SID 14A SID 22A SIW 14A SIW 22A English Printed: 27.07.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
The type designation and serial number are printed on the type identification plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Type: Generation: Serial no.: SID 14-A, SID 22-A SIW 14-A, SIW 22-A 01 2 Safety 2.1 General safety precautions for power tools WARNING! Read all safety precautions and other instructions.
▶ tool cannot be guaranteed. If any parts are damaged, have these parts repaired before using the tool. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control. Using and handling the cordless power tool ▶ Use only the specified batteries in the power tools. Use of any other batteries may present a risk of injury and fire.
▶ If the battery is too hot to touch, it may be defective. In this case, place the power tool in a non-flammable location, well away from flammable materials, where it can be kept under observation and left to cool down. Contact Hilti Service after the battery has cooled down. 4 Printed: 27.07.
3 Description 3.1 Product overview 7 Printed: 27.07.
@ ; = % Hex. socket (SID) Illumination Forward/reverse selector switch with safety lock Control switch (with electronic speed control) Square drive (SIW) Torque selector button Belt hook (optional) Battery state of charge indicator Release buttons (B18/B22 battery) Release button (B14 battery) & ( ) + § / 3.2 Intended use The product described is a hand-held cordless impact screwdriver.
Large high-strength bolts SIW 14A 1 /4″ hex. socket with locking ring 1 /2″ square drive with ball-notch retention or 3/8″ square drive with locking ring SID 22A SIW 22A 3.3 lb (1.5 kg) 3.3 lb (1.5 kg) M6 to M12 Socket/bit drive Rated voltage Weight (including battery and chuck) Rated speed under no load SID 14A Setting I Setting II Setting III Impact speed 21.6 V 21.6 V 0 Hz …16.7 Hz (0 /min …1,000 /min) 0 Hz …16.7 Hz (0 /min …1,000 /min) 0 Hz …25.
SIW 14A Torque Setting I Setting II Setting III 1/2″ square drive with ballnotch retention 3/8″ square drive with locking ring 89 ftlbf (120 Nm) 85 ftlbf (115 Nm) 59 ftlbf (80 Nm) 48 ftlbf (65 Nm) 136 ftlbf (185 Nm) 118 ftlbf (160 Nm) SIW 22A 1/2″ square drive with ballnotch retention 3/8″ square drive with locking ring 100 ftlbf (135 Nm) 89 ftlbf (120 Nm) 66 ftlbf (90 Nm) 55 ftlbf (75 Nm) 148 ftlbf (200 Nm) 129 ftlbf (175 Nm) 5 Operation 5.
Note The belt hook allows the power tool to be attached to a belt worn by the operator. The belt hook can be fitted to allow attachment on the left or right side of the body. ▶ Fit the belt hook. 5.3 Fitting an accessory tool SID 14A SID 22A 1. Check that the connection end of the accessory tool is clean. Result The connection end is dirty. ▶ Clean the connection end. 2. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 3.
1. 2. 3. 4. Set the forward/reverse switch to the middle position or remove the battery from the power tool. Pull the chuck ring forward and hold it in this position. Pull the accessory tool out of the chuck. Release the chuck ring. 5.5 Fitting an accessory tool SIW 14A SIW 22A 1. Check that the connection end of the accessory tool is clean. Result The connection end is dirty. ▶ Clean the connection end. 2. Set the forward/reverse switch to the middle position or remove the battery from the power tool.
1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Pull the accessory tool off the square drive. 5.7 Setting the torque Technical data Model SID … (SID 14A OR SID 22A) ?? → page 9 Model SIW … (SIW 14A OR SIW 22A) ?? → page 9 ▶ Press the torque selector button as many times as necessary until the desired torque setting is indicated to the left of the button. SID 14A SID 22A Model SID … ?? → page 9 SIW 14A SIW 22A Model SIW … ?? → page 9 5.
Set the forward/reverse switch to the desired direction of rotation. ▶ 5.9 Screwdriving WARNING Risk of injury and damage. Screws/bolts or the workpiece may be damaged by excessively high torque; this may also lead to serious injury. ▶ Ensure that the fastener and attachment will withstand the level of torque generated by the tool. 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Use the torque selector button to set the desired torque. → page 13 5.
6 Care, maintenance, transport and storage 6.1 Care and maintenance of cordless tools WARNING Danger of electric shock! Carrying out care and maintenance while the battery is fitted presents a risk of serious physical injury and burning injury. ▶ Always remove the battery before carrying out all care and maintenance tasks. Care and maintenance of the tool • Carefully remove any dirt that may be adhering to parts. • Clean the air vents carefully with a dry brush.
7 Troubleshooting If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service. Trouble or fault The power tool doesn’t run. Possible cause The battery is not fully inserted. Action to be taken ▶ Push the battery in until it engages with an audible double click. Low battery. ▶ The forward/reverse selector switch is in the middle position. ▶ Push the forward/reverse switch to the left or right. Low battery.
Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00 ** Hilti = registered trademark of Hilti Corp.
