Operating Instruction GX 3 (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Loading the setting tool
- 6 Driving fasteners
- 7 Unloading the setting tool
- 8 Optional operating steps
- 9 Remedying possible malfunctions
- 10 Care and maintenance
- 11 Transport and storage
- 12 Troubleshooting
- 13 Disposal
- 14 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 3.1 Vue d'ensemble du produit
- 3.2 Utilisation conforme à l'usage prévu
- 3.3 Équipement livré
- 3.4 Canons
- 3.5 Éléments de fixation
- 3.6 Curseur de réglage de la profondeur d'implantation et déverrouillage du canon
- 3.7 Touche RESET
- 3.8 Pied d'appui
- 3.9 Patte d'accrochage à la ceinture
- 3.10 Cartouche de gaz
- 3.11 Indication du niveau de charge de la cartouche de gaz
- 4 Caractéristiques techniques
- 5 Chargement du cloueur
- 6 Implantation d'éléments de fixation
- 7 Déchargement du cloueur
- 8 Opérations optionnelles
- 9 Dépannage
- 10 Nettoyage et entretien
- 11 Transport et stockage
- 12 Aide au dépannage
- 13 Recyclage
- 14 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 3.1 Vista general del producto
- 3.2 Uso conforme a las prescripciones
- 3.3 Suministro
- 3.4 Guía clavos
- 3.5 Elementos de fijación
- 3.6 Corredera para el ajuste de la profundidad de fijación y el desbloqueo del guía clavos
- 3.7 Tecla RESET (reinicio)
- 3.8 Pie de apoyo
- 3.9 Colgador de cinturón
- 3.10 Carga de gas
- 3.11 Indicador del estado de la carga de gas
- 4 Datos técnicos
- 5 Carga de la fijadora
- 6 Colocación de elementos de fijación
- 7 Descarga de la fijadora
- 8 Pasos de manejo opcionales
- 8.1 Comprobación del estado de la carga de gas
- 8.2 Extracción del cargador
- 8.3 Colocación del cargador
- 8.4 Extracción del guía clavos
- 8.5 Colocación del guía clavos
- 8.6 Desmontaje del pie de apoyo
- 8.7 Montaje del pie de apoyo
- 8.8 Colocación del adaptador para una fijación única
- 8.9 Retirada del adaptador para una fijación única
- 9 Reparación de averías
- 10 Cuidado y mantenimiento
- 11 Transporte y almacenamiento
- 12 Ayuda en caso de averías
- 13 Reciclaje
- 14 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 3.1 Vista geral do produto
- 3.2 Utilização correcta
- 3.3 Incluído no fornecimento
- 3.4 Guias de pregos
- 3.5 Elementos de fixação
- 3.6 Cursor para ajuste da profundidade de fixação e desbloqueio da guia de pregos
- 3.7 Tecla RESET
- 3.8 Pé de apoio
- 3.9 Gancho de cinto
- 3.10 Lata de gás
- 3.11 Indicação do estado da lata de gás
- 4 Características técnicas
- 5 Carregamento da ferramenta de fixação
- 6 Fixação de elementos de fixação
- 7 Descarga da ferramenta de fixação
- 8 Passos de operação opcionais
- 9 Resolução de avarias
- 10 Conservação e manutenção
- 11 Transporte e armazenamento
- 12 Ajuda em caso de avarias
- 13 Reciclagem
- 14 Garantia do fabricante
*2126636*
2126636 English 9
7 Unloading the setting tool
7.1 Removing the gas can
1. Open the gas can compartment cover.
2. Press the gas can clip to release the gas can.
3. Remove the gas can from the gas can compartment.
4. Fit the cap on the gas can.
5. Close the gas can compartment cover.
7.2 Unloading the magazine
1. Pull the nail pusher back until it engages.
2. Remove all nail strips from the magazine.
WARNING
Risk of finger injury! Fingers could be pinched when the nail pusher is released.
▶ When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward slowly
as far as it will go.
3. Release the nail pusher and guide it forward as far as it will go.
7.3 Removing the single-fastener adapter
▶ After driving the fasteners, remove the single-fastener adapter ( → page 10) from the fastening tool.
8 Optional operating steps
8.1 Checking the status of the gas can
1.
Without pressing the fastening tool against the working surface, press the GAS button.
2. Read the gas can status from the display. → page 6
8.2 Removing the magazine
1. Pull the nail pusher back until it engages.
2. Remove the loose nail strips from the magazine.
WARNING
Risk of finger injury! Fingers could be pinched when the nail pusher is released.
▶ When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward slowly
as far as it will go.
3. Release the nail pusher and guide it forward as far as it will go.
4. Release the magazine locking catch.
5. Pivot the magazine about the pivot point towards the front.
6. Detach the magazine.
8.3 Fitting the magazine
1. Release the magazine locking catch.
2. Engage the front end of the magazine with the setting tool.
3. Pivot the magazine towards the setting tool as far as it will go.
4. Close the magazine locking catch.
8.4 Removing the fastener guide
1. Remove the gas can. → page 9
2.
Move the fastener guide release slider to the EJECT position.
3. Remove the fastener guide.
Printed: 07.06.2018 | Doc-Nr: PUB / 5261663 / 000 / 02