SF BT 22A English Printed: 19.10.
Printed: 19.10.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of signs used 1.2.
Product information Drill Generation: Serial no.: SF BT 22A 01 2 Safety 2.1 General power tool safety warnings WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
▶ ▶ ▶ ▶ ▶ ▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Careful handling and use of batteries ▶ Do not use the battery as a power source for other unspecified appliances. ▶ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. ▶ Do not expose batteries to high temperatures, direct sunlight or fire. ▶ Do not disassemble, squash or incinerate batteries and do not subject them to temperatures over 80°C (176°F). ▶ Do not attempt to charge or continue to use damaged batteries.
English Printed: 19.10.
6 English Printed: 19.10.
3 Description 3.1 Overview of the product English Printed: 19.10.
@ ; = % & Keyless chuck Motor cooling air intake Grip Switch safety lock Control switch (with electronic speed control) ( ) + § / Belt hook Battery Air exit Battery release button Battery display 3.2 Intended use The product described is a hand-held cordless drill designed for drilling blind holes in steel using Hilti TXBT… stepped drill bits which is a prerequisite for driving Hilti XBT threaded studs. ▶ ▶ Use only Hilti lithiumion batteries of the B 18 / B 22 series with this product.
Status Meaning 1 LED blinks, the power tool is not ready for use. • 1 LED blinks, the power tool is ready for use. 4 LEDs blink, the power tool is not ready for use. • • Charge status: < 10 % The battery has overheated or is completely discharged. The power tool is overloaded or has overheated. Note Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds after releasing the control switch.
Push the battery into the drill from the rear until it is heard to engage with a click. ▶ 5.2 Removing the battery Remove the battery. ▶ 5.3 Fitting the belt hook (optional) WARNING Risk of injury! Hazard presented by a falling power tool. ▶ A falling power tool may present a risk of injury to yourself and others. Check that the belt hook is fitted securely before beginning work. Note The belt hook allows the drill to be attached to a belt worn by the operator.
▶ Fit the belt hook on the appropriate side of the drill. 5.4 Fitting or removing accessory tools CAUTION Risk of injury. The drill may start inadvertently. ▶ Make sure that the safety lock has been activated or that the battery has been removed from the drill. 1. Open the keyless chuck. 2. Check that the connection end of the accessory tool is clean and then insert it in the keyless chuck or, respectively, pull the accessory tool out of the keyless chuck. 3. Retighten the keyless chuck. 5.
6 Care and maintenance WARNING Electrical hazards. Improper repairs to electrical parts may lead to serious injuries. ▶ Electrical parts may be repaired only by trained electrical specialists. Note To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.
Trouble or fault The tool or battery gets very hot. Possible cause The tool is overloaded (application limits exceeded). Action to be taken ▶ Pay attention to the power and performance rating of the product before using it, i.e check its suitability for the job on hand. See “Technical data” section. 9 Manufacturer’s warranty ▶ Please contact your local Hilti representative if you have questions about the warranty conditions. English Printed: 19.10.
Printed: 19.10.
Printed: 19.10.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 19.10.