Connect service on speed dome before adding it to your Hik-Connect account. Refer to Section 5.1 Enable Hik-Connect Service on Speed Dome. Steps: 1. Use a network cable to connect the speed dome with a router if the speed dome does not support Wi-Fi.
Network Speed Dome·Quick Start Guide Note: For detailed information, refer to the user manual of the Hik-Connect app. 5.4 Initializing the Memory Card Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the speed dome such as motion detection.
Network Speed Dome·Quick Start Guide 24 UD08090B
