Use and Care Manual
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Using extension cords
- 6 Preparations at the workplace
- 6.1 Securing the drill stand with an anchor
- 6.2 Securing the drill stand by vacuum
- 6.3 Fastening the drill stand with the threaded spindle
- 6.4 Fitting the hand wheel on the drill stand
- 6.5 Adjusting the side handle
- 6.6 Setting the depth gage (accessory)
- 6.7 Securing the diamond core drilling machine in the drill stand
- 6.8 Detaching the diamond core drilling machine from the drill stand
- 6.9 Adjusting the play between the rail and carriage
- 6.10 Adjusting the drilling angle when using the drill stand with combination base plate
- 6.11 Connecting the vacuum removal system
- 6.12 Fitting the water supply connection
- 6.13 Install water collection system for drill stand (accessory)
- 6.14 Installing water collection system (accessory) for hand-guided mode
- 7 Operation
- 7.1 Fitting a diamond core bit in a BI+ chuck
- 7.2 Fitting the diamond core bit with an alternative type of chuck
- 7.3 Removing a diamond core bit from a BI+ chuck
- 7.4 Removing the diamond core bit with an alternative type of chuck
- 7.5 Selecting the speed
- 7.6 Activate/deactivate continuous running lock
- 7.7 Operating portable residual current device (PRCD)
- 7.8 Use of the two-part hole-starting aid
- 7.9 Dry drilling with vacuum cleaner via built-in power outlet for electric devices
- 7.10 Dry-drilling with using a vacuum extractor without power outlet for power tools
- 7.11 Dry drilling without dust removal
- 7.12 Hand-guided wet drilling without water collection system
- 7.13 Hand-guided wet-drilling with the water collection system
- 7.14 Wet-drilling with the drill stand
- 7.15 Using the Rota-Rail (column swivel)
- 8 Care and maintenance
- 9 Transport and storage
- 10 Troubleshooting
- 11 Disposal
- 12 FCC statement / ISED statement
- 13 Manufacturer’s warranty
- 14 Further information
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation de câbles de rallonge
- 6 Préparatifs
- 6.1 Fixation de la colonne de forage avec bride d'ancrage
- 6.2 Fixation de la colonne de forage avec une semelle-ventouse
- 6.3 Fixation de la colonne de forage avec une broche filetée
- 6.4 Montage du volant à main sur la colonne de forage
- 6.5 Réglage de la poignée latérale
- 6.6 Réglage de la butée de profondeur (accessoire)
- 6.7 Fixation de la carotteuse diamant sur la colonne de forage
- 6.8 Démontage de la carotteuse diamant de la colonne de forage
- 6.9 Réglage du jeu entre la crémaillère et le boîtier de guidage
- 6.10 Réglage de l'angle de forage sur la colonne à l'aide de la semelle combinée
- 6.11 Raccordement du dispositif d'aspiration
- 6.12 Installation du raccordement d'eau
- 6.13 Montage du système de récupération d'eau pour le forage manuel (accessoire)
- 6.14 Montage du système de récupération d'eau pour le forage manuel (accessoire)
- 7 Utilisation
- 7.1 Montage de la couronne diamantée avec le porte-outil BI+
- 7.2 Montage de la couronne diamantée avec un porte-outil alternatif
- 7.3 Démontage de la couronne diamantée avec le porte-outil BI+
- 7.4 Démontage de la couronne diamantée avec un porte-outil alternatif
- 7.5 Sélection de la vitesse de rotation
- 7.6 Activation/Désactivation du dispositif de blocage en continu
- 7.7 Activation du disjoncteur à tension nulle PRCD
- 7.8 Utilisation d'une amorce de forage constituée de deux éléments
- 7.9 Forage à sec avec aspirateur via la prise secteur intégrée pour appareils électriques
- 7.10 Forage à sec avec aspirateur sans prise secteur pour outils électroportatifs
- 7.11 Forage à sec sans dispositif d'aspiration de poussières
- 7.12 Forage à l'eau en mode manuel sans système de récupération d'eau
- 7.13 Forage à l'eau en mode manuel avec système de récupération d'eau
- 7.14 Forage à l'eau avec colonne
- 7.15 Utilisation du rail Rota (élément rotatif de la colonne)
- 8 Nettoyage et entretien
- 9 Transport et entreposage
- 10 Aide au dépannage
- 11 Recyclage
- 12 Déclaration FCC/Déclaration ISED
- 13 Garantie constructeur
- 14 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Uso de alargadores
- 6 Preparación del trabajo
- 6.1 Fijación del soporte con taco
- 6.2 Fije el soporte mediante vacío
- 6.3 Fijación del soporte con un husillo roscado
- 6.4 Montaje de la rueda de mano en el soporte
- 6.5 Ajuste de la empuñadura lateral
- 6.6 Ajuste del tope de profundidad (accesorio)
- 6.7 Fijación de la perforadora de diamante en el soporte
- 6.8 retirada de la perforadora de diamante del soporte
- 6.9 Ajuste del juego entre el raíl y el carro
- 6.10 Ajuste el ángulo de perforación en el soporte con placa base combinada
- 6.11 Conexión de un dispositivo de aspiración
- 6.12 Instalación de la toma de agua
- 6.13 Montaje del sistema colector de agua para soporte (accesorio)
- 6.14 Montaje del sistema colector de agua para el modo manual (accesorio)
- 7 Manejo
- 7.1 Montaje de la corona perforadora de diamante con portaútiles BI+
- 7.2 Montaje de la corona perforadora de diamante con portaútiles alternativo
- 7.3 Desmontaje de la corona perforadora de diamante con portaútiles BI+
- 7.4 Desmontaje de la corona perforadora de diamante con portaútiles alternativo
- 7.5 Selección de la velocidad
- 7.6 Activación/desactivación del bloqueo de larga duración
- 7.7 Manejo del interruptor de corriente de defecto PRCD
- 7.8 Uso de la guía de centrado de dos piezas
- 7.9 Taladrado en seco con aspirador de polvo mediante toma de corriente integrada para herramientas eléctricas
- 7.10 Taladrado en seco con aspirador de polvo sin toma de corriente para herramientas eléctricas
- 7.11 Taladrado en seco sin aspiración
- 7.12 Taladrado manual en húmedo sin sistema colector de agua
- 7.13 Taladrado manual en húmedo con sistema colector de agua
- 7.14 Taladrado en húmedo con soporte
- 7.15 Uso del raíl rotatorio (pieza giratoria para columnas)
- 8 Cuidado y mantenimiento
- 9 Transporte y almacenamiento
- 10 Ayuda en caso de averías
- 11 Reciclaje
- 12 Indicación FCC / Indicación ISED
- 13 Garantía del fabricante
- 14 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização de extensões de cabo
- 6 Preparação do local de trabalho
- 6.1 Fixar a coluna com bucha
- 6.2 Fixar a coluna com vácuo
- 6.3 Fixar coluna com varão de enroscar
- 6.4 Montar o volante à coluna
- 6.5 Ajustar o punho auxiliar
- 6.6 Ajustar o limitador de profundidade (acessório)
- 6.7 Fixar o perfurador diamantado na coluna de perfuração
- 6.8 Separar o perfurador diamantado da coluna
- 6.9 Ajustar a folga entre a guia e o patim
- 6.10 Ajustar o ângulo na coluna de perfuração com base combinada
- 6.11 Ligar o sistema de extracção
- 6.12 Ligar o fornecimento de água
- 6.13 Montar o sistema colector de água para coluna de perfuração (acessório)
- 6.14 Montar o sistema colector de água para modo manual (acessório)
- 7 Utilização
- 7.1 Montagem da coroa diamantada de perfuração com porta-ferramentas BI+
- 7.2 Montar a coroa diamantada com porta-ferramentas alternativo
- 7.3 Desmontagem da coroa diamantada de perfuração com porta-ferramentas BI+
- 7.4 Desmontagem da coroa diamantada com porta-ferramentas alternativo
- 7.5 Seleccionar a rotação
- 7.6 Activar/desactivar o bloqueio do funcionamento contínuo
- 7.7 Operar o disjuntor de segurança PRCD
- 7.8 Utilização da broca de centragem de duas peças
- 7.9 Perfuração a seco com aspirador através de tomada de rede integrada para aparelhos eléctricos
- 7.10 Perfuração a seco com aspirador sem tomada de rede para ferramentas eléctricas
- 7.11 Perfuração a seco sem sistema de remoção de pó
- 7.12 Perfuração manual a água sem sistema colector de água
- 7.13 Perfuração manual a água com sistema colector de água
- 7.14 Perfuração a húmido com coluna de perfuração
- 7.15 Utilização do Rota-Rail (peça de rotação da coluna)
- 8 Conservação e manutenção
- 9 Transporte e armazenamento
- 10 Ajuda em caso de avarias
- 11 Reciclagem
- 12 Declaração FCC / Declaração ISED
- 13 Garantia do fabricante
- 14 Mais informações
*2204401*
2204401 English 21
4. Plug the vacuum extractor’s supply cord into the power outlet.
5.
When connected: Press the Reset switch or I button of the PRCD.
6. Center the diamond core drilling machine where the hole is to be drilled.
7. Press the on/off switch on the diamond core drilling machine.
The vacuum extractor will start after the power tool has started. When you switch off the power
tool the vacuum extractor will run on for a short time before switching itself off.
7.10 Dry-drilling with using a vacuum extractor without power outlet for power tools
Use slotted core bits only when working without a dust removal system.
1. Secure the side handle in the desired position.
2. Optional: Fit and use the two-part hole-starting aid. → page 20
3. Plug the vacuum cleaner’s supply cord into the power outlet and switch the vacuum cleaner on.
4. Plug the supply cord of the diamond core drilling machine into the power outlet and then press the
"Reset button or I button of the PRCD.
5. Center the diamond core drilling machine where the hole is to be drilled.
6. Press the on/off switch on the diamond core drilling machine.
7. To ensure removal of residual dust, let the vacuum extractor run on for a few seconds after you switch
off the machine.
7.11 Dry drilling without dust removal
If dry drilling without a dust removal system is carried out, use slotted core bits. Wear suitable
breathing protection!
Do not drill upward when working without a dust removal system.
1. Secure the side handle in the desired position.
2. Optional: Fit and use the two-part hole-starting aid. → page 20
3.
Plug the supply cord into the power outlet and press the Reset button or I button of the PRCD.
4. Center the diamond core drilling machine where the hole is to be drilled.
5. Press the on/off switch on the diamond core drilling machine.
7.12 Hand-guided wet drilling without water collection system
WARNING
Risk of personal injury and material damage The diamond core drilling machine may become damaged
and the risk of electric shock is increased.
▶ Use of the water collection system in conjunction with a wet-type industrial vacuum cleaner is a mandatory
requirement for wet drilling overhead.
1. Secure the side handle in the desired position.
2. Optional: Fit and use the two-part hole-starting aid. → page 20
3.
Plug the supply cord into the power outlet and press the Reset button or I button of the PRCD.
4. Center the diamond core drilling machine where the hole is to be drilled.
5. Slowly open the water flow regulator until the water flows at the desired rate. The indicator on the side
handle enables you to check the water flow.
6. Press the on/off switch on the diamond core drilling machine.
7.13 Hand-guided wet-drilling with the water collection system
WARNING
Danger of electric shock! There is a possibility of water flowing over the motor and cover if the vacuum
removal system is faulty.
▶ Cease operations immediately if the vacuum removal system is not working.