VC 125-6 VC 125-9 Español Printed: 07.03.
Printed: 07.03.
1 Información sobre la documentación 1.1 Acerca de esta documentación • • • Lea detenidamente esta documentación antes de la puesta en servicio. Ello es imprescindible para un trabajo seguro y un manejo sin problemas. Respete las indicaciones de seguridad y las advertencias presentes en esta documentación y en el producto. Conserve este manual de instrucciones siempre junto con el producto y entregue el producto a otras personas siempre acompañado del manual. 1.2 Explicación de símbolos 1.2.
1.4 Declaración de conformidad Bajo nuestra exclusiva responsabilidad, declaramos que el producto aquí descrito cumple con las directivas y normas vigentes. Encontrará una reproducción del organismo certificador al final de esta documentación. La documentación técnica se encuentra depositada aquí: Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE 2 Seguridad 2.1 Indicaciones de seguridad importantes ¡ADVERTENCIA! LEA ÍNTEGRAMENTE ESTAS INSTRUCCIONES.
▶ ▶ ▶ ▶ ▶ piezas no estén dañadas. Para garantizar un funcionamiento adecuado de la herramienta, las piezas deben estar correctamente montadas y cumplir todas las condiciones necesarias. Procure que la herramienta sea reparada únicamente por profesional cualificado y que se utilicen exclusivamente piezas de repuesto originales. Durante el trabajo, retire siempre hacia la zona de detrás de la herramienta el cable eléctrico, el alargador y la manguera de aspiración.
2.7 Sustancias aspiradas ▶ ▶ ▶ ▶ ▶ ▶ ▶ 4 No aspire polvo peligroso para la salud, inflamable o explosivo (polvo de magnesio-aluminio, entre otros). No deben aspirarse materiales cuya temperatura supere los 60 °C (140 °F), p. ej. cigarrillos encendidos o cenizas calientes. No se deben aspirar líquidos inflamables, explosivos o agresivos (refrigerantes, lubricantes, gasolina, disolvente, ácidos [pH < 5], lejías [pH > 12,5], etc.). No aspire objetos que puedan ocasionar daños a través del saco de polvo (p.
3 Descripción 3.1 Vista general del producto Español Printed: 07.03.
@ ; = % & ( Cubierta del filtro Gancho para cables Interruptor de conexión/desconexión Cabezal de aspiración Pieza de empalme de entrada Depósito de suciedad ) + § / : ∙ Pinza de cierre Botón de limpieza del filtro Empuñadura Fijación de la manguera Fijación de accesorios Pinza de cierre de la cubierta del filtro 3.2 Uso conforme a las prescripciones Los productos descritos aquí son aspiradores industriales universales destinados a usos profesionales.
Cantidad de llenado de agua Conexión de la manguera de aspiración (C-DN/C-ID) Presión negativa (máx.) Temperatura ambiente (máx.) Clase de protección Tipo de protección VC 125-6 VC 125-9 1,4 in (35 mm) 1,4 in (35 mm) 3 liq. galUS (13 ℓ) 3,2 psi (220 mbar) 104 ℉ (40 ℃) I IPX4 7 liq. galUS (26 ℓ) 3,2 psi (220 mbar) 104 ℉ (40 ℃) I IPX4 5 Puesta en servicio 5.1 Primera puesta en servicio 1. 2. 3. 4. 5. 6. Abra las dos pinzas de cierre. Separe el cabezal de aspiración del depósito de suciedad.
ADVERTENCIA Riesgo de lesiones. Si se daña el sistema de filtración pueden producirse fugas de polvo dañino para la salud. ▶ En caso de emergencia (p. ej., si se rompe el filtro), desconecte el aspirador, extraiga el enchufe de la toma de corriente y antes de volver a utilizar el aspirador, solicite a una persona especializada que lo compruebe. Indicación Asegúrese de que el aspirador no se desplace ni se caiga. 6.
6.5 Vaciado del depósito de suciedad sin saco para polvo (en caso de líquidos) 1. Extraiga el enchufe de red de la toma de corriente. 2. Levante el cabezal de aspiración del depósito de suciedad y colóquelo en una superficie de trabajo plana. 3. Sujete por la cavidad de agarre e incline el depósito de suciedad para vaciarlo. 4. Limpie el borde del depósito de suciedad con un paño. 5. Coloque el cabezal de aspiración en el depósito de suciedad y cierre las dos pinzas de cierre.
7.3 Inserción/cambio del elemento de filtro 1. 2. 3. 4. 5. 6. 7. 8. Extraiga el enchufe de red de la toma de corriente. Abra la pinza de cierre para la cubierta del filtro. Abra la cubierta del filtro. Extraiga cuidadosamente el elemento de filtro sujetándolo por las cavidades de agarre del soporte. Limpie la superficie de la junta con un paño. Introduzca el nuevo elemento de filtro. Cierre la cubierta del filtro plegando hacia delante el bloqueo de la tapa.
7.6 Transporte La herramienta no debe transportarse llena. La herramienta no debe colgarse de una grúa. ▶ En caso necesario, retire del soporte el Power Conditioner o la herramienta suelta. ▶ Vacíe la herramienta antes de ser transportada a otra ubicación. ▶ No incline la herramienta ni la transporte en horizontal si se han aspirado líquidos. ▶ Junte los dos extremos de la manguera para transportarla con ayuda del adaptador cónico. 7.
12 Español Printed: 07.03.
Printed: 07.03.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 07.03.