SR 6-A22 Printed: 23.01.
Printed: 23.01.
1 Information about the documentation 1.1 • • • About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols 1.2.
Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information ▶ Reciprocating saw Generation Serial no. 1.4 SR 6-A22 01 Declaration of conformity We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards.
▶ ▶ ▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
2.3 Additional safety instructions for saws Personal safety ▶ Keep your hands away from the cutting area and the blade. Keep your second hand on the auxiliary handle or the motor housing. When both hands are on the saw they cannot be injured by it. ▶ Use the product only when it is in perfect working order. ▶ Never tamper with or modify the power tool in any way. ▶ Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a risk of injury (cuts or burns).
▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ 2.5 ▶ ▶ ▶ ▶ ▶ Before cutting through pipes, make sure that they are empty of medium. Drain the pipes if necessary. When cutting through pipes, hold the power tool above the level of the pipe you are cutting through. ◁ The power tool is not protected against ingress of moisture. Liquid running out of a pipe can cause a short circuit in the power tool. Never cut into unknown materials and make sure the path of the saw is free of obstructions above and below the workpiece.
3 Description 3.1 Product overview 6 English Printed: 23.01.
@ ; = % & ( ) + 3.2 Blade holder Mount for cutting assist Folding scaffold hook (accessory) Transport lock Control switch Rear grip Battery state of charge indicator Battery release button § / : ∙ $ £ | Battery Front gripping area with locking button for contact shoe Saw blade release lever Dust removal adapter (accessory) Contact shoe Saw blade Cutting assist (accessory) Intended use The product described is a cordless reciprocating saw.
5.1 Removing the battery 1. Press the two release buttons and hold them in the pressed position. 2. Pull the battery out of the product to the rear. 5.2 1. 2. 3. 4. 5.3 Removing the saw blade Activate the transport lock or separate the battery from the power tool. Push the locking lever up as far as it will go and hold it in this position. Pull the blade forward out of the blade holder. Allow the locking lever to return to its original position. Replacing the contact shoe 1. Remove the battery.
2. 3. 4. 5. 6. Remove the saw blade. → page 8 Press the contact shoe lock button. Pull the contact shoe out. Press the contact shoe lock button. Insert the lightly greased contact shoe into the guide to the desired position. The contact shoe can be used in three positions. 7. Check that the contact shoe has engaged. 8. Insert the saw blade. → page 9 5.4 Installing the dust removal adapter (accessory) 1. Pull the contact shoe out. 2. Set the dust removal adapter on the contact shoe mount. 3.
1. Activate the transport lock or separate the battery from the power tool. 2. Check that the connection end of the accessory tool is clean and lightly greased. Clean it and grease it if necessary. 3. Push the locking lever up as far as it will go and hold it in this position. 4. Push the saw blade into the chuck from in front. 5. Allow the locking lever to return to its original position. 6. Grip and pull the saw blade to check that it is locked in position. 5.
6 Care and maintenance of cordless tools WARNING Risk of injury with battery inserted ! ▶ Always remove the battery before carrying out care and maintenance tasks! Care and maintenance of the tool • Carefully remove stubborn dirt from the tool. • Clean the air vents carefully with a dry brush. • Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these may attack the plastic parts. Care of the Liion batteries • Keep the battery free from oil and grease.
Trouble or fault The saw blade can’t be removed from the chuck. 8.2 Possible cause The locking lever was not pushed as far as it will go. Action to be taken ▶ Push the locking lever as far as it will go and remove the saw blade. The reciprocating saw is operational. Trouble or fault The tool does not achieve full power. The saw blade can’t be removed from the chuck. 9 Possible cause The control switch is not fully pressed. Action to be taken ▶ Press the control switch fully.
Printed: 23.01.
Printed: 23.01.
Printed: 23.01.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 23.01.