PM 30-MG Printed: 08.05.
Printed: 08.05.
PM 30-MG Original operating instructions Printed: 08.05.
Printed: 08.05.
1 Information about the documentation 1.1 • • • About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
Wireless data transfer Hilti Li-ion battery type series used. Observe the information given in the section headed Intended use Pendulum locked (laser beam inclined) Pendulum unlocked (self-leveling system active) 1.4 Product information products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards.
2.2 ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ 2.3 Proper preparation of the working area Avoid awkward body positions when working from ladders. Make sure you work from a safe stance and stay in balance at all times. Secure the site in which you are taking measurements and take care to avoid directing the beam towards other persons or towards yourself when setting up the tool. Measurements taken through panes of glass or other objects may be inaccurate.
3 Description 3.1 Product overview @ ; = % 4 Line mode button Liion battery Warning sticker Receiver mode button English Printed: 08.05.
3.2 Intended use This tool is a self-leveling multi-line laser level that allows a single person to transfer right angles, level horizontally, carry out alignment work and plumb accurately. The product has three green 360° laser lines, a reference point directed downward on the right-hand front of the measuring device, as well as four beam intersection points (front, back, left, right and above) with a range of approx. 20 m. Range depends on the brightness of ambient light.
Line thickness Laser class Operating status indicator Power source Battery life (all lines on) Battery life (horizontal or vertical lines on) Operating temperature Storage temperature Dust and water spray protection (except battery compartment) < 2.2 mm at 5 m (typical) (< 0.
5.5 Switching the laser beams on 1. Set the selector switch to the position (ON / unlocked). ➥ The vertical laser lines are switched on. 2. Press the line mode button repeatedly until the desired line mode is set. ➥ The operating modes change in the following sequence and the sequence repeats itself: vertical lines, vertical side line, horizontal line, vertical and horizontal lines. 5.6 Switching the laser beams off 1. Set the selector switch to the OFF position.
5.8.2 Setting up drywall track for a partition wall 5.8.3 Vertical alignment of pipes 8 English Printed: 08.05.
5.8.4 Aligning heating units 5.8.5 Aligning door and window frames English Printed: 08.05.
5.9 Checking 5.9.1 Checking the plumb point 1. 2. 3. 4. In a high room (for example in a stairwell with a height of 10 m), make a mark (a cross) on the floor. Place the tool on an even, level surface. Switch the tool on and unlock the pendulum. Position the tool so that the lower plumb beam coincides with the center of the cross marked on the floor. 5. Mark the top point of intersection of the laser lines on the ceiling. 6. Pivot the tool through 90°.
9. Calculate the value R. ➥ The value R should be less than 3 mm (corresponds to 3 mm at 10 m). ➥ The value R should be less than 1/8". 5.9.2 Checking the leveling of the laser beam 1. The distance between the walls must be at least 10 m. 2. Place the tool on an even, level surface approx. 20 cm from the wall (A) with the point of intersection of the laser lines directed toward the wall (A). 3. Mark the point of intersection of the laser lines with a cross (1) on wall (A) and with a cross (2) on wall (B).
8. Calculate the value R. ➥ The value R should be less than 3 mm. ➥ The value R should be less than 1/8". 5.9.3 Checking perpendicularity (horizontal) 1. Position the tool so that the lower plumb beam coincides with the center of a reference cross marked in the middle of a room at a distance of about 5 m from the walls. 2. Mark all 4 points of intersection on the four walls. 3.
7. Align the laser beam so that it strikes the target plate T1 and the position marked on it. 8. Mark the new position on target plate T2. 9. Read the distance D between the two marks on target plate T2. If the difference D is greater than 3 mm, the tool must be returned to a Hilti repair center for adjustment. 6 6.1 ▶ ▶ ▶ ▶ 6.2 Care and maintenance Cleaning and drying Blow any dust off the glass. Do not touch the glass surfaces with your fingers. Use only a soft, clean cloth to clean the tool.
Trouble or fault The tool can’t be switched on. Individual laser beams don’t function. The tool can be switched on but no laser beam is visible. Automatic leveling doesn’t work. Possible cause Device or selector switch faulty. The laser source or laser control unit is faulty. The laser source or laser control unit is faulty. The temperature is too high or too low. The tool is standing on an excessively inclined surface. Selector switch in the position. The inclination sensor is faulty.
Printed: 08.05.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 08.05.
