DST WRC-CA Printed: 09.03.
Printed: 09.03.
Contents 1 1.1 1.2 Information about the documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2.3 Symbols in the illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Explanation of symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 1.3 1.4 1.5 1.
5.9 Activating cooling water control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.10 Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11 Setting screen brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.12 Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.13 Reading messages . . . . . . .
CAUTION CAUTION ! ▶ Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property. 1.2.2 Symbols in the documentation The following symbols are used in this document: Read the operating instructions before use. Instructions for use and other useful information Dealing with recyclable materials Do not dispose of electric equipment and batteries as household waste 1.2.
The type designation and serial number are stated on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Remote control unit Generation Serial no. 1.6 DST WRC-CA 01 Declaration of conformity We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards.
▶ ▶ ▶ ▶ ▶ Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools.
2.3 Battery use and care Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion batteries. Do not expose batteries to high temperatures, direct sunlight or fire. Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C. Do not attempt to charge or continue to use damaged batteries. If the battery is too hot to touch it may be defective.
3.2 @ ; = % & ( 3.
After you switch on the remote control unit, in order to start the first advance you have to turn the control knob clockwise at the same time as you operate the joystick. 3.6 Control knob The control knob enables you to select the following functions: • • Set drive parameters. Select a preset or set a value in the "Settings"". If a value can be selected or set by turning the control knob, the control knob symbol the value or the selectable settings. 3.
Up Down Next OK Add data record Delete data record Continue Back Cut Assist Manual mode Set operating hours to zero List of blade diameters Turn cooling water ON Turn cooling water OFF Define obstacle Overcut Stop/hold Stop/pause Cancel without saving 3.
4.2 Wireless communication (between the DST WRC-CA remote control unit and wall/diamond saw) Frequency band 2,400 MHz …2,483.5 MHz Range 65 ft - 10 in (20 m) Maximum emitted transmission power 4.3 10,9 dBm PUA 81 charger Rated supply current 115 V …230 V Rated power 36 VA AC frequency Rated voltage Operating temperature Storage temperature (dry) Charging temperature 4.
5 Preparations at the workplace CAUTION Risk of damage due to severe heat ! ▶ Always remove the battery from the remote control unit for charging. ▶ 5.1 Charge the battery fully before using it for the first time. Removing the battery 1. Turn the catch in a counter-clockwise direction until the “unlocked” symbol appears. 2. Remove the battery from the slot in the remote control unit. 5.2 Charging the battery 1. Connect the plug of the charger to the battery. 2.
3. 4. 5. 6. Use the control knob to select the fuse rating for the electricity supply (A). Use the <> button to proceed to the next setting. Use the control knob to set the line attenuation. Use <> to confirm your settings. ◁ The settings will be saved and the fuse rating then displayed in the status bar in the display. Certain line configurations (e.g. extension cables) can cause recurrent appearances of the "Overload shutdown" message. If this happens, change the line attenuation setting. 5.
4. Use <> to confirm your settings. 5.10 Changing the password 1. On the HOME screen, select <>. 2. Select and confirm your choice with <>. 3. Use the control knob to enter the old password digit by digit. ◁ If you have forgotten the password, you have to reset to the default settings. 4. Confirm the old password with <>. ◁ The Change password screen appears on the display. 5. Use the <> button to proceed to the next setting. 6.
5.15 Technical information and next service This screen tells you about operating hours logged, the operating-hours countdown until the next service is due, serial numbers and version numbers of the hardware and the software. 1. 2. 3. 4. On the HOME screen, select <>. Select and confirm your choice with <>. Use <> or <> as appropriate to proceed to the next screen. Use <> to exit the screen. 5.16 Resetting the settings 1. Press the HOME button. 2.
12. Press the DRIVE ON/OFF button. ◁ The drive of the saw blade stops. 13. If automatic cooling water control is not activated, turn off the cooling water with <>. 14. Move the saw head to a position in which it can easily be removed. 15. Press the EMERGENCY STOP button. 7 Assisted operation with Cut Assist 7.1 Overview This remote control unit features the Cut Assist function. It automates various work steps.
14. Use <> to confirm your settings. ◁ The Length of cut screen appears on the display. On this screen the length of cut can be defined, an obstacle indicated and overcutting at the end of the cut allowed. 15. Define whether an overcut is allowed at the end of the cut. ◁ When overcutting, the cut is extended so that the set length of cut is also reached, as far as possible, at the reverse side of the wall being cut through. 16. Press the <> button if, within approx.
3. Use the control knob to set the outside diameter of the saw blade and the blade guard. ◁ The outside diameter you enter influences blade speed of rotation and the depth and length of the cut. 4. Disengage the EMERGENCY STOP button. 5. Use <> to confirm your entries. ◁ The Cut Assist in progress screen is grayed. 6. Press the DRIVE ON/OFF button to resume cutting. ◁ The Cut Assist in progress screen appears on the display. 7.
9 Transport and storage of cordless tools Transport CAUTION Accidental starting during transport ! ▶ Always transport your products with the batteries removed! Remove the battery. Transport the tool and batteries individually packaged. Never transport batteries in bulk form (loose, unprotected). Check the tool and batteries for damage before use after long periods of transport.
12 ▶ 13 Manufacturer’s warranty Please contact your local Hilti representative if you have questions about the warranty conditions. FCC statement (applicable in US) / IC statement (applicable in Canada) This device complies with Part 15 of the FCC Rules and RSS-210 of lC. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
20 English Printed: 09.03.
Printed: 09.03.
Printed: 09.03.
Printed: 09.03.
*2053458* 2053458 Hilti = registered trademark of Hilti Corp., Schaan Printed: 09.03.