Operating Instruction HDE 500-22 (02)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 6 Operation
- 7 Care and maintenance
- 8 Transport and storage of cordless tools and batteries
- 9 Troubleshooting
- 10 Disposal
- 11 Manufacturer’s warranty
- 12 Further information
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des outils sur accu et des accus
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- 12 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las baterías y sus herramientas
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Garantía del fabricante
- 12 Más información
- Manual de instruções original
8 English 2293683
*2293683*
Status Dispensing-wheel
setting/symbol
Meaning
LED shows red
Discard function
Repeat function
Measured dispensing
Discarding/dispensing aborted.
Discarding/dispensing volume not fully ejected.
LED flashes red
Discard function
Repeat function
Measured dispensing
The volume left in the pack is not sufficient for the
next dispensing operation or repeat of the previous
dispensing operation as set by means of the dispensing
wheel, or for the discharge function.
4 Technical data
HDE 50022
Weight without battery
1.9 kg
(4.2 lb)
Rated voltage
21.6 V
Storage temperature
−40 ℃ … 85 ℃
(−40 ℉ … 185 ℉)
Ambient temperature for operation
−17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
4.1 Battery
Battery operating voltage
21.6 V
Weight, battery
See the end of these
operating instructions
Ambient temperature for operation
−17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
Storage temperature
−20 ℃ … 40 ℃
(−4 ℉ … 104 ℉)
Battery charging starting temperature
−10 ℃ … 45 ℃
(14 ℉ … 113 ℉)
5 Preparations at the workplace
WARNING
Risk of injury by inadvertent starting!
▶ Before inserting the battery, make sure that the product is switched off.
▶ Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 6
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.