TE 7-C Operating instructions en Mode d’emploi fr Manual de instrucciones es Manual de instruções pt
1 This Product is Listed Ce produit est homologué Producto homologado por Este produto está registrado
2 3 4 5 6 7 8 9
ORIGINAL OPERATING INSTRUCTIONS TE 7‑C rotary hammer en It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons. Contents 1. General information 2. Description 3. Insert tools, accessories 4. Technical data 5. Safety instructions 6. Before use 7. Operation 8. Care and maintenance 9.
Obligation signs Wear eye protection en Wear a hard hat Wear ear protection Wear protective gloves Wear breathing protection Alternating current Hertz Rated speed under no load Revolutions per minute Diameter Double insulated Reverse rotation Forward rotation Location of identification data on the power tool The type designation can be found on the type identification plate and the serial number on the side of the motor housing.
2.2 Chucks TE‑C CLICK chuck 2.3 Switches Speed control switch for smooth starting. Function selector switch: Drilling without hammering Hammer drilling Chisel adjustment (18 positions) Chiseling en 2.4 Grips Vibration-absorbing, pivotable side handle with depth gauge Vibration-absorbing grip 2.5 Protective feature Mechanical slip clutch 2.6 Lubrication Oil lubrication 2.
2.9 Using extension cords outdoors When working outdoors, use only extension cords that are approved and correspondingly marked for this application. 2.10 Using a generator or transformer en This power tool may be powered by a generator or transformer which fulfills the following conditions: The unit must provide a power output in watts of at least twice the value printed on the rating plate on the power tool.
Power tool TE 7‑C Rated voltage Rated current input Mains frequency Weight of the tool, including side handle Dimensions (L x W x H) Drilling speed without hammering Hammer drilling speed Single impact energy 120 V 6.3 A 60 Hz 3.5 kg 341 mm x 86 mm x 217 mm 0…900/min 740/min 2.6 J Other information about the power tool Chuck Drilling performance in medium-hard concrete Protection class en TE‑C Click Ø 16 mm: 56 cm³/min Protection class I (grounded) or protection class II (double insulated).
en 5.1.3 Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
e) f) g) h) workpiece. Touching rotating parts, especially rotating insert tools, may lead to injury. Always lead the supply cord and extension cord away from the power tool to the rear while working. This helps to avoid tripping over the cord while working. Children must be instructed not to play with the power tool. The power tool is not intended for use by children, by debilitated persons or those who have received no instruction or training.
c) If the work involves breaking right through, take the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. en hat, ear protection, protective gloves and breathing protection while the machine is in use. 5.3.5 Personal protective equipment The user and any other persons in the vicinity must wear ANSI Z87.1-approved eye protection, a hard 6. Before use 3. 6.
7.1.2 Fitting the insert tool 4 CAUTION Wear protective gloves when changing the insert tool. 1. 2. 3. 4. 5. 6. Disconnect the supply cord plug from the power outlet. Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if necessary. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is found to be damaged (please refer to the “Care and maintenance” section).
en 7.2.2 Drilling without hammering 8 1. Turn the function selector switch until it engages in the “Drilling without hammering” position. Do not operate the function selector switch while the motor is running. 2. Bring the side handle into the desired position and check that it is fitted correctly and secured. 3. Plug the supply cord into the power outlet. 4. Position the power tool and drill bit at the point where the hole is to be drilled. 5.
The outer casing of the power tool is made from impact-resistant plastic. Sections of the grip are made from a synthetic rubber material. Never operate the power tool when the ventilation slots are blocked. Clean the ventilation slots carefully using a dry brush. Do not permit foreign objects to enter the interior of the power tool. Clean the outside of the power tool at regular intervals with a slightly damp cloth. Do not use a spray, steam pressure cleaning equipment or running water for cleaning.
Fault Possible cause Remedy The power tool doesn’t achieve full power. The extension cord’s conductor cross section is inadequate. The drill bit doesn’t rotate. The control switch is not pressed fully. The function selector switch is not engaged or is in the “Chiseling” or “Chisel adjustment” position. The drill bit can’t be released. The chuck is not pulled back fully. The drill bit makes no progress. The forward/reverse switch is set to reverse rotation.
Hilti Corporation 202931 / A 202931 Hilti = registered trademark of Hilti Corp., Schaan W 3090 0406 00-Pos. 3 1 Printed in China © 2006 Right of technical and programme changes reserved S. E. & O. *202931* LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.
