SCM 22-A English Printed: 01.09.
Printed: 01.09.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed. The type designation and serial number are printed on the type identification plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Type: Generation: Serial no.
▶ ▶ Maintain power tools properly. Check that moving parts are in correct working order and do not jam, and check whether any parts are broken or so damaged that correct operation of the power tool cannot be guaranteed. If any parts are damaged, have these parts repaired before using the tool. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control. 2.
▶ ▶ ▶ ***** For internal use only ***** 26.07.2016 / 17:07:30 - H2\DOK-Projekt\System\SCM_22-A-G1\ENU\SCM18-A_P3 ▶ Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
for the type of dust generated. Ensure that the workplace is well ventilated. Follow national requirements for the materials you want to work with. Careful handling and use of batteries ▶ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. ▶ Do not expose batteries to high temperatures and keep them away from fire. There is a risk of explosion. ▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80°C (176°F).
6 Printed: 01.09.2017 | Doc-Nr: PUB / 5292934 / 000 / 01 00 ***** For internal use only ***** 26.07.
7 Printed: 01.09.2017 | Doc-Nr: PUB / 5292934 / 000 / 01 00 ***** For internal use only ***** 26.07.
***** For internal use only ***** 26.07.2016 / 17:07:30 - H2\DOK-Projekt\System\SCM_22-A-G1\ENU\SCM18-A_P3 3 Description 3.1 Overview of the product 8 Printed: 01.09.
@ ; = % & ( ) + § / : ∙ Auxiliary grip Switch-on interlock release button On/off switch Grip Charge state and fault display Battery release button Chip collector Pivoting guard operating lever Drive spindle Base plate Pivoting guard Rip fence (parallel guide) $ £ | ¡ Q W E R T Z U I Saw blade position indicator LED / viewing window Hood Drive spindle lockbutton Cutting line indicator Parallel guide (rip fence) clamp Battery Clamping lever for cutting depth adjustment Hex.
3.6 Accessories Clamping flange, mounting flange, clamping screw. 4 Technical data 4.1 Circular saw SCM 22A Weight Saw blade diameter Blade disc thickness ***** For internal use only ***** 26.07.2016 / 17:07:30 - H2\DOK-Projekt\System\SCM_22-A-G1\ENU\SCM18-A_P3 Kerf width Saw blade arbor size Rated speed under no load Maximum cutting depth 8.8 lb (4.0 kg) 6.3 in …6.5 in (160 mm …165 mm) 0.05 in (1.2 mm) 0.06 in (1.6 mm) 0.8 in (20 mm) 3,500 /min 2.2 in (57 mm) 5 Operation 5.
5.3 Removing the saw blade WARNING Risk of burning injury. A hot accessory tool, clamping flange or clamping screw and the sharp edges of the saw blade present hazards. Wear protective gloves when changing saw blades. 1. Insert the hex. socket wrench in the saw blade clamping screw. 2. Press the spindle lockbutton and hold it in this position. 3. Turn the saw blade clamping screw with the hex. socket wrench until the spindle lockbutton engages fully. 4. Release the clamping screw by turning the hex.
4. Fit the new saw blade. Note Observe the direction-of-rotation arrow on the saw blade and on the power tool. They must correspond. 5. 6. 7. 8. 9. Fit the outer clamping flange the right way round. Insert the clamping screw. Insert the hex. socket wrench in the saw blade clamping screw. Press the drive spindle lockbutton. Secure the clamping flange with the clamping screw by turning the hex. socket wrench in the opposite direction to the direction-of-rotation arrow. ◁ The spindle lockbutton engages. 10.
Push the battery into the product from the rear as far as it will go and until it is heard to engage with a double click. 5.7 Sawing along a line Note Secure the workpiece to prevent movement. Position the workpiece so that the saw blade is free to rotate beneath it. Check to ensure that the on/off switch on the product is in the “off” position. Position the forward section of the saw’s base plate on the workpiece but do not bring the blade into contact with the workpiece. 1.
***** For internal use only ***** 26.07.2016 / 17:07:30 - H2\DOK-Projekt\System\SCM_22-A-G1\ENU\SCM18-A_P3 5.8 Fitting / adjusting the rip fence (parallel guide) 1. Press the clamp together. 2. Push the parallel guide into the base plate as far as desired. 3. Release the clamp when the parallel guide is in the desired position. 5.9 Emptying the chip collector WARNING Risk of injury! Hot or sharp metal cuttings / chips present a hazard. ▶ 1. 2. 3. 4.
6 Care, maintenance, transport and storage 6.1 Care and maintenance of cordless tools WARNING Danger of electric shock! Carrying out care and maintenance while the battery is fitted presents a risk of serious physical injury and burning injury. ▶ Always remove the battery before carrying out all care and maintenance tasks. Care of the lithiumion batteries • Keep the battery free from oil and grease. • Use only a slightly damp cloth to clean the casing.
Malfunction 1 LED blinks. 4 LEDs blink. Possible cause The battery is discharged. Action to be taken ▶ The battery is too hot or too cold. ▶ The circular saw was overloaded briefly. ▶ The overheating prevention cut-out has been activated. ▶ Change the battery and charge the empty battery. Bring the battery to the recommended working temperature. Release the control switch and then press it again. Allow the circular saw to cool down to cool down and clean the air vents. 7.
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. 9 Manufacturer’s warranty Please contact your local Hilti representative if you have questions about the warranty conditions. ***** For internal use only ***** 26.07.
Printed: 01.09.2017 | Doc-Nr: PUB / 5292934 / 000 / 01 00 ***** For internal use only ***** 26.07.
Printed: 01.09.
Printed: 01.09.2017 | Doc-Nr: PUB / 5292934 / 000 / 01 00 ** Hilti = registered trademark of Hilti Corp.
