SJD 6-A22 English Printed: 11.10.
Printed: 11.10.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of signs used 1.2.
▶ Write down the serial number in the table below. Always quote this information when you contact a Hilti representative or Hilti Service to enquire about the product. Product information Orbital-action jig saw Generation Serial no. SJD 6-A22 01 1.5 Declaration of conformity We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards. A copy of the document issued by the certification body can be found at the end of this documentation.
▶ ▶ ▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
2.3 Additional safety instructions Personal safety ▶ Use the power tool only when it is in technically faultless condition. ▶ Never tamper with or modify the power tool in any way. ▶ Always hold the power tool with both hands on the grips provided. Keep the grips clean and dry. ▶ Suitable protective glasses, ear protection and protective gloves must be worn while the power tool is in use. ▶ Wear protective gloves when changing the accessory tool.
3 Description 3.1 Product overview English Printed: 11.10.
@ ; = % & ( ) + § / : Lockbutton On/off switch Grip Stroke rate regulator thumbwheel Battery state of charge indicator Battery release button Battery Air vents Suction adapter Catches Base plate ∙ $ £ | ¡ Q W E R T Cutting angle adjustment scale Orbital-action adjustment lever Saw blade Contact guard Guard Blade holder LED light Saw blade release lever Anti-splinter insert Electric supply for the SJD DRS-6A dust removal module (accessory) 3.
3.7 4 orbital-action settings The 4 orbital-action settings allow cutting performance and quality of cut to be adjusted to suit the material to be cut. The orbital-action adjustment lever is used to set the power tool to one of the 4 settings. The lower the orbital-action setting, the finer and cleaner the cut edges will be. The optimum setting can be determined by carrying out practical tests.
Stroke length Stroke rate under no load (n0) Maximum cutting performance in wood Maximum cutting performance in aluminium Maximum cutting performance in unalloyed steel Cutting angle (left/right) Suction adapter outside diameter SJD 6-A22 1.1 in (28 mm) 75 /min …3,000 /min 5.9 in (150 mm) 1.0 in (25 mm) 0.4 in (10 mm) 0° …45° 1.08 in (27.5 mm) 5 Before use 5.1 Preparations at the workplace CAUTION Risk of injury! Inadvertent starting of the product.
5.3 Removing the battery 1. Press the battery release buttons. 2. Remove the battery from the tool. 5.4 Fitting the saw blade 1. Remove the battery. → page 9 2. Push the saw blade (teeth facing the cutting direction) into the blade holder until it engages. 3. Grip and pull the saw blade to check that it is held securely. 5.5 Ejecting the saw blade WARNING Risk of injury. Uncontrolled ejection of the saw blade can lead to injury.
1. Remove the battery. → page 9 2. Push the saw blade release lever to the side, as far as it will go. ◁ The saw blade will be released and ejected. 5.6 Fitting the guard 1. Remove the battery. → page 9 2. Push the guard onto the power tool from the front until it clicks into place. Note The guard can be fitted only when the base plate is in the normal position (zero degrees position). 5.7 Removing the guard 1. Remove the battery. → page 9 10 English Printed: 11.10.
2. Tilt the guard slightly and pull it off toward the front. 5.8 Dust removal system Note The dust removal system reduces dust emissions, increases working safety by providing better visibility of the cutting line and reduces exposure to dust and wood chips at the workplace. 1. Fit the guard. → page 10 2. Connect the dust removal system to the suction adapter when you intend to work for long periods on wood or other materials that can generate high levels of dust. 5.8.1 Fitting the suction adapter 1.
5.8.2 Removing the suction adapter 1. Press the two retaining catches inwards. 2. Pull the suction adapter away from the base plate toward the rear. 3. Pull the vacuum cleaner hose off the suction adapter. 5.8.3 Cleaning the suction adapter 1. 2. 3. 4. 5. Remove the battery. → page 9 Remove the suction adapter. → page 12 Clean the suction adapter. Check that the catches are undamaged. Fit the suction adapter. → page 11 5.9 Setting the orbital action 1.
▶ Set the stroke rate regulator thumbwheel to a setting between 1 (low) and 6 (high). 5.11 Setting the cutting angle 1. Remove the battery. → page 9 2. Remove the suction adapter. → page 12 3. Slacken the screw on the base plate. 4. Adjust the base plate to the desired cutting angle (from 0° to 45° in both directions). Note When set to a cutting angle of 0°, the base plate is engaged in position to prevent rotation. To set a different cutting angle, the base plate must first be pulled back.
1. Remove the battery. → page 9 2. Press the anti-splinter insert into the base plate from below. 6 Operation 6.1 Switching on 1. Insert the battery. → page 8 Note A safety interlock ensures that the tool doesn’t start when the tool is first switched on and the battery then fitted, i.e. slid into place on the tool. 2. 3. 4. 5. Check that the lockbutton is in the middle position. Press the on/off switch. To lock the switch in the “on” position, then push the lockbutton to the right.
4. Press the product firmly against the workpiece and begin the plunge cut by slowly reducing the angle of attack. 5. Once the blade has penetrated right through the workpiece, bring the product into its normal working position. ◁ The base plate then lies flat on the working surface. 6. Continue to saw along the cutting line. 7 Care 7.
Storage CAUTION Inadvertent damage caused by defective battery. A leaking battery may damage the tool. ▶ Always remove the battery before storing the tool. Store the tool and batteries in a place that is as cool and dry as possible. Never store batteries in direct sunlight, on heating units or behind a window pane. Store the tool and batteries in a place where they cannot be accessed by children or unauthorized persons. Check the tool and batteries for damage before use after long periods of storage.
It collects a high percentage of the dust generated and can be quickly and easily attached to the orbitalaction jig saw. The dust removal module is equipped with a suction fan. This fan is driven by its own motor. When the orbital-action jig saw is switched on the dust removal module draws its electric power from the power tool’s battery. The dust removal module is not suitable for working on materials containing asbestos, metal dust and glass- or carbon-fiber dust.
18 English Printed: 11.10.
Printed: 11.10.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 11.10.
