TE 30A36 Printed: 30.04.
Printed: 30.04.
TE 30A36 Original operating instructions Printed: 30.04.
Printed: 30.04.
1 Information about the documentation 1.1 • • • About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
Drilling without hammering action Drilling with hammering action (hammer drilling) Chiseling Chisel positioning Forward / reverse Diameter Rated speed under no load Revolutions per minute 1.4 Product information products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards.
Personal safety ▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. ▶ Use personal protective equipment. Always wear eye protection.
2.3 Additional safety instructions for breakers Personal safety ▶ Use the product only when it is in technically faultless condition. ▶ Never tamper with or modify the tool in any way. ▶ When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A sudden break-through can affect your balance! ▶ Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking through.
3 Description 3.1 Product overview @ Chuck ; Depth gauge release button English Printed: 30.04.
= % & ( Depth gauge Function selector switch Forward / reverse switch Control switch 3.2 ) + § / Battery state of charge / fault display Release buttons / battery state of charge display Battery Side handle Intended use The product described is a cordless (battery-powered) combihammer with pneumatic hammering mechanism. It is designed for drilling in concrete, masonry, wood and metal. The product can also be used for light to medium-duty chiseling on masonry and surface finishing work on concrete.
3.7 Items supplied Combihammer, side handle with depth gauge, operating instructions. To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com 4 Technical data Rated voltage Weight 5 Operation 5.1 Preparations at the workplace TE 30A36 36 V 11.2 lb (5.
5.1.2 Removing the battery 1. Press the release buttons on the battery. 2. Pull the battery out toward the rear. 5.1.3 Charging the battery Make sure that the outer surfaces of the battery are clean and dry before inserting the battery in the approved battery charger. Read the operating instructions for the charger for further information about the charging process. ▶ Use an approved charger to charge the battery. 5.1.
5.1.5 1. 2. 3. 4. Adjusting the depth gauge (optional) Press the release button on the side handle. Adjust the depth gauge to the desired drilling depth. Release the release button. Check that the side handle is securely attached. 5.1.6 Removing the chuck CAUTION Risk of injury. The depth gauge, if fitted but not used, might hinder the operator. ▶ Remove the depth gauge from the product. Set the function selector switch to the “Chiseling” position for changing the chuck. 1.
1. 2. 3. 4. Remove the battery from the tool. Grip the chuck as shown in the illustration and pull the three chuck release rings upwards. Fit the chuck onto the chuck mount. Rotate the chuck until it engages in position. 5.1.8 Inserting the tool 1. Lightly grease the connection end of the accessory tool. ➥ Use only genuine Hilti grease. Using the wrong grease can result in damage to the tool. 2. Push the accessory tool into the chuck as far as it will go (until it engages). 3.
5.1.9 Removing the accessory tool CAUTION Risk of injury! The accessory tool gets hot during use. ▶ Wear protective gloves when changing the accessory tool. ▶ Do not place the hot accessory tool on readily flammable materials. ▶ Pull the chuck back as far as it will go and remove the accessory tool. 5.2 Types of work ATTENTION Risk of damage by incorrect handling! ▶ Do not operate the switches for direction of rotation and/or function selection during operation.
5.2.4 Chisel positioning Set the function selector switch to this symbol: . ➥ The chisel can be adjusted to 12 different positions (in 30° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working position. ▶ 5.2.5 Chiseling Set the function selector switch to this symbol: ▶ 5.2.6 . Forward / reverse Set the forward / reverse switch to the desired direction of rotation.
7 Transport and storage of cordless tools Transport CAUTION Accidental starting during transport ! ▶ Always transport your products with the batteries removed! ▶ ▶ ▶ Remove the battery. Never transport batteries in bulk form (loose, unprotected). Check the tool and batteries for damage before use after long periods of transport.
Trouble or fault The drill bit makes no progress. 8.2 Possible cause The combihammer is set to run in reverse rotation. Action to be taken ▶ Move the forward / reverse selector switch to the “Forward” position. The combihammer is not in working order. Malfunction No LEDs light. 1 LED blinks. 4 LEDs blink. Possible cause The battery is not fully inserted. ▶ The battery is discharged. ▶ The battery is too hot or too cold. ▶ The battery is discharged. ▶ The battery is too hot or too cold.
Printed: 30.04.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 30.04.
