TE 3000-AVR Operating instructions en Mode d’emploi fr Manual de instrucciones es Manual de instruções pt
1 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado C US
2 긵 긶 긷 긹 긺 길
3
4 4 5 3 ! A 2 5 4 5 3 ! 2 B
TE-H28P SM 400 mm 500 mm TE-H28P FM 400 mm 500 mm TE-H28P SPM 80/400 mm 80/500 mm TE-H28P SPMA 125/450 mm TE-H28P SPI 500 mm TE-H28 400 mm TE STP 150 x 150 mm 200 x 200 mm
ORIGINAL OPERATING INSTRUCTIONS TE 3000‑AVR Breaker It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons. Contents 1. General information 2. Description 3. Accessories, consumables 4. Technical data 5. Safety instructions 6. Before use 7. Operation 8. Care and maintenance 9.
Obligation signs Wear eye protection en Wear a hard hat Wear ear protection Wear protective gloves Location of identification data on the power tool The type designation and serial number can be found on the type identification plate on the machine or tool. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: Generation: 02 Wear safety shoes Serial no.
2.2 Chuck 28 mm hex. chuck 2.3 Switch On / off switch en 2.4 Grips Grips incorporating AVR Active Vibration Reduction 2.5 Lubrication Permanent lubrication with separate lubrication chambers for the gearing and hammering mechanism. 2.6 Theft protection system (optional) The power tool may be equipped with the TPS Theft Protection System as an option. If the power tool is equipped with this feature, it can be unlocked and made ready for operation only through use of the corresponding TPS key. 2.
2.12 Using extension cords outdoors When working outdoors, use only extension cords that are approved and correspondingly marked for this application. 2.13 Using a generator or transformer en This power tool may be powered by a generator or transformer when the following conditions are fulfilled: The unit must provide a power output in watts of at least twice the value printed on the type identification plate on the power tool.
4. Technical data Right of technical changes reserved. Rated voltage 120 V Rated current input 15 A Power tool TE 3000‑AVR Mains frequency Weight of power tool Dimensions (L x W x H) 60 Hz 29.9 kg (65.92 lb) 808 mm (31.81") x 610 mm (24.02") x 209 mm (8.23") 860/min 68 J 10.8 kg (23.81 lb) Hammering frequency under load Single impact energy Weight of transport trolley en 5. Safety instructions NOTE The safety rules in section 5.
en Power tool TE 3000‑AVR Weight of transport trolley 10.8 kg NOTE The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool.
en 5.1.3 Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
d) Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers during breaks between working. e) Always lead the supply cord and extension cord away from the power tool to the rear while working. This helps to avoid tripping over the cord while working. f) Children must be instructed not to play with the appliance. g) The appliance is not intended for use by children, by debilitated persons or those who have received no instruction or training.
en b) Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace may result in damage to the health. c) If the work involves breaking right through, take the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. d) Be sure to keep an adequate distance from other persons and adjacent objects. If necessary, cordon off the area in which you are working. 5.2.
7. Operation DANGER Always hold the power tool securely with both hands on the grips provided. Keep the grips dry, clean and free from oil and grease. 7.1 Preparing for use CAUTION Wear protective gloves when changing insert tools as the insert tools get hot through use and they may have sharp edges. CAUTION When changing insert tools, take care to handle the locking mechanism correctly. You may otherwise risk pinching your fingers.
en CAUTION Remove the insert tool before laying the power tool down or placing it on the transport trolley. Disconnect the mains plug from the power outlet. Unintentional starting (accidental contact with the on / off switch) may cause the power tool to kick. 7.2.1.2 Activation of the theft protection system for the power tool NOTE Further detailed information on activation and use of the theft protection system can be found in the operating instructions for the theft protection system. 7.2.
8.3 Service indicator NOTE The power tool is equipped with a service indicator. Indicator Constant red light 8.4 Maintenance WARNING Repairs to the electrical section of the power tool may be carried out only by trained electrical specialists. Check all external parts of the power tool for damage at regular intervals and check that all controls operate faultlessly. Do not operate the power tool if parts End of service interval - servicing is due.
en Fault Possible cause Remedy The power tool doesn’t start and the indicator lamp blinks yellow. The power tool doesn’t start or cuts out during operation. The power tool has not been unlocked (power tools with optional theft protection system). The extension cord is too long or its gauge is inadequate. Use the TPS key to unlock the power tool. Use an extension cord of an approved length and / or of adequate gauge.
Hilti Corporation 426347 / A 426347 Hilti = registered trademark of Hilti Corp., Schaan W 3750 1209 00-Pos. 3 1 Printed in Liechtenstein © 2009 Right of technical and programme changes reserved S. E. & O. *426347* LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.