Use and Care Manual

ManualsBrandsHilti ManualsTools & HardwareSDT 5 Stand up Decking Tool

*2061808*

2061808

SDT 5

Bedienungsanleitung de

Operating instructions en

Mode d’emploi fr

Istruzioni d’uso it

Manual de instrucciones es

Manual de instruções pt

Gebruiksaanwijzing nl

Brugsanvisning da

Bruksanvisning sv

Bruksanvisning no

Käyttöohje 

Οδηγιεςχρησεως el

Használati utasítás hu

Instrukcjaobsługi pl

Инструкцияпозксплуатации ru

Návod k obsluze cs

Návod na obsluhu sk

Upute za uporabu hr

Navodila za uporabo sl

Ръководствозаобслужване bg

Instrucţiunideutilizare ro

KulllanmaTalimatı tr

Lietošanaspamācība lv

Instrukcija lt

Kasutusjuhend et

IНСТРУКЦIЯЗЕКСПЛУАТАЦIЇ uk

Пайдаланубойыншабасшылы

қ kk

Summary of content (12 pages)

PAGE 1
SDT 5 Bedienungsanleitung de Mode d’emploi fr Operating instructions Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Οδηγιες χρησεως Használati utasítás Instrukcja obsługi Инструкция по зксплуатации en it es pt nl da sv no fi el hu pl ru Návod k obsluze cs Upute za uporabu hr Návod na obsluhu Navodila za uporabo Ръководство за обслужване Instrucţiuni de utilizare Kulllanma Talimatı Lietošanas pamāc
PAGE 2
1 ꙣ Ꙭ Ꙥ ꙫ ꙥ Ꙧ Ꙫ ꙩ ꙧ Ꙩ
PAGE 3
2 3 1 1 4 3 3 2 4 3 2 4 5 4 1 2 3 3 3 6 2 4 5 1
PAGE 4
6 1 3 2 7 8 1 9 3 2 10 2 1 2
PAGE 5
11 2 1 3 4 4
PAGE 6
ORIGINAL OPERATING INSTRUCTIONS SDT 5 stand-up tool en It is essential that the operating instructions are read before the appliance is operated for the first time. Always keep these operating instructions together with the appliance. Ensure that the operating instructions are with the appliance when it is given to other persons.
PAGE 7
Symbols Read the operating instructions before use. Location of identification data on the appliance The type designation and the serial number are stamped on the rear of the appliance. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. en 2 Description 2.1 Use of the product as directed The stand-up decking fastening tool is an accessory for use with Hilti metal construction screwdrivers.
PAGE 8
5 Safety instructions 5.1 Basic information concerning safety en Observe the safety information and the operating instructions for the Hilti metal construction screwdriver used. In addition to the information relevant to safety given in each of the sections of these operating instructions, the following safety instructions must be strictly observed at all times. The Hilti metal construction screwdriver can then be used in the stand-up tool with maximum safety. 5.
PAGE 9
6.1.4 Fitting the Hilti metal construction screwdriver 3 1. 2. 3. Release the wing nut at the clamping bar on the main module. Open the clamping bar. Insert the Hilti metal construction screwdriver into the top end of the main barrel. 4. 5. 6. Close the clamping bar. Secure the Hilti metal construction screwdriver by tightening the wing nut. Pass the supply cord through the supply cord strain relief clasp on the grip. NOTE Feed a loop of the cord through from below and then pull it over the clip.
PAGE 10
8 Care and maintenance CAUTION Before beginning cleaning, unplug the supply cord or remove the battery from the power tool in order to prevent unintentional starting. en DANGER Remove the ST 1800‑A screwdriver, bit and magazine guide from the stand-up tool. 8.1 Care of screwdriving bits Clean off dirt and dust deposits adhering to the screwdriving bits and spindle and protect them from corrosion by wiping them from time to time with an oil-soaked rag. 8.
PAGE 11
This constitutes Hilti’s entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.
PAGE 12
Hilti Corporation 2061808 / A2 2061808 Hilti = registered trademark of Hilti Corp., Schaan W 4256 | 1212 | 00-Pos. 1 | 1 Printed in Liechtenstein © 2012 Right of technical and programme changes reserved S. E. & O. *2061808* LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.