Installation Guide

Hilti, Inc. (US) 1-800-879-8000 | www
.us.hilti.com
I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www
.ca.hilti.com
I Pr
oduct T
echnical Guide 2006 263
M
echanical Anchoring Systems
HLC Sleeve Anchor 4.3.11
4.3.11.4 Installation Instructions
4.3.11.5 Ordering Information
1. Drill: Drill the hole. Clean hole with blow
out bulb. For hollow masonry, switch to
drilling only mode before penetrating
backside.
2. Insert: With the bolt flush to the top of the
nut, drive the sleeve anchor into the hole.
3. Set: Tighten anchor to the recommended
torque value. Over-torquing will reduce the
pullout and shear loads.
A
Bolt Head (H)
A
Minimum Fastens
Bit Diameter
1
Bolt Diameter Emed. Depth Materials Up To
Description Item No. in. in. in. (mm) in. (mm) Box Qty
Sleeve Anchor RS 1/4 x 1-1/4 00336238 1/4 3/16 1 (25) 1/4 (6.4) 100
Sleeve Anchor RS 1/4 x 2 00336239 1/4 3/16 1 (25) 1 (25) 100
Sleeve Anchor RS 1/4 x 4 00336240
1/4 3/16 1 (25) 3 (76) 100
Round Head Slotted (RS)
A
Flat Phillips Head (FPH)
1 For Hilti matched tolerance carbide tipped drill bits,
see section 8.4.1.
Sleeve Anchor AC 1/4 X 1-3/8
Nut Configuration
Outside diameter of sleeve, see
tables for threaded bolt diameter
Definition of Nomenclature
A: the overall length fr
om bottom
of washer to end of sleeve
Minimum Fastens
Bit Diameter
1
Bolt Diameter Emed. Depth Materials Up To
Description Item No. in. in. in. (mm) in. (mm) Box Qty
Sleeve Anchor H 5/16 x 1-5/8 00336244 5/16 1/4 1 (25) 5/8 (16) 100
Sleeve Anchor H 5/16 x 2-5/8 00336245 5/16 1/4 1 (25) 1-5/8 (41) 100
Sleeve Anchor H 3/8 x 1-7/8 00336252 3/8 5/16 1-1/4 (32) 5/8 (16) 50
Sleeve Anchor H 3/8 x 3 00336253 3/8 5/16 1-1/4 (32) 1-3/4 (44) 50
Sleeve Anchor H 1/2 x 2-1/4 00336259 1/2 3/8 1-1/2 (38) 3/4 (20) 50
Sleeve Anchor H 1/2 x 3 00336260 1/2 3/8 1-1/2 (38) 1-1/2 (38) 25
Sleeve Anchor H 1/2 x 4 00336261
1/2 3/8 1-1/2 (38) 2-1/2 (64) 25
Minimum Fastens
Bit Diameter
1
Bolt Diameter Emed. Depth Materials Up To
Description Item No. in. in. in. (mm) in. (mm) Box Qty
Sleeve Anchor FPH 1/4 x 1-3/8
00336234
1/4 3/16
1
(25) 3/8 (10) 100
Sleeve Anchor FPH 1/4 x 2 00336235 1/4 3/16 1 (25) 1 (25) 100
Sleeve Anchor FPH 1/4 x 3 00336236 1/4 3/16 1 (25) 2 (51) 100
Sleeve Anchor FPH 1/4 x 4 00336237 1/4 3/16 1 (25) 3 (76) 100
Sleeve Anchor FPH 3/8 x 2-7/8 00336248 3/8 5/16 1-1/4 (32) 1-1/2 (38) 50
Sleeve Anchor FPH 3/8 x 4 00336249 3/8 5/16 1-1/4 (32) 2-3/4 (70) 50
Sleeve Anchor FPH 3/8 x 5
00336250
3/8 5/16
1-1/4
(32) 3-3/4 (95) 25
Sleeve Anchor FPH 3/8 x 6
00336251
3/8
5/16
1-1/4
(32) 4-3/4 (120)
25
1
2 3