ABS Approval for Stainless Steel X-CR and Grating Fasteners

ManualsBrandsHilti ManualsDirect FasteningX-FCP-F Checker plate fastener (coated)

Certificate Number: 01-HS156800B-2-PDA

Confirmation of Product Type Approval 21/SEP/2011

Please refer to the "Service Restrictions" shown below to determine if Unit Certification is required for this product.

This is to certify that, pursuant to the Rules of the American Bureau of Shipping (ABS), the manufacturer of the

below listed product held a valid Manufacturing Assessment (MA) with expiration date of 30/AUG/2016. The

continued validity of the Manufacturing Assessment is dependent on completion of satisfactory audits as required

by the ABS Rules.

And; a Product Design Assessment (PDA) valid until 11/SEP/2016 subject to continued compliance with the Rules

or standards used in the evaluation of the product.

The above entitle the product to be called Product Type Approved.

The Product Design Assessment is valid for products intended for use on ABS classed vessels, MODUs or facilities

which are in existence or under contract for construction on the date of the ABS Rules used to evaluate the

Product.

ABS makes no representations regarding Type Approval of the Product for use on vessels, MODUs or facilities

built after the date of the ABS Rules used for this evaluation.

Due to wide variety of specifications used in the products ABS has evaluated for Type Approval, it is part of our

contract that; whether the standard is an ABS Rule or a non-ABS Rule, the Client has full responsibility for

continued compliance with the standard.

HILTI AKTIENGESELLSCHAFT

Model Name(s): Stainless powder-actuated Hilti X-CR fasteners

Presented to:

HILTI AKTIENGESELLSCHAFT

FELDKIRCHERSTR. 100,

POSTFACH 333

SCHAAN

Liechtenstein

Intended Service: For fastening of fastened materials to the base materials of carbon steel, stainless

steel, or aluminium, in the marine, offshore and industrial environment.

Description: General Purpose Fasteners: X-CR Threaded Studs: X-CRM, X-CRW Composite

Fasteners: X-FCM-R, X-FCM-M, X-FCP-R, X-FCP-F Stainless Steel Threaded

Studs, Nails and accessories whereby fastenings are made by using powder

actuated Tools to drive the fasteners into their final positions, by displacing base

material in the process. Composite fasteners are either made from stainless

material (X-FCM-R, X-FCP-R) or from duplex coated carbon steel (X-FCM-M,

X-FCP-F)

Ratings: For Rating Matrix and Product Test Reports refer to ABS Type Approval Certificate

and Hilti Direct Fastening Technology Manual for each product.

Service Restrictions: List of Recommended Areas and Applications: 1. The Hilti DX Fastenings are to be

used for fastened and base material of carbon steel, stainless steel, and aluminum

in the marine, offshore, and industrial environments, as applicable (Ref to: Product

Matrix). 2. To ensure that proper anchoring/fastening mechanisms take place, i.e.

clamping, keying, fusing, and brazing/soldering, besides the use of proper

fastening tools and power source, the following base material strengths are to

comply with; Carbon Steel : Ultimate Tensile Strength fu = 370 N/mm2 (53.53 ksi )

Stainless Steel : Ultimate Tensile Strength fu = 370 N/mm2 (53.53 ksi ) Aluminum :

Ultimate Tensile Strength fu = 200 N/mm2 (28.94 ksi ) 3. User of the DX fasteners

is to observe the Hilti Direct Fastening Technology Manual for application

limitations and conditions. 4. In general, type approved DX fasteners are not to be

Summary of content (3 pages)

PAGE 1
Certificate Number: 01-HS156800B-2-PDA Confirmation of Product Type Approval 21/SEP/2011 Please refer to the "Service Restrictions" shown below to determine if Unit Certification is required for this product. This is to certify that, pursuant to the Rules of the American Bureau of Shipping (ABS), the manufacturer of the below listed product held a valid Manufacturing Assessment (MA) with expiration date of 30/AUG/2016.
PAGE 2
Certificate Number: 01-HS156800B-2-PDA used in structural members that are sensitive to stress patterns/variations and for areas that notch toughness is of paramount importance. 5. In general, Hilti fasteners may be used to fasten materials in areas where welding or drilling for bolting is permissible. It is recommended that the fasteners be installed no closer than 15 mm from the edge of a flange or cutout and no closer than 15 mm between fasteners.
PAGE 3
Certificate Number: 01-HS156800B-2-PDA ABS Programs ABS has used due diligence in the preparation of this certificate and it represents the information on the product in the ABS Records as of the date and time the certificate was printed. Type Approval requires Drawing Assessment, Prototype Testing and assessment of the manufacturer's quality assurance and quality control arrangements. Limited circumstances may allow only Prototype Testing to satisfy Type Approval.