Operating Instruction SF 6-A22/SF 6H-A22 (02)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 Inserting the battery
- 5.2 Removing the battery
- 5.3 Charging the battery
- 5.4 Installing the side handle
- 5.5 Fitting the belt hook (optional)
- 5.6 Installing Hilti bit holder (optional)
- 5.7 Hilti Installing the retaining strap (optional)
- 5.8 Selecting the gear
- 5.9 Setting forward or reverse rotation
- 5.10 Inserting / removing the accessory tool
- 5.11 Drilling
- 5.12 Hammer-action drilling
- 5.13 Screwdriving
- 5.14 Switching on
- 5.15 Switching off
- 6 Care and maintenance
- 7 Transport and storage of cordless tools
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Introduction de l'accu
- 5.2 Retrait de l'accu
- 5.3 Recharge de l'accu
- 5.4 Montage de la poignée latérale
- 5.5 Montage de la patte d'accrochage (en option)
- 5.6 Montage du porte-embout Hilti (en option)
- 5.7 Montage de la sécurité anti-chute Hilti (en option)
- 5.8 Choix du régime
- 5.9 Sélection du sens de rotation droite / gauche
- 5.10 Mise en place/Retrait de l'outil amovible
- 5.11 Perçage
- 5.12 Perçage à percussion
- 5.13 Vissages
- 5.14 Mise en marche
- 5.15 Arrêt
- 6 Nettoyage et entretien
- 7 Transport et stockage des appareils sur accu
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Manejo
- 5.1 Colocación de la batería
- 5.2 Extracción de la batería
- 5.3 Carga de la batería
- 5.4 Montaje de la empuñadura lateral
- 5.5 Montaje del colgador de cinturón (opcional)
- 5.6 Montaje del soporte para puntas de Hilti (opcional)
- 5.7 Montaje de la protección en caso de caída de Hilti (opcional)
- 5.8 Selección de velocidad
- 5.9 Ajuste del giro a la derecha o a la izquierda
- 5.10 Introducción y extracción del útil de inserción
- 5.11 Taladrar
- 5.12 Taladrar con percusión
- 5.13 Atornillado
- 5.14 Conexión
- 5.15 Desconexión
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento de las herramientas alimentadas por batería
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização
- 5.1 Colocar a bateria
- 5.2 Retirar a bateria
- 5.3 Carregar a bateria
- 5.4 Montagem do punho auxiliar
- 5.5 Montar o gancho de cinto (opcional)
- 5.6 Montar o suporte de bit Hilti (opcional)
- 5.7 Montar o dispositivo de segurança Hilti (opcional)
- 5.8 Seleccionar a velocidade
- 5.9 Ajustar a rotação à direita ou à esquerda
- 5.10 Colocar/retirar o acessório
- 5.11 Furar
- 5.12 Furar com percussão
- 5.13 Aparafusar
- 5.14 Ligar
- 5.15 Desligar
- 6 Conservação e manutenção
- 7 Transporte e armazenamento de ferramentas de baterias recarregáveis
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
2 English 2231427
*2231427*
These numbers refer to the corresponding illustrations found at the
beginning of these operating instructions
The numbering reflects the sequence of operations shown in the
illustrations and may deviate from the steps described in the text
Item reference numbers are used in the overview illustrations and
refer to the numbers used in the product overview section
This symbol is intended to draw special attention to certain points
when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:
Wireless data transfer
Hilti Li-ion battery type series used. Observe the information given in
the section headed Intended use.
Li-ion battery
Direct current (DC)
Drilling without hammer action
Drilling with hammer action (hammer drilling)
Protection class II (double-insulated)
Rated speed under no load
Revolutions per minute
1.4 Product information
products are designed for professional users and only trained,
authorized personnel are permitted to operate, service and maintain the
products. This personnel must be specifically informed about the possible
hazards. The product and its ancillary equipment can present hazards if
used incorrectly by untrained personnel or if used not in accordance with
the intended use.
The type designation and serial number are printed on the rating plate.
▶ Write down the serial number in the table below. You will be required to
state the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
Drill/driver SF 6-A22 | SF 6H-A22
Generation 02
Serial no.
Printed: 19.08.2019 | Doc-Nr: PUB / 5467429 / 000 / 01