Operating Instruction TE 6-A22 (04)
Table Of Contents
- Original operating instructions
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 2.1 Indications générales de sécurité pour les appareils électriques
- 2.2 Indications générales de sécurité applicables aux burineurs
- 2.3 Consignes de sécurité supplémentaires spécifiques au perforateur-burineur
- 2.4 Consignes de sécurité applicables au module récupérateur de poussières
- 2.5 Utilisation et emploi soigneux des accus
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation
- 6 Travail
- 7 Nettoyage et entretien
- 8 Transport et stockage
- 9 Aide au dépannage
- 10 Accessoires optionnels
- 11 Recyclage
- 12 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Manejo
- 5.1 Preparación del trabajo
- 5.2 Colocación de la batería
- 5.3 Extracción de la batería
- 5.4 Montaje de la empuñadura lateral
- 5.5 Montaje y ajuste del tope de profundidad
- 5.6 Montaje/desmontaje del portaútiles
- 5.7 Inserción del útil
- 5.8 Extracción del útil
- 5.9 Realización de trabajos por encima de la cabeza
- 5.10 Colocación del cincel
- 6 Procedimiento de trabajo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento
- 9 Ayuda en caso de averías
- 10 Accesorios opcionales
- 11 Reciclaje
- 12 Garantía del fabricante
- Manual de instruções original
*2166239*
2166239 English 9
▶ It is essential that the dust shield is replaced if the sealing lip is damaged.
8 Transport and storage
8.1 Transport and storage of cordless tools and batteries
Transport
CAUTION
Accidental starting during transport !
▶ Always transport your products with the batteries removed!
▶ Remove the battery/batteries.
▶ Never transport batteries loose and unprotected. During transport, batteries should be protected from
excessive shock and vibration and isolated from any conductive materials or other batteries that may
come in contact with the terminals and cause a short circuit. Comply with the locally applicable
regulations for transporting batteries.
▶ Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged
batteries.
▶ Prior to each use and before and after prolonged transport, check the product and the batteries for
damage.
Storage
WARNING
Accidental damage caused by defective or leaking batteries !
▶ Always store your products with the batteries removed!
▶ Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in
the technical data.
▶ Do not store batteries on the charger. Always remove the battery from the charger when the charging
operation has completed.
▶ Never leave batteries in direct sunlight, on sources of heat, or behind glass.
▶ Store the product and batteries where they cannot be accessed by children or unauthorized persons.
▶ Prior to each use and before and after prolonged storage, check the product and the batteries for
damage.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
9.1 The rotary hammer is not in working order
Malfunction Possible cause Action to be taken
The LEDs on the battery indi-
cate nothing.
The battery is not fully inserted. ▶ Push the battery in until it
engages with a double click.
Battery is discharged. ▶ Change the battery and charge
the empty battery.
The battery is too hot or too cold. ▶ Allow the battery to cool
down or to warm up to room
temperature.
1 LED on the battery blinks. Battery is discharged. ▶ Change the battery and charge
the empty battery.
The battery is too hot or too cold. ▶ Allow the battery to cool
down or to warm up to room
temperature.
4 LEDs on the battery blink. The rotary hammer has been over-
loaded briefly.
▶ Release the control switch and
then press it again.